Casio Exilim EX Z30 User Manual

							VIEWING IMAGES ON A COMPUTER
151
VIEWING IMAGES ON A COMPUTER
After using the USB cradle to establish a USB connection
between the camera and your computer, you can use your
computer to view images in file memory and copy images
to your computer’s hard disk or other storage media. In
order to do this, you first need to install the USB driver
located on the CD-ROM (CASIO Digital Camera Software)
that comes bundled with the camera onto your computer.
Note that the procedure you need to perform depends on
whether you are using computer running under Windows
(see below) or a Macintosh (see page 157).Using the Camera with a Windows
Computer
The following are the general steps for viewing and copying
files from a computer running under Windows. You can find
details about each operation in the procedures that follow
below. Note that you should also refer to the
documentation that comes with your computer for other
information about USB connections, etc.
1. If you are running Windows 98, Me, or 2000, install
the USB driver onto your computer.
•You need to perform this step only once, the first
time you connect to your computer.
•If you are running Windows XP, you do not need to
install the USB driver.
2. Use the USB cradle to establish a connection between
the camera and computer.
3. View and copy the images you want.
Downloaded From camera-usermanual.com Casio Manuals 
						

							VIEWING IMAGES ON A COMPUTER
152
1.What you should do first depends on whether
your computer is running under Windows 98,
Me/2000 or Windows XP.

 Windows 98/Me/2000 Users
•Start from step 2 to install the USB driver.
•Note that the example installation presented here
uses Windows 98.

 Windows XP Users
•Installation of the USB driver is not required, so jump
directly to step 6.
2.Set the bundled CD-ROM (CASIO Digital
Camera Software) into the CD-ROM drive of
your computer.
3.On the menu screen that appears, click
“English”.
4.Click [USB driver] and then [Install].
•This starts installation.
•The following steps show installation under the
English version of Windows.
 IMPORTANT! 
•If you want to transfer files from the camera’s built-in
memory to a computer, make sure there is no
memory card loaded in the camera before you place
it onto the USB cradle.
•If battery goes low while you are not using the AC
adaptor, data communication may stop and the
camera may shut down. Use of the special AC
adaptor is recommended to power the camera during
data communication.
•If you are using battery power without the AC
adaptor, make sure that the battery is fully charged.
Do not try to establish a connection between the camera
and computer before installing the USB driver onto the
computer. If you do, the computer will not be able to
recognize the camera.
•USB driver installation is required in the case of
Windows 98, Me, and 2000. Do not connect the
camera to a computer running one of the above
operating systems without installing the USB driver
first.
•USB driver installation is not required in the case of
Windows XP.
Downloaded From camera-usermanual.com Casio Manuals 
						

							VIEWING IMAGES ON A COMPUTER
153
5.On the screen that appears after installation
is complete, select the “Yes, I want to restart
my computer now.” check box and then click
[Finish] to restart your computer.
6.Connect the bundled AC adaptor to the [DC IN
5.3V] connector of the USB cradle, and then
plug it in to a household power outlet.
•If you are using battery power without the AC
adaptor, make sure that the battery is fully charged.
•Note that the shape of the AC adaptor depends on
the area where you purchased the camera.
[DC IN 5.3V]
aaaaaaaaaaaaaaaaaaaaaaaaaaa
Downloaded From camera-usermanual.com Casio Manuals 
						

							VIEWING IMAGES ON A COMPUTER
154
•Take care when connecting the USB cable to the
USB cradle or your computer. USB ports and cable
plugs are shaped for proper positioning.
•Plug the USB cable plugs into the ports securely, as
far as they will go. Proper operation is not possible if
connections are not correct.
8.In the REC mode or the PLAY mode, press the
camera’s [MENU] button.
9.Select the “Set Up” tab, select “USB”, and
then press [].
10.Use [] and [] to select “Mass Storage (USB
DIRECT-PRINT)”, and then press [SET].
11.After making sure the camera is turned off,
place the camera onto the USB cradle.
•Do not place the camera onto the USB cradle while it
is turned on.
USB port
Connector AUSB cable
(bundled)
[USB] Connector B
7.Connect the USB cable that comes bundled
with the camera to the USB cradle and your
computer’s USB port.
Downloaded From camera-usermanual.com Casio Manuals 
						

							VIEWING IMAGES ON A COMPUTER
155
13.On your computer, double-click “My
Computer”.
•If you are running Windows XP, click [Start] and then
[My Computer].
14.Double-click “Removable Disk”.
•Your computer sees the camera’s file memory as a
removable disk.
15.Double-click the “Dcim” folder.
16.Double-click the folder that contains the
image you want.
17.Double-click the file that contains the image
you want to view.
•For information about file names, see “Memory
Directory Structure” on page 163.
18.Depending on your operating system, perform
one of the following procedures to save the
files, if you want.
12.Press the USB cradle’s [USB] button.
•This will cause the “Add New Hardware...” dialog box
to appear on the computer screen as the computer
automatically detects the camera’s file memory. After
you install the USB driver, “Add New Hardware...”
dialog box will no longer appear when you perform
the above steps to establish a USB connection.
•Pressing the [USB] button enters the USB mode,
which causes the USB cradle’s [USB] lamp to light
green (page 187).
•At this point, some operating systems will display a
“Removable Disk” dialog box. If your operating
system does, close the dialog box.
[USB] button
[USB] lamp
Downloaded From camera-usermanual.com Casio Manuals 
						

							VIEWING IMAGES ON A COMPUTER
156
 IMPORTANT! 
•Never use your computer to edit, delete, move, or
rename images stored in file memory. Doing so can
cause problems with the image management data
used by the camera, which may make it impossible
to display images on the camera or it may cause a
large error in the number of images value displayed
by the camera. Always copy images to your
computer memory before performing any edit, delete,
move, or rename operation.
19.Depending on the version of Windows you are
running, use one of the following procedures
to terminate the USB connection.

