Casio Exilim EX H20G User Manual

							91Using the Hybrid-GPS
Using the Hybrid-GPS
In addition to conventional Global Positioning System (GPS) system capabilities that 
determine your current location and time based on radio waves it picks up from GPS 
satellites, your EXILIM camera also features a built-in independent motion sensor 
employing autonomous positioning technology that uses a 3-axis bearing sensor and 
a 3-axis accelerometer. These two capabilities combine to create a Hybrid-GPS that 
provides position information (latitude and longitude), even indoors, underground, 
and in areas where GPS satellite waves cannot be received.
The Hybrid-GPS supports all of the following capabilities.
• Recording current location information (latitude, longitude, camera aiming 
direction) with image data (snapshots and movies)
• Recording current location name with image data (snapshots and movies)
• Direct stamping of the recording location name in an image (snapshots)
• Display of recorded images and location on a map
• When traveling, searching for photogenic spots near your current location
• Tracking your movements on a map
• Automatic updating of the camera’s clock based on GPS satellite wave data
A Global Positioning System (GPS) uses radio waves sent from GPS satellites 
orbiting the Earth to calculated positions anywhere on the globe. Signals from GPS 
satellites can be used to determine a person’s current location and the current time 
at that location.
Downloaded From camera-usermanual.com Casio Manuals 
						

							92Using the Hybrid-GPS
Before using the Hybrid-GPS function for the first time, perform in the following steps 
to turn it on and receive GPS satellite waves.
1.Take the camera outside to a location where there is an unobstructed 
path to the sky above.
2.Press [ON/OFF] (Power) to turn on the camera and then press [MENU].
3.On the “Set Up” tab, select “GPS” and then press [6].
4.Use [8] and [2] to select “On” and then press [SET].
5.Wait until the GPS wave condition icon (page 93) changes to  ,   
(GPS satellite waves being received).
IMPORTANT!
• When “On” is selected for the “GPS” setting, the camera’s GPS function continues 
to operate and periodically perform positioning, even when the camera is turned 
off. Whenever you are instructed to turn off all digital devices, such as during 
aircraft takeoffs and landings, be sure to change the camera’s “GPS” setting to 
“Off” and then turn off the camera.
NOTE
• The first GPS satellite receive operation may take more time than normal.
• When “On” is selected for the “GPS” setting, the camera will continually acquire 
position data (latitude, longitude) while turned on, and intermittently acquire 
position data while turned off.
Recording Current Location Information (Latitude, Longitude, 
Direction, Place Name) with Image Data
Enabling the GPS Function (GPS)
Downloaded From camera-usermanual.com Casio Manuals 
						

							93Using the Hybrid-GPS
While “On” is selected for the “Record Lat/Long” setting, location information (latitude, 
longitude, camera aiming direction) as measured by the Hybrid-GPS will be recorded 
along with the image data (snapshots and movies).
1.In the REC mode, press [MENU].
2.On the “Set Up” tab, select “Record Lat/Long” and then press [6].
3.Use [8] and [2] to select “On” and then press [SET].
4.Press the shutter button (if you are shooting a snapshot) or [0] (Movie) 
(if you are shooting a movie).
This will record the image along with the location information (latitude, longitude, 
direction) for your current location.
• In the case of a snapshot, the location information is recorded when you press 
the shutter button all the way down. For a movie, the location information is 
recorded when you press [0] (Movie).
.Checking GPS Wave Conditions
An icon on the display shows current GPS wave conditions. Be sure to check this 
icon before recording an image.
Recording Location Information with Image Data 
(Record Lat/Long)
IconGPS Wave Conditions
GPS satellite waves being received. GPS measurement location 
information can be recorded with image data.
GPS satellite wave reception is poor, so GPS measurement location 
information cannot be recorded with image data. In this case, motion 
sensor location information will be recorded with image data.
GPS satellite waves cannot reach your location, so GPS position 
information cannot be recorded with an image. The camera can, however, 
save position information produced by the motion sensor.
GPS is turned off (page 92).
Downloaded From camera-usermanual.com Casio Manuals 
						

