Casio Projector XJ-V1 User Manual

11
To use manual keystone correction (KEYSTONE)
The projector has a keystone correction feature that prevents 
distortion of the projected image when projecting from an 
angle. 
You can use the [KEYSTONE +] and [KEYSTONE –] keys to 
adjust keystone correction manually.
To zoom an image (D-ZOOM)
1.Press the [D-ZOOM +] key.
zThis will enlarge the center of the projected image one step.
2.To zoom in on the center of the projected image more, press the [D-ZOOM +] 
key again. To zoom out, press the [D-ZOOM –]...

12
To auto adjust an image (AUTO)
Press the [AUTO] key.
zPressing the [AUTO] key automatically adjusts the frequency and phase in accordance with the 
input signal, which can reduce flickering and other projected image problems.
zThis operation is supported while the input source is Computer (RGB).
To change the aspect ratio of the projected image (ASPECT)
Press the [ASPECT] key to cycle through the aspect ratio settings for the projected image.
The table below shows the settings available for each type...

13
To adjust image brightness (FUNC)
1.Press the [FUNC] key. On the menu that appears, select “Brightness” and then 
press the [ENTER] key.
2.On the brightness adjustment screen that appears, use the [W] and [X] keys to 
adjust brightness.
3.To hide the window, press the [ESC] key.
To change the color mode (FUNC)
1.Press the [FUNC] key. On the menu that appears, select “Color Mode” and then 
press the [ENTER] key.
zThis displays the color mode selection window. The currently selected color mode is the...

14
You can use the remote controller [VOLUME +] and [VOLUME –] keys to adjust the volume level of the 
audio that is output from the AUDIO OUT terminal.
To adjust the volume level
1.Press the [VOLUME +] or [VOLUME –] key.
zThis causes the “Volume” screen to appear on the projected image.
2.Press the [VOLUME +] key to increase the volume, or the [VOLUME –] key to 
lower the volume.
3.After the setting is the way you want, press the [ESC] key.
To mute the audio
1.Press the [VOLUME +] or [VOLUME –] key to...

15
The following Eco Mode settings are available to specify whether priority should be given to 
low-power, low-noise operation or to projection brightness.
To select the Eco Mode
1.Press the [ECO] key.
zThis causes “Eco Mode” window to appear on the projection screen.
2.Use the [W] and [X] keys to select the setting you want.
zIf you select “On” here, go to step 3. If you select “Off”, jump to step 4.
3.Perform the following steps to adjust the “Eco Level” (the balance between 
low-power, quiet...

16
The presentation timer shows a countdown from a preset time value. You can use it to keep track of 
how much time has elapsed during your presentation, and to limit a presentation to a preset amount of 
time. You can configure the presentation timer so it is displayed in the projected image.
To display the timer
When the timer is not displayed on the projected image, press the [TIMER] key once.
The timer will appear for about five seconds and then disappear automatically if the “Off” is selected 
for...

17
To configure timer settings
1.Use the [TIMER] key to display the timer function menu.
2.Use the [T] and [S] keys to select the “Position”, “Continuous Display”, or “Start 
Time” setting and then change the settings as described in the table below.
3.To save your settings and close the timer function menu, press [ESC].
zTo start the timer immediately after changing its settings, use [T] and [S] to select “Start 
Timer” on the timer function menu and then press the [ENTER] key before pressing [ESC] in...

18
To pause the timer countdown
1.Use the [TIMER] key to display the timer function menu.
2.Select “Pause Timer” and then press the [ENTER] key.
To resume a paused timer countdown
1.Use the [TIMER] key to display the timer function menu.
2.Select “Restart Timer” and then press the [ENTER] key.
To reset the timer to its start time
1.Use the [TIMER] key to display the timer function menu.
2.Select “Reset Timer” and then press the [ENTER] key.
zThis will reset the time to the “Start Time” setting. 

19
Pressing the [MENU] key displays the Setup Menu shown below on the projection screen. You can 
use this menu to adjust projected image brightness, contrast, and other settings, and to change 
projector settings.
The guidance shows the key operations that can be performed for the currently selected (highlighted) 
menu item.
Basic Setup Menu Operations
Setup Menu Settings
zOne or more letters (such as RC) after the menu item name indicates an item that is available only 
when one or more particular...

20
Image Adjustment 13 
Eco Off ModeWhen “Off” is selected for the “Option Settings 1 3 Eco Mode” setting, specify 
either “Bright” (brightness priority) or “Normal*” (hue priority) as the image quality 
setting.
Image Adjustment 13 
Restore Menu DefaultsReturn all of the items in the “Image Adjustment 1” main menu to their initial defaults 
for the currently projecting image source.
Image Adjustment 23 
Vertical Position (RC)Adjust the vertical and horizontal positions of the input source image in...