Canon projector REALiS SX6000 Pprojector Ro AV User Manual

							181
Configuring the Network From the Computer
Installation Manual Connecting to a Networ
k
The error meanings are as shown below.
ErrorMeaning
Input error A setting outside the valid range was set on the 
setting screen.
Password setting error The set password and confirmation password did 
not match.
Invalid SMTP The SMTP server IP address has not been set.
System failed to connect SMTP 
server.Failed to connect to the SMTP server when send-
ing a test mail.
System failed to connect POP3 
server.Failed to connect to the POP3 server attempting to 
send a test mail.
System doesnt support this auth 
type.An authentication type was set which is not sup-
ported by the server.
System failed to authenticate. Authentication failed attempting to send a test mail.
The system failed to send the test 
mail.Sending of test mail failed due to a connection fail-
ure with the SMTP server or an error which does 
not ordinarily occur.
Save Failed Mismatch in settings occurred when settings were 
changed at the same time from multiple comput-
ers. 
						

							182
Setting Up the Network
■Setting Basic Information [Network]
From [Network] in the settings window, you can log into the web screen and set basic 
network information. For the setting procedure, refer to page 177. 
ItemExplanationFactory default setting
Password
User  name When logging into the web screen, 
enter the user name in 1-byte 
alphanumeric characters and 
symbols (4 -15 characters).root
New  password When logging into the web screen, 
enter the password in 1-byte 
alphanumeric characters and 
symbols (4 -15 characters).system
Confirm new password For confirmation, enter the same 
password that you entered in [New 
password].system
TCP/IP
DHCP Select whether to turn the DHCP 
function on or off. If the function is 
on, because the IP address is 
acquired from the server, it is not 
possible to enter the [IP address], 
[Subnet mask], and [Default gate-
way].OFF
IP address Enter the IP address of the projec-
tor in 1-byte numbers.192.168.254.254
Subnet mask Enter the subnet mask in 1-byte 
numbers.255.255.255.0
Default gateway Enter the default gateway IP 
address in 1-byte numbers.0.0.0.0
If settings related to TCP / IP were changed, it is necessary to disconnect and reconnect to 
the network. If the network subnet mask was changed, select [Subnet mask] in the above 
window and set the new subnet mask. 
						

							183
Setting Up the Network
Installation Manual Connecting to a Networ
k
■Setting Up Email [Mail]
From [Mail] in the settings window, you can set the items necessary to send error 
mails and test mails. For the setting procedure, refer to page 177. 
ItemExplanationFactory default setting
To: Enter the recipient address for error 
mails in 1-byte alphanumeric char-
acters and symbols (1 - 63 charac-
ters).MailUserAccount
Cc: Enter the CC address for error mails 
in 1-byte alphanumeric characters 
and symbols (1 - 63 characters).
From: Enter the sender address for error 
mails in 1-byte alphanumeric char-
acters and symbols (1 - 63 charac-
ters)[email protected]
SMTP server IP address Enter the SMTP server IP address in 
1-byte numbers.0.0.0.0
SMTP server port number Enter the SMTP server port number 
in 1-byte numbers (1 - 65535).25
SNTP server IP address Enter the SNTP server IP address in 
1-byte numbers.0.0.0.0
Time zone Select the time zone where the pro-
jector is used.(GMT) Dublin, Lisbon, 
London
Mail resend interval Enter the interval for resending mail 
when an error occurred (units: sec-
onds) within the range of 0 - 59 sec-
onds using 1-byte numbers.10
Mail resend times Enter the number of times to resend 
mail when an error occurred within 
the range of 0 - 255 using 1-byte 
numbers.3
Error report Select whether to turn the error mail 
sending function on or off. OFF 
						

							Setting Up the Network
184
■Mail Authentication Settings [Mail auth]
From [Mail auth] in the settings window, you can configure the settings for authentica-
tion of mail that is sent when an error occurs. For the setting procedure, refer to page 
177. 
ItemExplanationFactory default set-
ting
Mail  authentication Select the mail authentication method. 
If OFF is selected, the other mail 
authentication settings cannot be 
changed.OFF
User name Enter the user name to use for mail 
authentication in 1-byte alphanu-
meric characters and symbols (1 - 63 
characters).
Password Enter the password for mail authenti-
cation in 1-byte alphanumeric charac-
ters and symbols (1 - 63 characters).
Confirm password  For confirmation, enter the same 
password as you entered in [Pass-
word].
POP3 server IP address Enter the POP3 server IP address in 
1-byte numbers.0.0.0.0
POP3 server port number Enter the POP3 server port number in 
1-byte numbers (1 - 65535).110
POP before SMTP response time Enter the wait time from POP3 authen-
tication to SMTP authentication (units: 
milliseconds) using 1-byte numbers 
(0 - 9999 milliseconds).300 
						

							185
Setting Up the Network
Installation Manual Connecting to a Networ
k
■Sending a Test Mail [Send test mail]
From [Send test mail] in the settings window, you can send a test mail to the mail 
address that was set in [Mail]. The settings cannot be changed from this window.
■SNMP Settings [SNMP]
From [SNMP] in the settings window, you can configure the settings related to control 
of projectors which use SNMP (Simple Network Management Protocol). For the set-
ting procedure, refer to page 177. 
ItemExplanation
To :
The recipient address which was set from [Mail] in the settings window 
(
P183) is displayed.
Cc:
The CC address which was set from [Mail] in the settings window (P183) 
is displayed.
From:
The sender name which was set from [Mail] in the settings window 
(
P183) is displayed.
Subject:
The predetermined mail title “Canon Projector test” is displayed. 
						

