Canon projector REALiS SX7 Maprojector Rk II User Manual

							61
PROJECTING AN IMAGE FROM THE COMPUTER
Setting Up the Power Management Function
You can use the power management function that turns off the lamp if the projector
receives no signal input for a while.
If you enable the power management mode, the projector displays a countdown timer if the
projector is receiving no signal input and is not operated for 30 seconds, and approxi-
mately 5 minutes later the lamp is turned off and the projector goes into the power man-
agement mode.
You can select one of the following power management modes from the menu (P111).
Standby mode
Select this mode if you want to start projection soon.
In the standby mode, the lamp is turned off and cooled down. When the lamp has been
cooled down, the [POWER] indicator starts flashing in red and green to indicate it is
standby. It will start projection if the input signal is inputted or any button on the top control
or remote control is pressed.
Exit mode
Select this mode to turn off the projector automatically.
In the exit mode, the lamp is turned off and cooled down. When the lamp has been cooled
down, the [POWER] indicator stops flashing in red and stays on and the power is turned
off.
zWait until the cooling fan stops before putting the projector in the carrying bag. Do not put
the projector in the carrying bag until the cooling fan stops rotating. The projector may be
damaged due to the heat.
zAttach the lens cap to the lens to protect it and put the projector in the carrying bag.
Replace the adjustable foot to prevent the damage on the projector.
zYou can carry the projector immediately after the use (Off & Go function).
zYou can turn off the projector by disconnecting the power cord without pressing the
[POWER] button.
zThe LED illumination lamp turns on to indicate the lamp is being cooled when the power
cord is connected.
zThe projector becomes inoperative when the lamp is being cooled in a power management
mode. 
						

							Table of contents/Safety Instructions
Before Use
Setting Up the Projector
Projecting an Image from the Computer
Projecting an Image from AV Equipment
Useful Functions Available During a Presentation
Setting Up Functions from Menus
Maintenance
Troubleshooting
Appendix
Index
PROJECTING AN 
IMAGE FROM 
AV EQUIPMENT 
						

							64
PROJECTING AN IMAGE FROM AV EQUIPMENT
Projecting an Image from AV Equipment
Connecting the Projector to an AV Equipment
Connect the projector and AV equipment.
Connecting to Video Terminals
zBefore connecting cables, turn off both the projector and AV equipment.
zThe above illustrations are just examples. For more detailed information, refer to the manual
for the connecting AV equipment.
About the Component Cable
The projector cannot be connected to an AV equipment only with the supplied component
cable (RCA/Mini D-sub 15-pin). Please purchase either of the following cables according to the
type of the terminal on the AV equipment:
zRCA terminal: RCA x 3/RCA x 3 cable
zD-terminal: D-terminal/RCA x 3 cable
Supplied component cable
Video output terminal
INPUT Signal: [COMPONENT] is selected automaticallyAV equipment
Projector
(RCA component terminal) (D terminal)
Commercial 
component cable
(RCA x 3)Commercial 
component cable
(D terminal/RCA x 3)
Component input terminal
(ANALOG IN-2)Supplied 
component cable
(RCA/Mini D-sub 
15-pin)
Connecting to the RCA 
component terminalConnecting to the D terminal
Supplied 
component cable
(RCA/Mini D-sub 
15-pin)Connect the RCA 
cables according 
to color code.
zGreen (Y)
zBlue (Cb/Pb)
zRed (Cr/Pr) 
						

							65
PROJECTING AN IMAGE FROM AV EQUIPMENT
SCART cable
INPUT Signal: Select [SCART] (P72)AV equipment
Projector
(SCART terminal)
Input Terminal-2 
(ANALOG IN-2)LV-CA31 cable
Digital cableYou can project digital content via the HDMI or DVI 
terminal.
Digital video 
output 
terminal
INPUT Signal: Select [DIGITAL VIDEO] (P71)AV equipment
Projector
(HDMI terminal) (DVI terminal)
Input Terminal-1 
(DIGITAL IN) Commercial HDMI adapter cable
Commercial DVI cable
zSet the input signal as [COMPONENT] by referring to Projecting an Image from the Com-
puter and 5-BNC cable if you want to connect the projector to an AV equipment using a 5-
BNC extension cable via an video control apparatus in a hall or so (P37). 
						