							94Using the Hybrid-GPS
NOTE
• You can delete recorded latitude, longitude, and direction data as required (page 
109).
• Recorded latitude, longitude, and direction data cannot be edited.
• Shooting an image while on the move may result in incorrect position information 
being registered with the image.
• The current “Record Lat/Long” setting is ignored while “Off” is selected for the 
“GPS” setting (page 92).
• Note that location information recording is turned on under initial factory default 
settings. If you do not want latitude, longitude, and direction data recorded with 
image data, be sure to change the “Record Lat/Long” setting to “Off”.
• Location information is recorded along with any snapshots and movies you shoot 
while “On” is selected for “Record Lat/Long”. Remember that when you hand such 
image data over to another person or publish it on the Internet or via any other 
electronic means, the location information is included with the image data you hand 
over or publish. If you do not want location information made public with your 
image, use the “Delete Site Info” command (page 109) to delete it from the image, 
or do not record location information when you shoot the original snapshot or 
movie.
You can select from among approximately 1 million place names (country names, 
landmark names) in camera memory and insert one into your image data (snapshots 
and movies).
1.In the REC mode, point the camera at the 
subject.
Based on the measurement of your current location 
(latitude and longitude), the camera will display a 
candidate place name (country name, landmark 
name).
2.Use [4] and [6] to select the place name you want to insert into the 
image data.
• There can be up to six candidates for a place name.
• No place name will be inserted when “– – –” (blank) is displayed for the place 
name.
• If you select “– – –” (blank), the place name candidate display will disappear 
from the display after about two seconds. Pressing [4] or [6] at this time will 
cause the place name candidate display to reappear.
• If a place name is too long to fit on the display, it will scroll on the display.
3.Press the shutter button (if you are shooting a snapshot) or [0] (Movie) 
(if you are shooting a movie).
This will record the image along with the place name.
Inserting the Place Name into Image Data (Insert Place)
Place name display
Downloaded From camera-usermanual.com Casio Manuals 
						

							95Using the Hybrid-GPS
.About place names
• Place name candidates are those selected from among the country and landmark 
names in camera memory based upon current latitude and longitude 
measurements.
• “– – –” will be shown in place of the candidates if there is no appropriate place 
name at your current latitude and longitude.
• Note that displayed place names are not precise and are meant as general 
suggestions only. Certain conditions may result in the suggestion of incorrect place 
name candidates.
• Some landmark names may not match the proper formal name of a landmark.
• There is no guarantee that a place name desired by you is included in the names 
included in camera memory.
• Shooting an image while on the move may result in incorrect place names being 
displayed as candidates.
• Insertion of a place name is not supported while “Off” is selected for the “GPS” 
setting (page 92).
NOTE
• You can delete inserted place name data from images as required (page 109).
• Inserted place name data cannot be edited (page 94).
Downloaded From camera-usermanual.com Casio Manuals 
						

							96Using the Hybrid-GPS
You can use this procedure to select from among the place names (country names, 
landmark names) in camera memory and stamp a place directly into the image 
(snapshots).
IMPORTANT!
• Unlike place name insertion, once a place name is stamped into a snapshot, it 
cannot be edited or deleted.
1.In the REC mode, press [MENU].
2.On the “Set Up” tab, select “Stamp Place” and then press [6].
3.Use [8] and [2] to select “On” and then press [SET].
4.Point the camera at the subject and then use the same procedure as 
that under “Inserting the Place Name into Image Data (Insert Place)” 
(page 94) to select a place name.
5.Press the shutter button to shoot.
This will record the image with the place name stamped in it.
NOTE
• Place name stamping is disabled when certain BEST SHOT scenes are being 
used.
• Shooting an image while on the move may result in the incorrect place name being 
stamped into the image.
• Insertion of a place name is not supported while “Off” is selected for the “GPS” 
setting (page 92).
Stamping the Place Name into an Image (Stamp Place)
Downloaded From camera-usermanual.com Casio Manuals 
						

							97Using the Hybrid-GPS
• Better GPS satellite wave reception can be attained by 
holding the camera still with the GPS antenna pointed 
towards the sky.
• Since GPS satellites are constantly moving, your location, 
the time of day, and other conditions may cause it to take 
some time before positioning can be performed. In some 
cases, positioning may not be possible.
• Good reception is not possible in the locations listed below due to blockage or 
reflection of GPS satellite waves. For good wave reception, move outside where 
there is an unobstructed path to the sky above.
– Inside of a building or underground
– Among high-rise buildings
– Under an overhead structure
– Inside of a tunnel
– Near high-voltage wires
– Inside of dense foliage
• When carrying the camera around, do not place it into a metal case. A metal 
enclosure makes it impossible for the camera to receive GPS satellite waves.
• Nearby magnetic and metal can cause sensor errors. Keep the camera as far away 
as possible from magnets and metal.
• Nearby mobile phones and other devices that use the 1.5GHz band radio waves 
can interfere with the camera’s GPS satellite wave reception.
• Depending on wave conditions, GPS satellite positioning is subject to error of 
hundreds of meters.
• When you are in a location where the camera is unable to receive GPS satellite 
waves, positioning accuracy may be relatively lower than in locations where waves 
can be received.
• Reception may take a number of minutes the first time you perform GPS satellite 
wave reception after purchasing the camera, after the camera was continually in an 
area where satellite wave reception was impossible for a long time, or after leaving 
the camera without a battery loaded for a long time.
Precautions when Using the Hybrid-GPS 
Downloaded From camera-usermanual.com Casio Manuals 
						

