Casio EX S10 User Manual

							71Advanced Settings
Procedure
[r] (REC) * [MENU] * Quality Tab * Contrast
You can specify one of five contrast settings from +2 (most contrast between light and 
dark) to –2 (least contrast between light and dark).
Procedure
[r] (REC) * [MENU] * Quality Tab * Flash Intensity
You can specify one of five flash intensity settings, from –2 (weakest) to +2 
(strongest).
• Flash intensity may not change when the subject is too far away or too close.
Procedure
[r] (REC) * [MENU] * Quality Tab * Flash Assist
The subject in an image will look 
too dark if flash intensity is not 
enough to reach a subject that is 
too far away. When this happens, 
you can use flash assist to 
supplement the brightness of the 
subject so it appears as if flash 
illumination was sufficient. Select 
“Auto” to turn on Flash Assist.
Adjusting Image Contrast (Contrast)
Specifying Flash Intensity (Flash Intensity)
Turning On Flash Assist (Flash Assist)
Flash assist turned offFlash assist turned on 
						

							72Viewing Snapshots and Movies
Viewing Snapshots and Movies
See page 19 for the procedure for viewing snapshots.
1.Press [p] (PLAY) and then use [4] and [6] to display the movie you 
want to view.
2.Press [SET] to start 
playback.
Movie Playback Controls
• Playback may not be possible for movies not recorded with this camera.
Viewing Snapshots
Viewing a Movie
Fast forward/
fast reverse[4] [6]
• Each press of either button increases the speed of the fast 
forward or fast reverse operation.
• To return to normal playback speed, press [SET].
Play/pause[SET] 
1 frame 
forward/back[4] [6]
• Holding down either button scrolls continuously.
Volume 
adjustmentPress [2] and then press [8] [2]
• Volume can be adjusted only while movie playback is in 
progress.
Information 
display on/off[8] (DISP) 
ZoomSlide the zoom controller in the direction of z ([).
• You can use [8], [2], [4], and [6] to scroll the zoomed image 
on the monitor screen. You can zoom a movie image up to 4.5 
times normal size.
Stop playback[MENU] 
Movie icon: »
Image quality Recording time 
						

							73Viewing Snapshots and Movies
1.In the PLAY mode, use [4] and [6] to scroll through the images until 
the one you want is displayed.
2.Slide the zoom controller towards z ([) to 
zoom.
You can use [8], [2], [4], and [6] to scroll the 
zoomed image on the monitor screen. Slide the 
zoom controller towards w to unzoom the image.
– If display indicators are turned on, an indicator 
in the lower right corner of the monitor screen 
shows what part of the zoomed image is 
currently displayed.
– To exit the zoom screen, press [MENU] or [BS] 
(^).
– Though the maximum image zoom factor is 
8X, certain image sizes may not allow zooming 
up to the full 8X.
1.In the PLAY Mode, slide the zoom controller 
towards w (]).
Use [4] and [6] to scroll, 12 images at a time.
To view a particular image, use [8], [2], [4], or [6] 
to move the selection boundary to the image you 
want and then press [SET].
Zooming an On-screen Image
Displaying 12 Images on the Same Screen
Image area
Current display area
Zoom factor
Boundary 
						

							74Viewing Snapshots and Movies
1.In the PLAY Mode, slide the zoom controller towards w (]) twice.
This will display the calendar screen that shows the first image recorded on each 
day.
To display the first image recorded on a particular 
day, use [8], [2], [4], and [6] to move the selection 
boundary to the day you want and then press [SET].
To exit the calendar screen, press [MENU] or [BS] 
(^).
• If you save an image using any one of the 
following functions, the image will appear in the 
calendar on the date that you last saved it.
Dynamic Range, White Balance, Brightness, Keystone Correction, Color 
Restoration, Resizing, Cropping, Copy, Layout Print, MOTION PRINT
If you edit the date and time of an image, the image still will appear on the date 
it was originally recorded.
1.With the camera turned off, hold down [4] and [p] (PLAY) until the 
Image Roulette screen appears on the monitor screen.
The Image Roulette screen will cycle randomly through all the snapshots that are 
currently in memory and finally stop at one.
• To perform the Image Roulette operation again, press [4] or [6].
• To exit the Image Roulette screen, press [r] (REC) to enter the REC Mode or 
[ON/OFF] to turn off the camera.
• For a rotated snapshot (page 87), the Image Roulette screen shows the 
unrotated version.
• The camera will exit Image Roulette automatically if you do not perform the 
next Image Roulette operation within about one minute after the final image of 
the previous operation appears on the monitor screen.
• Note that Image Roulette works only with images shot with this camera. Image 
Roulette may not operate properly when other types of images are in memory.
• You can use Image Roulette only when [r] (REC) and [p] (PLAY) 
operations (page 130) are configured for “Power On” or “Power On/Off”.
Displaying Images in the Calendar Screen
Using Image Roulette  
						

