Canon scanner imageFORMULA DR6010C User Manual

Chapter 3  Basic Operation
3-11
Scanning With the Job Function
To scan using the job function, use the following procedure.
1Place the documents into the feed tray. (See “3-3 Placing Documents,” on p. 3-5.)
2Press the job button c to start the job.
The DR-6010C monitor appears, and scanning starts.
3When scanning is complete, the image data are sent according to the preset conditions.
The message  appears on the DR-6010C monitor.
4Click [Close] to close the DR-6010C monitor.
Note
 The default setting for...

Chapter 3  Basic Operation
3-12
About Launcher
To use the Launcher feature, it is necessary to first change the Windows event settings as described 
below, and specify an application for each job button.
Note
• By default, all applications supporting the event function are enabled. If you do not change the event setting before you use the Launcher feature of the DR-6010C, the dialog box 
shown below will appear. Select an application from this dialog box or click [Cancel] and 
change the event...

Chapter 3  Basic Operation
3-13
2. Click [Devices and Printers].
Note
Under Windows Vista, click [Hardware and Sound] - [Scanners and Cameras].
Under Windows XP, click [Printers and Other Hardware] - [Scanners and Cameras].
3. Right-click [CANON DR-6010C] and click [Scan properties].
Note
Under Windows Vista/XP, select [CANON DR-6010C USB] or [CANON DR-6010C SCSI] and 
click [Proper ties].The [CANON DR-6010C USB Properties] or [CANON DR-6010C SCSI Properties] 
window appears. 

Chapter 3  Basic Operation
3-14
4. Click the [Events] tab.
2Under [Scanner events], select the button whose setting you want to change (Button No. 1, 
Button No. 2, Button No. 3.)
3By default, all applications listed under [Send to this application] are selected. Select only one 
application (deselect the check boxes for all other applications.) Then click [Apply]. 

Chapter 3  Basic Operation
3-15 IMPORTANT
If the [Disable device events] check box is selected, the Job Function cannot be used. Make 
sure that this check box is not selected.
4Click [OK] to close [CANON DR-6010C USB Properties].
5Restart Windows to enable the new event settings. 

Chapter 3  Basic Operation
3-16
3-5 CapturePerfect 3.1
This section describes the flow of the CapturePerfect 3.1 application.
For more information on CapturePerfect 3.1, see the CapturePerfect 3.1 Operation Guide and the 
CapturePerfect 3.1 online Help. Familiarize yourself with CapturePerfect 3.1 by reading these 
sources before using the application.
IMPORTANT
If you scan a document under the condition that heavily consumes the memory of your PC, 
scanning may not be performed because of insufficient...

Chapter 3  Basic Operation
3-17
„“Select Job” Settings
Scan mode settings (such as [Scan Batch to File], [Scan Batch to Printer], or [Scan Batch to Mail]) 
can be pre-registered, and then the settings can be selected for scanning by selection from the 
tool bar in a simple 2-step sequence (aÆb).
Note
The following two settings are pre-defined in the “Select Job” Settings. Up to 99 settings can 
be registered.
 Color Document 
Scan the document using 24-bit color, simplex, at 300 dpi resolution, and save...

Chapter 3  Basic Operation
3-18
Using CapturePerfect 3.1
This section describes how to start up CapturePerfect 3.1, select the scanner, and scan documents. 
The Scan Batch to File function is used here as an example.
For details, see the CapturePerfect 3.1 Operation Guide and CapturePerfect Online Help.
1Click the Windows [Start] button Æ click [Programs] ([All Programs] for Windows XP) Æ 
[CapturePerfect 3.1] Æ [CapturePerfect 3.1].
CapturePerfect 3.1 starts up.
2Follow the procedure below to select the...

Chapter 3  Basic Operation
3-19
2. Select [Canon DR-6010C] Æ click [OK].
Note
If [Canon DR-6010C] is not displayed in the list of scanners, re-install the ISIS/TWAIN driver. 
(See “2-3 Installing the Software,” on p. 2-4.)
3. Set the Default Page Size and click [OK].
Note
This dialog box is displayed only when you select [Canon DR-6010C] for the first time and 
click [OK], or when you click [Setup] for [Scanner Selection].
3On the [Scan] menu, click [Scanner Setting].
The Properties dialog box for the...

Chapter 3  Basic Operation
3-20
4Set the scan settings.
For more information on scan settings, see Chapter 7, “ISIS/TWAIN Driver Settings.”
5Place your document. (See “3-3 Placing Documents,” on p. 3-5.)
6On the [Scan] menu, select [Scan Batch to File].
The [Scan Batch to File] dialog box opens.
For more details on how to scan documents, see the CapturePerfect 3.1 Operation Guide and 
CapturePerfect Online Help.
7Specify the file name and the file type for saving the image data, and click [Save] to start...