							98Using the Hybrid-GPS
• The Hybrid-GPS is able to provide position information (latitude and longitude) 
even under conditions where waves cannot be received from GPS satellites. 
However, relying solely on the motion sensor for long periods where GPS satellite 
reception conditions are poor, under an underpass or on a steel bridge, or in the 
vicinity of buildings, pedestrian bridges, electrical equipment, steel desks, steel 
chairs, or other objects that generate magnetism can result in bearing, latitude, and 
longitude reading errors. In order to ensure that position information is as accurate 
as possible, it is recommended that you occasionally move to an area where there 
is an unobstructed path to the sky above to perform GPS satellite wave reception. 
The motion sensor uses GPS satellite wave reception data to calibrate its own 
data.
• The direction sensor may not be able to perform direction measurements under 
any of the following conditions.
– Immediately after “On” is selected for the “GPS” setting (page 92)
– Immediately after loading the battery and turning on the camera
• Do not operate the GPS function while operating a motor vehicle.
• The GPS function of this camera uses WGS84 (World Geodetic System 1984).
Downloaded From camera-usermanual.com Casio Manuals 
						

							99Using the Hybrid-GPS
After you press [ý] (MAP) to enter the MAP mode, you can view the map data 
stored in memory and use it to perform a variety of operations described in this 
section.
The MAP mode has two submodes described below. Each press of [ý] (MAP) 
toggles between the two submodes. Select the submode that suits your shooting 
needs.
• If you want to display images only, use the PLAY mode (page 30).
Using the Map Data Stored in Camera Memory (MAP Mode)
About the MAP mode
User Image ModeIn this mode, you can display images you shot, the locations 
where you shot them, and the direction the camera was 
pointed when you shot them on a map screen.
• Images that include position information, the locations 
where you shot them, and the horizontal direction the 
camera was pointed when you shot them are displayed on 
map screens stored in camera memory.
You also can display tracks on the map that show your 
movements.
• You can use measurement data stored in camera memory 
to display tracks of your movements on maps stored in 
camera memory.
Photogenic Spot 
ModeThis mode lets you use the on-screen map to find the locations 
of tourist attractions, picturesque scenery, and other 
photogenic spots around the world.
• The camera’s memory contains data on a total of 
approximately 10,000 tourist attractions, picturesque 
scenery, and other photogenic spots around the world. This 
makes it possible for you to easy locate nearby once-in-a-
lifetime photo opportunities, making your travels more 
exciting and rewarding.
Downloaded From camera-usermanual.com Casio Manuals 
						

							100Using the Hybrid-GPS
.User Image Mode
The User Image Mode screen shows images that you shot on the map screen, along 
with icons and numbers that provide a wealth of information.
1Zoom bar
Shows the current scale/position and 
scale/position range of the currently 
displayed map.
2Mode icon
Indicates the current mode (REC, 
PLAY, User Image, Photogenic 
Spot).
3Orientation icon
Indicates the current map orientation 
(north).
4Current time
Indicates the current time.
• The format (24-hour format or 
12-hour format) of the time is in 
accordance with the current 
“Adjust” Setting.
5Image cursor
The cursor is a frame around a user 
image that indicates which image is 
currently selected.
• The user image mark for the image 
that is selected with the cursor will 
flash on the map.
6Image list
Lists the images (user images) that 
were recorded on the currently 
displayed map.
• The user image list shows images 
in the sequence starting from the 
user image mark that is closest to 
the center of the radar screen, and 
then radiates outwards in a 
clockwise direction.
7Distance
Indicates the straight-line distance 
from the center of the radar screen to 
the currently flashing user image 
mark.
8Current location icon
 indicates your current location.
• The color of the figure indicates the 
current GPS positioning condition 
(green indicating GPS positioning, 
gray for non-GPS positioning).
9Place name
Shows the place name registered 
along with a shot image (user image).
• If there is not enough space to 
show the entire name, it will scroll 
on the display.
bkScale
Shows the scale of the map.
blPosition information log
You can display the position 
information log to track your 
movements over time.
bmRadar screen lines
A cross in the center and concentric 
circles radiating outwards on the map 
provide references for distance and 
locations.
MAP Mode Monitor Screen Content
78 12345
6
9 bobn
bk bl
bm
B
Downloaded From camera-usermanual.com Casio Manuals