							66
PROJECTING AN IMAGE FROM AV EQUIPMENT
S-VIDEO cable
INPUT Signal: [S-VIDEO] is selected automati-
callyAV equipment
Projector
S-VIDEO input 
terminal
(S-VIDEO IN)Commercial S-VIDEO video cable S-VIDEO output terminal
(S-VIDEO OUT terminal)
SX7 MarkII
SX60
INPUT Signal: [VIDEO] is selected automati-
callyAV equipment
Projector
Video input
terminal
(VIDEO IN)Commercial Video cable Video output terminal
(VIDEO OUT terminal)
Video cable
SX60 SX7 MarkII
zConnect an audio cable if you want to use the projectors speaker.
(SX7 II: P67, SX60: P39) 
						

							67
PROJECTING AN IMAGE FROM AV EQUIPMENT
Connecting to AUDIO IN Terminals (SX7 II)
Connect an audio cable to the AUDIO IN terminal corresponding to the input image signal
if you want to use the projector’s speaker.
zThe speaker outputs the audio signal corresponding to the selected image signal.
zUse an audio cable without a built-in resistor. Using an audio cable with a built-in resistor
turns down the sound.
zConnect the audio cable between the AUDIO OUT terminal and an external audio-visual
equipment if you want to output the audio signal to the audio-visual equipment (P68).
zThe built-in speaker is monaural.
Audio cable
AV equipment
Projector
Commercial audio cableAUDIO OUT terminal
(RCA terminal) (Stereo mini jack)
(Stereo mini jack) (RCA/Stereo 
mini jack)
Audio input terminal
(AUDIO IN)for DEGITAL IN/ANALOG IN-1
SX7 MarkII
for ANALOG IN-2
for VIDEO IN/S-VIDEO IN
You can input an audio signal 
corresponding to 3 image 
input systems.
Connect to the AUDIO IN ter-
minal corresponding to the 
type of the input image signal. 
						

							68
PROJECTING AN IMAGE FROM AV EQUIPMENT
Connecting to AUDIO OUT Termi-
nals (SX7 II)
Connect the audio cable between the
AUDIO OUT terminal and an external audio-
visual equipment if you want to output the
audio signal to the audio-visual equipment.
Audio cable
AV equipment
Audio output terminal
(AUDIO OUT) Commercial audio cableAUDIO IN terminal
(RCA terminal) (Stereo mini jack)
(RCA/Stereo 
mini jack)(Stereo mini jack)
Projector
The audio-visual 
equipment outputs 
the audio signal 
corresponding to 
the selected image 
signal.
SX7 MarkII
zUse an audio cable without a built-in resistor. Using an audio cable with a built-in resistor
turns down the sound.
zYou can adjust the volume level of the audio signal to the audio-visual equipment with the
remote controller or the buttons on the top control of the projector.
zThe internal speaker is disabled if you input the audio cable to the AUDIO OUT terminal.
zIf you connect the projector directly to a speaker, make sure to use the amplified speaker. 
						

							69
PROJECTING AN IMAGE FROM AV EQUIPMENT
Projecting a Video Image from an AV Equipment
You can project a video image with the steps similar to those for projecting an image from a
computer.
This section provides information specific to the projection from an AV equipment.
For more detailed information for each step, refer to the corresponding page.
1Turn on the projector.   P40*
zConnect the power cord and turn on the projector.   P40
zAdjust the height of the projecting image.   P43
zSelect a display language for the first time.   P41
zAdjust the focus by performing the auto setup or the focus adjustment if you can-
not read the message due to out of focus.   P46, 51
2Prepare the AV equipment.
zTurn on the AV equipment and start playing the video image.
3Press the   button to switch the input signal.   P70
zSelect [DIGITAL VIDEO] as the input signal.
4Press the   button twice.   P70
zAdjust the input signal, focusing, keystone distortion, and so on automatically
using the auto setup function.
5Press the   button.
zSelect an appropriate image mode depending on the projecting image.   P55*
zSelect an appropriate screen mode from the [Aspect] menu.   P73, 90, 91
Turn off the projector.   P60*
zTurn off the projector and remove the power cord from the AC outlet.
* Those steps are same as those for projecting the computer screen.
For digital content video image:
Stopping projection... 
						

							70
PROJECTING AN IMAGE FROM AV EQUIPMENT
Performing the Auto Setup
With the auto setup function, a series of screen adjustment and settings, such as Auto
focus and Auto keystone is performed automatically when projecting a video image from
an AV equipment. You can start the projection only with this operation if the input signal has
been appropriately selected.
Refer to page 46 for detailed information on items adjusted by performing the auto setup.
1Select [DIGITAL VIDEO].
Perform the steps shown in the Selecting DIGITAL VIDEO section on page 71 before
performing the auto setup if you want to project a digital content video image.
Skip this step if [DIGITAL VIDEO] has been selected at the previous projection.
2Press the [AUTO SET] button.
The [Auto setup] window appears.
3Press the [AUTO SET] button again.
One or more functions highlighted in black are performed automatically.
Selecting an Input Signal
Select [DIGITAL VIDEO] among the following input signals by following the steps shown in
the Selecting DIGITAL VIDEO section below if you want to project a digital content video
image.
DIGITAL VIDEO : Digital signal Connecting with an HDMI/DVI cable or DVI digital
cable
COMPONENT : Component signal Connecting with a supplied component cable
SCART : SCART signal Connecting with a supplied SCART cable
VIDEO : Video signal Connecting with a video cable
S-VIDEO : S-VIDEO Connecting with an S-Video cable
The component, video, and S-VIDEO signals are automatically set if a cable is connected
and the input signal is confirmed.
zYou can perform this step by selecting [OK] with the [