							Setting Up the Network
186
■Setting Projector Information [Projector info.]
From [Projector info.] in the settings window, you can set the names and location 
names which are used to identify projectors when multiple projectors are installed on 
the network. For the setting procedure, refer to page 177. 
ItemExplanationFactory default setting
SNMP Select the SNMP function version. If OFF is 
selected, the SNMP function will be turned 
off and the other settings in this window 
cannot be changed.OFF
Receive community Enter the community name which will 
receive projector information in 1-byte 
alphanumeric characters and symbols (1 - 
15 characters).
Password Enter the community settings password in 
1-byte alphanumeric characters and sym-
bols (8 - 15 characters). This is also used 
as the password for trapping. It can be set 
only when the SNMP version is V3.
Confirm password For confirmation, enter the same password 
as you entered in [Password].
SNMP trap Select the type of error to trap. When any of 
the checkboxes is turned on, it becomes 
possible to set [Trap IP address] and [Trap 
community].OFF (no checkmarks)
Trap IP address Enter the IP address to send information to 
when trap occurs. Enter in 1-byte numbers.0.0.0.0
Trap community Enter the community name which will send 
information when trap occurs. Enter in 1-
byte alphanumeric characters and symbols 
(1 - 15 characters).
ItemExplanationFactory default setting
Projector name Enter the projector name in 1-byte alphanu-
meric characters and symbols (1 - 63 char-
acters).WUX5000 / WUX4000 / 
WX6000 / SX6000
Location Enter the projector installation location in 1-
byte alphanumeric characters and symbols 
(0 - 63 characters). 
						

							187
Setting Up the Network
Installation Manual Connecting to a Networ
k
■Setting PJLink [PJLink]
From [PJLink] in the setting window, you can set the PJLink functions which are the 
standard for projector management on a network. For the setting procedure, refer to 
page 177. For information about PJLink, refer to page 174.
ItemExplanationFactory default 
setting
PJLink Turn the PJLink function on or off. If 
OFF is selected, the PJLink func-
tion will be turned off and the other 
settings in this window cannot be 
changed.ON
PJLink authentication Select whether to turn the PJLink 
authentication function on or off. If 
OFF is selected, [Password] and 
[Confirm password] cannot be 
changed.ON
Password Enter the PJLink authentication 
password in 1-byte alphanumeric 
characters (1 - 32 characters).system
Confirm password For confirmation, enter the same 
password that you entered in 
[Password].system 
						

							188
Controlling the Projector from a Computer
When the projector is connected to a network, it is possible to control the projector from a 
computer via the network.
1Turn on the computer and projector.
2Launch a web browser, enter “http://(projector IP address)” in the address bar, and 
press the Enter key.
The password input screen appears.
The factory default IP address is “192.168.254.254”. It is possible to check the IP 
address from the projector menu.
3Enter the user name and password on the password input screen, then click OK.
The factory default user name is “root” and the password is “system”.
4The projector web screen appears in the web browser. Click [Projector control]. 
						

							Controlling the Projector from a Computer
189
Installation Manual Connecting to a Networ
k
5The projector control screen appears. The projector can be controlled from this 
screen.
6When the operations are finished, click [Back to top] to return the initial web screen.
ItemExplanation
Projector name The name of the connected projector is displayed. (P186)
IP address The IP address of the connected projector is displayed. (P182)
Refresh Refreshes the displayed contents with the most recent informa-
tion.
Power Turns projector power on or off.
Input Select an input signal and click [Apply] to change to that input 
signal. (P59)
Aspect Select an aspect and click [Apply] to change to that aspect. (P69)
Image mode Select an image mode and click [Apply] to change to that image 
mode. (P78)
Blank Switches the blank setting on or off. (P82)
Mute Switches the mute setting on or off. (P83)
Auto PC Performs Auto PC. (P62)
Information The control results and control error information are displayed at 
the top of the screen. 
						

							190
Error Mail
The messages shown in the following error list are sent when an error occurs in the pro-
jector.
Error list
* For details, contact the Canon Customer Support Center.
Errors related to 
temperatureError 
nameTemperature abnormality
Text The temperature inside the projector is too high for some reason or the 
outside air temperature is higher than the specified one.
If the problem is inside the projector, check whether the projector is 
installed and operated normally, turn off the projector to cool its inside, 
and retry projection. If the same warning occurs again, the projector 
may be defective. Contact your dealer.
Errors related to 
the lampError 
nameFaulty lamp
Text The lamp has burnt out. Replace the lamp with a new one. If the same 
warning occurs again, the lamp drive circuit may be defective. Con-
tact your dealer.
Errors related to 
the lamp coverError 
nameFaulty lamp cover
Text The lamp cover is open. Check whether the lamp cover is installed 
properly. If it is installed properly, the lamp cover detection switch may 
be defective. Contact your dealer.
Errors related to 
the cooling fanError 
nameFaulty cooling fan
Text The cooling fan or another component may be defective. Contact your 
dealer.
Errors related to 
the power supplyError 
nameFaulty power supply
Text The voltage of part of the power supply is abnormally high or any 
other problem has occurred in the power supply. Contact your dealer.
Errors related to 
the lens connec-
torError 
nameFaulty lens connector
Text The lens cable is not connected to the lens unit. Check whether the 
lens cable is connected to the lens unit properly. 
If it is connected properly, the lens connector or cable may be defec-
tive. Contact your dealer.
Errors related to 
the air filterError 
nameFaulty air filter unit
Text The air filter unit is not installed properly.
Check whether the air filter unit is installed properly. 
If it is installed properly, the air filter unit detection switch may be 
defective. Contact your dealer.
Other types of 
errorsError 
nameUnknown Error
Text Code in hexadecimal numbers*