Casio Exilim EX ZR100 User Manual

161Other Settings (Set Up)
Procedure
[MENU] * Set Up Tab * Language
.Specify the display language you want.
1Select the tab on the right.
2Select “Language”.
3Select the language you want.
• Camera models sold in certain geographic areas 
may not support display language selection.
Procedure
[MENU] * Set Up Tab * Sleep
This feature turns off the monitor screen whenever no camera operation is performed 
for a preset amount of time. Press any button to turn the monitor screen back on.
Trigger Time...

162Other Settings (Set Up)
Procedure
[MENU] * Set Up Tab * Auto Power Off
Auto Power Off turns off the camera whenever no camera operation is performed for 
a preset amount of time.
Trigger Time Settings: 2 min, 5 min, 10 min (The trigger time is always 5 minutes in 
the PLAY mode.)
• Auto Power Off is disabled under any of the following conditions.
– While the camera is connected to a computer or other device
– During a slideshow
– During CS group playback
– During movie recording and playback...

163Other Settings (Set Up)
Procedure
[MENU] * Set Up Tab * USB
You can use the procedure below to select the USB communication protocol, which is 
used when exchanging data with a computer, printer, or other external device.
Procedure
[MENU] * Set Up Tab * Video Out
You can use the procedure in this section to select either NTSC or PAL as the video 
output system. You can also specify an aspect ratio of 4:3 or 16:9.
• Select the aspect ratio (4:3 or 16:9) that matches the type of TV you plan to use....

164Other Settings (Set Up)
Procedure
[MENU] * Set Up Tab * HDMI Output
• See page 110 for details.
Procedure
[MENU] * Set Up Tab * Startup
Display the image you want to use as your startup image and then select “On”.
• The startup image does not appear when you turn on the camera by pressing [p] 
(PLAY).
• You can specify a snapshot you recorded as the startup image, or you can use the 
special startup image provided in the camera’s built-in memory.
• Formatting built-in memory (page 165) will delete the...

165Other Settings (Set Up)
Procedure
[MENU] * Set Up Tab * Format
If a memory card is loaded in the camera, this operation will format the memory card. 
It will format built-in memory if no memory card is loaded.
• The format operation will delete all contents on the memory card or in built-in 
memory. It cannot be undone. Make sure you do not need any data currently on 
the card or in built-in memory before you format it.
• Formatting built-in memory will delete the following data.
– Protected images
–...

166Configuring Monitor Screen Settings
Configuring Monitor Screen Settings
Each press of [8] (DISP) will cycle through display settings that display or hide on-
screen information and the control panel. You can configure separate settings for the 
REC mode and PLAY mode.
• The control panel is not displayed during movie recording.
Displays a histogram on the monitor screen which you can use to 
check the exposure of an image before you shoot it. You also can 
display the histogram in the PLAY mode for...

167Configuring Monitor Screen Settings
A histogram is a graph that represents the lightness of an image in terms of the 
number of pixels. The vertical axis indicates the number of pixels, while the horizontal 
axis indicates lightness. If the histogram appears too lopsided for some reason, you 
can use EV shift to move it left or right in order to achieve better balance. Optimum 
exposure can be achieved by EV shifting so the graph is as close to the center as 
possible. For snapshots, you can even...

168Appendix
Appendix
.Avoid Use While In Motion
• Never use the camera to record or play back images while operating an automobile 
or other vehicle, or while walking. Looking at the monitor while in motion creates 
the risk of serious accident.
.Flash
• Never use the flash unit in areas where flammable or explosive gas may be 
present. Such conditions create the risk of fire and explosion.
• Never fire the flash in the direction of a person operating a motor vehicle. Doing so 
can interfere with the...

169Appendix
.Smoke, abnormal odor, overheating, and other abnormalities
• Continued use of the camera while it is emitting smoke or strange odor, or while it 
is overheating creates the risk of fire and electric shock. Immediately perform the 
following steps whenever any of the above symptoms are present.
1. Turn off the camera.
2. Remove the battery from the camera, taking care to protect yourself against burn 
injury.
3. Contact your dealer or nearest CASIO authorized service center.
.Water and...

170Appendix
.Locations To Be Avoided
• Never leave the camera in any of the following types of locations. Doing so creates 
the risk of fire and electric shock.
– Areas subject to large amounts of humidity or dust
– Food preparation areas or other locations where oil smoke is present
– Near heaters, on a heated carpet, in areas exposed to direct sunlight, in a closed 
vehicle parked in the sun, or other areas subject to very high temperatures
• Never place the camera on an unstable surface, on a high...