							75Viewing Snapshots and Movies
1.Use the AV cable that comes with the camera to connect it to the TV.
• Make sure that you insert the cable connector into the USB/AV port until you 
feel it click securely into place. Failure to insert the connector fully can result in 
poor communication or malfunction.
• Note that even while the connector is fully inserted, you still 
will be able to see the metal part of the connector as shown 
in the illustration.
2.Turn on the TV and select its video input mode.
If the TV has more than one video input, select the one where the camera is 
connected.
3.Press [p] (PLAY) to turn on the camera.
This will cause an image to appear on the TV screen, without anything appearing 
on the camera’s monitor screen.
• Pressing [ON/OFF] or [r] (REC) will not turn on the camera while the AV 
cable is connected.
• You also can change the aspect ratio of the screen and the video output 
system (page 131).
4.Now you can display images and play back movies as you normally do.
Viewing Snapshots and Movies on a TV Screen 
TVYellowAV cable (bundled)
USB/AV port White
Making sure that the 2 mark on the camera is aligned 
with the 8 mark of the AV cable connector, connect 
the cable to the camera.Audio Video
VIDEO IN jack (yellow)AUDIO IN jacks (white) 
						

							76Viewing Snapshots and Movies
NOTE
• Audio is monaural.
• Certain TVs may cut off part of the images.
• Before connecting to a TV to display images, be sure to configure the camera’s 
[r] (REC) and [p] (PLAY) buttons for “Power On” or “Power On/Off” (page 130).
• Audio is initially output by the camera at maximum volume. When you first start 
displaying images, set the TV volume control at a relatively low level and then 
adjust it as required.
• All icons and indicators that appear on the monitor screen also appear on the TV 
screen. You can use [8] (DISP) to change the display contents.
Recording Camera Images to a DVD Recorder or Video Deck
Use one of the following methods to connect the camera to the recording device 
using the camera’s bundled AV cable.
– DVD recorder or video deck: Connect to the VIDEO IN and AUDIO IN terminals.
– Camera: USB/AV port
You can play a slideshow of snapshots and movies on the camera and record it on a 
DVD or video tape. You can record movies by selecting “» Only” for the slideshow 
“Images” setting (page 77). When recording images to an external device, use [8] 
(DISP) to clear all indicators from the monitor screen (page 123).
For information about connecting a monitor to the recording device and about how to 
record, see the user documentation that comes with the recording device you are 
using. 
						

							77Other Playback Functions (PLAY)
Other Playback Functions (PLAY)
This section explains menu items that you can use to configure settings and perform 
other playback operations.
Procedure
[p] (PLAY) * [MENU] * PLAY Tab * Slideshow
For information about menu operations, see page 56.
Playing a Slideshow on the Camera (Slideshow)
StartStarts the slideshow
ImagesSpecifies the type of images to be included in the slideshow
All images: Snapshots, movies, and audio recordingsT Only: Snapshots and audio snapshots only
» Only: Movies only
One Image: One single selected image (selected using [4] and [6])
TimeTime from the start to the end of the slideshow
1 to 5 minutes, 10 minutes, 15 minutes, 30 minutes, 60 minutes
IntervalAmount of time each image remains displayed
Use [4] and [6] to select a value from 1 to 30 seconds, or “MAX”.
If you specify a value from 1 to 30 seconds, images change at the 
specified interval, but the audio portion of movies and audio snapshots 
will continue to play until the end.
When the slideshow reaches a movie file while “MAX” is selected, only 
the first frame of the movie will displayed. Voice Recording files are not 
played back when “MAX” is selected.
EffectSelect the effect you want.
Pattern 1 to 5: Plays background music and applies an image change 
effect.
• Patterns 1 through 4 have different background music, but they all 
use the same image change effect.
• Pattern 5 can be used for playback of snapshots only, and the 
“Interval” setting is ignored.
• The currently selected image change effect setting is disabled 
automatically in following cases.
– When playing a slideshow for which “» Only” or “One Image” is 
selected for the “Images” setting
– When the interval setting is 1 second or 2 seconds.
– Before and after playback of a movie or Voice Recording file
Off: No image change effect or background music 
						

