Canon Projector WUX450 User Manual

291
Appendix
Other Information
Displayed Test Patterns
The test pattern can be displayed by pressing the TEST PATTERN button. Use this 
when there is no image signal, etc.
While the test pattern is displayed, you can use the [ ] / [ ] buttons to change to a 
different test pattern. Also, if there is an option pattern available, you can use the 
[ ] / [ ] buttons to switch pattern. A dialog box is shown during test pattern display 
that identifies the current test pattern and provides operating...

292
Supported Signal Types
This projector supports the following signal types.
If your computer or AV equipment is compatible with any one of these signal types, 
the projector’s Auto PC function selects the input signal type to project an image 
appropriately.
Analog PC
Digital PC
Resolution (dots)  Signal typeHorizontal frequency 
(kHz)Vertical frequency (Hz)
640 x 480 VGA 31.469 59.940
720 x 480 – 31.469 59.940
720 x 576 – 31.250 50.000
800 x 600 SVGA 37.879 60.317
848 x 480 – 31.020 60.000
1024 x 768...

293
Supported Signal Types
Appendix
Other Information
HDMI
Connecting to a computer
Connecting with AV equipment
Component
*1: WX520/WX450ST, *2: WUX450/WUX400ST
* The specifications in the table above are subject to change without notice.
* This projector does not support any computer output signal with a dot clock of higher than 162 MHz.
* Use a computer cable in which all pins are connected. If the cable is a type in which all pins are not 
connected, the image may not be correctly displayed.1080PsF...

294
Product Specifications
■Projector
WUX450/WX520
Model name WUX450 WX520
Display system RGB liquid crystal system
Optical systemColor separation by dichroic mirror / polarizing beam splitter 
and color composition by prism
Display device
Type Reflective liquid crystal panel
Size / Aspect ratio 0.71 x 3 / 16:10 0.70 x 3 / 16:10
Drive system Active matrix system
Number dots / Total 
number dots2,304,000 (1920 x 1200) x 
3 panels / 6,912,0001,296,000 (1440 x 900) x 
3 panels / 3,888,000
Projection lens...

295
Product Specifications
Appendix
Other Information
*1WUX450 only
*2Compliance with ISO21118-2012
WUX400ST/WX450ST
Input signal
Digital PC TMDS (Transition Minimized Differential Signaling)
Analog PC0.7Vp-p, positive polarity, impedance = 75Ω
Horizontal / vertical synchronization: TTL level, negative or 
positive polarity
Component videoCOMPONENT: Separate Y Cb/Pb Cr/Pr signal
Y: 1Vp-p, negative synchronization, impedance = 75Ω
Cb/Pb: 0.7Vp-p, impedance = 75Ω
Cr/Pr: 0.7Vp-p, impedance = 75Ω
Audio...

Product Specifications
296
*1WUX400ST only
*2Compliance with ISO21118-2012
Ratio of brightness at 
periphery to center*280%
Speaker 5W monaural x 1
Maximum input resolution 1920 x 1200 dots 1920 x 1080 dots
Video signals
Analog PC input WUXGA*1, WSXGA+, UXGA, WXGA+, SXGA+, SXGA, 
WXGA, XGA, SVGA, VGA
Digital PC input D-WUXGA*
1, D-WSXGA+, D-UXGA, D-WXGA+, D-SXGA+, 
D-SXGA, D-WXGA, D-XGA, D-SVGA, D-VGA
HDMI input From connected computers:
WUXGA*
1, WSXGA+, UXGA, WXGA+, SXGA+, SXGA, 
WXGA, XGA, SVGA, VGA...

297
Product Specifications
Appendix
Other Information
* 99.99% or more of the LCD panel pixels are effective. During projection, 0.01% or less of pixels 
may stay lit or unlit due to the characteristics of the LCD panel.
* Using the projector continuously for an extended period of time may accelerate the deterioration of 
optical parts.
■Remote control
Model number RS-RC06
Power supply DC 3.0V, using two AAA-size batteries
Operating range Approx. 8 m ±25° horizontal and vertical (to infrared remote...

Product Specifications
298
■External View
Bolt holes (M6 x 4) 
for installation of 
ceiling attachment
91.5 mm 
(3.6)
337 mm (13.3)72 mm 
(2.8)362 mm (14.3)
118 mm 
(4.6) 144.5 mm 
(5.7) 144.5 mm 
(5.7)289 mm (11.3)
33 mm (1.3)
301 mm (11.9) 370 mm (14.6)
134 mm 
(5.3)
WUX450/WX520
Bolt holes (M6 x 4) 
for installation of 
ceiling attachment
91.5 mm 
(3.6)
337 mm (13.3)72 mm 
(2.8)362 mm (14.3)
118 mm 
(4.6) 144.5 mm 
(5.7) 144.5 mm 
(5.7)289 mm (11.3)
33 mm (1.3)
301 mm (11.9) 415 mm (16.3)
134 mm...

299
Product Specifications
Appendix
Other Information
■ANALOG PC-2 / COMPONENT terminal
This terminal is used as a computer ANALOG PC input or COMPONENT input 
terminal. Use a D-sub computer cable.
The terminal specifications for the ANALOG PC input and COMPONENT input are 
the same.
Mini D-sub 15-pin
■Service Port (CONTROL)
Pin assignment
Communication format
Communication mode : RS-232-C, asynchronous, half-duplex communication
Communication speed : 19200bps
Character length : 8 bits
Stop bits : 2...

Product Specifications
300
Control commands
Commands ASCII representation Binary representation
Power supplyPower on POWER=ON 50h 4Fh 57h 45h 52h 3Dh 4Fh 4Eh 0Dh
Power off POWER=OFF50h 4Fh 57h 45h 52h 3Dh 4Fh 46h 46h 
0Dh
Power status 
acquisitionGET=POWER47h 45h 54h 3Dh 50h 4Fh 57h 45h 52h 
0Dh
Input sourceHDMI INPUT=HDMI49h 4Eh 50h 55h 54h 3Dh 48h 44h 4Dh 
49h 0Dh
Digital PC INPUT=D-RGB49h 4Eh 50h 55h 54h 3Dh 44h 2Dh 52h 
47h 42h 0Dh
Analog PC-1 INPUT=A-RGB149h 4Eh 50h 55h 54h 3Dh 41h 2Dh 52h 
47h 42h...