Carrier Em1 Manual

T -- 3 11 11 - 2
INSTALLATION CHECK-OUT, CONDENSER - Continued:
____ ____
Was mineral oilused to lubricate the fittings, hose and O Rings?
____ ____Was excess oil wiped from fittings and hose?
____ ____Are the Quick-Click fittings clamped to the Quick-Click refrigerant hose correctly?
____ ____Are the refrigeration hoses routed to the condenser(s) properly?
____ ____Are all the condenser fans blowing air in the proper direction?
____ ____ Is 12.5 Volts available at the condenser?
____ ____Are exposed...

T--311
11 - 3
INSTALLATION CHECK-OUT, EVAPORATOR - Continued
____ ____
Are evaporators properly grounded?
____ ____If ducted system, is ductwork properly mounted and trimmed?
____ ____Are all required grills/louvers installed in the ductwork?
REFRIGERATION HOSE AND ELECTRICAL HARNESS ROUTING:
YES NO
____ ____
Is wiring harnesses and refrigerant hoses protected from sharp edges, heat sources
and moving parts?
____ ____Are insulated clamps used to support the hose and harness? Tie-wraps should only
be used...

T -- 3 11 11 - 4
INSTALLATION CHECK-OUT, - Continued
FINAL:
Record readings after system has been running for at least 10 minutes at high idle.
System Pressure(s):Rear or Passenger Side Front or Drivers Side
Suction Pressure _____ psig Suction Pressure ____ psig
Discharge Pressure _____ psig Discharge Pressure ____ psig
Temperatures:
Ambient Temperature _____F Evaporator Air Temperature In _____ F _____ F _____ F
Evaporator Air Temperature Out _____ F _____ F _____ F
Charges:
Actual values as recorded on...

T--311
11 - 5 11.1 SYSTEM REQUIREMENTS LABEL
The system requirements label must be conveniently
located within the vehicle’s engine compartment. This
label, when properly completed by the installer, will give
the servicing technician the refrigerant and oil
charge(s), evaporator(s), condenser(s), and
compressor(s) serial numbers, the drive belt(s) number,
mount kit number, the date of installation and the
installer (See Figure 11-1).
11.1.1 System Requirement Label Completion
To complete the system...

Index-- 1 T-- 311
INDEX
A
Aesthetics, 2-1
AUXILIARY HEATER HOSE ROUTING, 4-9
B
Barrier Type Hose & Fittings, 4-1
Belt Clearance, 6-2
Blower Wheels, 2-1
Bus Headliners, 2-1
C
Cap Plugs, 2-1
CHASSIS HOSE ROUTING, 4-6
CM-- 2 AND CM-- 3 STACKED COND., 3-12
Cm-- 5 CONDENSER, 3-5
Cm-- 7, CM-- 11 ROOFTOP CONDENSER, 3-6
Component Connections, 5-1
COMPRESSOR HOSE ROUTING, 4-8
COMPRESSOR INSTALLATION, 6-4
CONDENSER HOSE ROUTING, 4-7
CONDENSERS, 1-7, 3-2
Connection Lubrication (Mineral Oil), 4-1
CONTROLS, 5-2...

Index--2 T--311
INDEX
O
Obstructions, 3-1
Oil Charge, 6-5
Oil Charge , 8-1
OPERATING INSTRUCTIONS , 5-4
P
PAG And POE Oils , 8-1
PIPING DIAGRAMS, 4-9
PRE-- INSTALLATION, 1-7
PREVENTATIVE MAINTENANCE, 3-1
PROCEDURES, 10-1
Pulley Alignment, 6-3
Q
Quick-- Click Hose & Clamps, 4-1
R
R134a Charge, 8-1
REAR MOUNTED EVAPORATORS, 2-2
Requirements Label, 1-1
ROOFTOP CONDENSER HOSE ROUTING, 4-9
S
Serial Number Tags , 1-1
Service Loop, 4-1
SERVICE TOOLS, 7-1
SIDE MOUNTED EVAPORATOR, 2-9
Skirt Supports, 3-1
SKIRT...