							78Other Playback Functions (PLAY)
• To stop the slideshow, press [SET]. Pressing [MENU] instead of [SET] stops the 
slideshow and returns to the menu screen.
• Adjust audio volume by pressing  [2] and then press [8] or [2] during playback.
• All button operations are disabled while the slideshow is transitioning from one 
image to another.
• The time required for transition from one image to another may be longer in the 
case of an image that was not recorded with this camera.
You can replace the built-in slideshow background music with other music from your 
computer.
Supported File Types:
• IMA-ADPCM format WAV files
• Sampling Frequencies: 22.05 kHz/44.1 kHz
• Quality: Monaural
Number of Files: 9
File names: SSBGM001.WAV to SSBGM009.WAV
• Create the music files on your computer using the above names.
• Regardless of which effect pattern you select, the BGM files you store in camera 
memory are played back in name sequence.
1.Connect the camera to your computer (pages 101, 111).
If you plan to save the music files to the camera’s memory card, make sure the 
card is loaded in the camera.
2.Perform one of the following operations to open the memory card or 
built-in memory.
This will cause the camera to be recognized by your computer as a Removable 
Disk (Drive).
• Windows
1Windows XP: Start * My Computer
Windows Vista: Start * Computer
Windows 2000, Me, 98SE, or 98: Double-click “My Computer”.
2Double-click “Removable Disk”.
•Macintosh
1Double-click the camera’s drive icon.
3.Create a folder named “SSBGM”.
Saving Music from Your Computer to Camera Memory
C 
						

							79Other Playback Functions (PLAY)
4.Double-click the “SSBGM” folder you created and copy the 
background music file to it.
• See the user documentation that comes with your computer for information 
about moving, copying, and deleting files.
• If there are background music files both in built-in memory and on the memory 
card loaded in the camera, the files on the memory card take priority.
• See page 115 for information about camera folders.
5.Disconnect the camera from the computer (pages 102, 111).
Procedure
[p] (PLAY) * [MENU] * PLAY Tab * Layout Print
You can use the following 
procedure to insert existing 
snapshots into the frames of a 
layout and produce a new image 
that contains multiple snapshots.
1.Use [4] and [6] to select 
the layout pattern you 
want and then press 
[SET].
2.Use [4] and [6] to select the background color and then press [SET].
3.Use [4] and [6] to select the images you want to include in the layout 
then press [SET].
4.Press [SET] and repeat step 3 for the remaining frames in the layout.
The final layout image will be saved after you insert the final snapshot into it.
Laying Out Snapshots with Layout Print (Layout Print)
Layout Pattern
(2 images)Layout Pattern
(3 images)
C 
						

							80Other Playback Functions (PLAY)
NOTE
• You will not be able to save the new image unless there is a snapshot in all of the 
layout frames.
• 3:2 and 16:9 images cannot be included in a Layout Print image.
• The recording date of the resulting Layout Print image is the recording date if the 
image you place into the final frame, not the date you create the Layout Print 
image.
• The Layout Print image is saved as 7M (3072
x2304 pixels) size.
Procedure
[p] (PLAY) * Movie Screen * [MENU] * PLAY Tab * 
MOTION PRINT
1.Use [8] and [2] to select 
either “9 frames” or “1 
frame”.
When “9 frames” is selected, 
the frame you select in step 2 
will be in the center of the 
MOTION PRINT image.
2.Use [4] and [6] to scroll through the movie frames and display the one 
you want to use as the image of the MOTION PRINT image.
Holding down [4] or [6] scrolls at high speed.
3.Press [SET].
• Only the frames of movies recorded on this camera can be used in a MOTION 
PRINT image.
Creating a Snapshot of Movie Frames (MOTION PRINT)
9 frames 1 frame