 Windows Me/98/XP Users
•After pressing the USB cradle’s [USB] button and
making sure that the [USB] lamp is not lit, remove
the camera from the USB cradle.

 Windows 2000 Users
•Click card services in the task tray on your computer
screen, and disable the drive number assigned to the
camera. After pressing the USB cradle’s [USB]
button and making sure that the [USB] lamp is not lit,
remove the camera from the USB cradle. 
 Windows 98, 2000, Me
1. In the camera’s file memory (Removable Disk), right-
click the “Dcim” folder.
2. On the shortcut menu that appears, click [Copy].
3. Double click [My Documents] to open it.
4. On the My Documents [Edit] menu, click [Paste].
•This copies the “Dcim” folder (which contains the
image files) to your “My Documents” folder.

 Windows XP
1. In the camera’s file memory (Removable Disk), right-
click the “Dcim” folder.
2. On the shortcut menu that appears, click [Copy].
3. Click [Start] and then [My Documents].
4. On the My Documents [Edit] menu, click [Paste].
•This copies the “Dcim” folder (which contains the
image files) to your “My Documents” folder.
Downloaded From camera-usermanual.com Casio Manuals 
						

							VIEWING IMAGES ON A COMPUTER
157
Using the Camera with a Macintosh
Computer
The following are the general steps for viewing and copying
files from a Macintosh.
You can find details about each operation in the
procedures that follow below. Note that you should also
refer to the documentation that comes with your Macintosh
for other information about USB connections, etc.
USB Connection Precautions
•Be sure to read the documentation that comes with your
computer for other important information about USB
connections.
•Do not leave the same image displayed on your computer
screen for a long time. Doing so can cause the image to
“burn in” on the screen.
•Never disconnect the USB cable, or perform any camera
or USB cradle operation while data communication is in
progress. Doing so can cause data to become corrupted.
 IMPORTANT! 
•This camera does not support operation with a
computer running Mac OS 8.6 or lower, or Mac OS X
10.0. 
If you have a Macintosh running Mac OS 9 or
OS X (10.1, 10.2 or higher), use the standard USB
driver that comes with your OS.
1. Use the USB cradle to establish a connection between
the camera and your Macintosh.
2. View and copy the images you want.
Downloaded From camera-usermanual.com Casio Manuals 
						

							VIEWING IMAGES ON A COMPUTER
158
 IMPORTANT! 
•If you want to transfer files from the camera’s built-in
memory to a computer, make sure there is no
memory card loaded in the camera before you place
it onto the USB cradle.
1.Connect the bundled AC adaptor to the [DC IN
5.3V] connector of the USB cradle, and then
plug it in to a household power outlet.
•If you are using battery power without the AC
adaptor, make sure that the battery is fully charged.
•Note that the shape of the AC adaptor depends on
the area where you purchased the camera.
[DC IN 5.3V]
aaaaaaaaaaaaaaaaaaaaaaaaaaa
Downloaded From camera-usermanual.com Casio Manuals 
						

							VIEWING IMAGES ON A COMPUTER
159
USB port
Connector AUSB cable
(bundled)
[USB] Connector B
2.Connect the USB cable that comes bundled
with the camera to the USB cradle and your
computer’s USB port.
•Take care when connecting the USB cable to the
USB cradle or your computer. USB ports and cable
plugs are shaped for proper positioning.
•Plug the USB cable plugs into the ports securely, as
far as they will go. Proper operation is not possible if
connections are not correct.
3.In the REC mode or the PLAY mode, press the
camera’s [MENU] button.
4.Select the “Set Up” tab, select “USB”, and
then press [].
5.Use [] and [] to select “Mass Storage (USB
DIRECT-PRINT)”, and then press [SET].
6.After making sure the camera is turned off,
place the camera onto the USB cradle.
•Do not place the camera onto the USB cradle while it
is turned on.
[USB] button
[USB] lamp
Downloaded From camera-usermanual.com Casio Manuals 
						

							VIEWING IMAGES ON A COMPUTER
160
7.Press the USB cradle’s [USB] button.
•Pressing the [USB] button enters the USB mode,
which causes the USB cradle’s [USB] lamp to light
green (page 187).
8.Your Macintosh will see the camera’s file
memory as a drive.
•The appearance of the drive icon depends on the
Mac OS version you are using.
•After installing the USB driver, your Macintosh will
see the camera’s file memory as a drive whenever
you establish a USB connection between them.
9.Double-click the drive icon for the camera’s
file memory, the “DCIM” folder, and then the
folder that contains the image you want.
10.Double-click the file that contains the image
you want to view.
•For information about file names, see “Memory
Directory Structure” on page 163.
11.To copy all the files in file memory to your
Macintosh hard disk, drag the “DCIM” folder
to the folder to which you want to copy it.
 IMPORTANT! 
•Never use your computer to edit, delete, move, or
rename images stored in file memory. Doing so can
cause problems with the image management data
used by the camera, which may make it impossible
to display images on the camera or it may cause a
large error in the number of images value displayed
by the camera. Always copy images to your
computer memory before performing any edit, delete,
move, or rename operation.
12.To terminate the USB connection, drag the
drive icon that represents the camera to
Trash. After pressing the USB cradle’s [USB]
button and making sure that the [USB] lamp is
not lit, remove the camera from the USB
cradle.
Downloaded From camera-usermanual.com Casio Manuals