Canon projector REALiS SX6000 Pprojector Ro AV User Manual

							131
Setting Various Functions
User’s ManualSettin
g Functions from Menus
Lens Shift Reset
[Lens shift Reset]
Resets the lens shift (P74) setting to the 
standard position.
MENU > [System settings] > [Other settings] > 
[Lens shift Reset]
MENU > [Install settings] > [Lens shift Reset]
Select [Lens shift Reset] and press the OK 
button. The following screen for confirma-
tion appears.
Use the [ ]
 / [ ] buttons to select the 
standard position, and then select OK.
 The standard position varies depending 
on the type of lens unit used. For details, 
refer to page 75.
 The position which was adjusted by lens 
shift does not change when the power is 
turned off.
HDMIComponent
Digital PCAnalog PC 
						

							Setting Various Functions
132
Extending the Menu Dis-
play Time
[Menu display time]
The setting for the menu display time can 
be extended from the normal 10 or 30 sec-
onds to 3 minutes. For the WUX5000 / 
WUX4000, if [Extended] is set, when push-
ing and holding a button on the projector or 
remote control, the same key repeat func-
tion will be enabled as when pressing a 
button repeatedly.
MENU > [System settings] > [Other settings] > 
[Menu display time]
MENU > [Install settings] > [On screen] > [Menu 
display time]
Press the OK button to accept your setting 
and then press the MENU button or EXIT 
button (WX6000 / SX6000).
 [Normal] is the factory default.
 The following display and operation are also 
changed.
*1 WUX4000
*2 WX6000 / SX6000HDMIComponent
Digital PCAnalog PC
NormalThe menu is displayed for 10 or 30 sec-
onds.
ExtendedThe menu is displayed for 3 minutes. 
Item [Normal] [Extended]The display time of the following 
screens
-MENU screen
-Input (P60)
-Zoom adjustment (P71)
-Focus adjustment (P73)
-Keystone adjustment (P76)
-Keystone reset (P77)
-D.image shift adjustment (P67, P68)
-D.image shift reset (P69)
-Aspect (P70)
-Image mode (P78)
-Volume adjustment (P83)
-Lamp mode (P119) *1
-Lens shift (P74)
-Lens shift reset (P131)
10 / 30 
seconds3 minutes
Press-and-hold operation of 
pointer buttons other than for 
[Zoom adjustment], [Focus 
adjustment], and [Lens shift]
Press-and-hold operation of VOL buttonPress-and-hold operation of the 
D.ZOOM buttonEnabled Disabled
Key repeat *2 [On] [Off] 
						

							133
Setting Various Functions
User’s ManualSettin
g Functions from Menus
Showing / Hiding the High 
Temperature Warning Icon
[Overheat Warning Display]
You can select whether or not to display 
the [High temperature warning] icon when 
the temperature inside the projector has 
increased and is approaching the overheat 
temperature.
MENU > [System settings] > [Other settings] > 
[Overheat Warning Display]
MENU > [Install settings] > [On screen] > [Over-
heat warning display]
Press the OK button to accept your setting 
and then press the  MENU button or EXIT 
button (WX6000 / SX6000).
When [On] is set, the [High temperature 
warning] icon shown below will be dis- played when the temperature inside the 
projector is abnormally high.
• [Off] is the factory default.
HDMIComponent
Digital PCAnalog PC
Off The [High temperature warning] icon is 
not displayed.
On The [High temperature warning] icon is 
displayed.
Screen 
						

							
Setting Various Functions
134
Reducing Flickering
[Deflicker]
This function adjusts the image display in 
order to reduce flickering in the projected 
image.
MENU > [System settings] > [Other settings] > 
[Deflicker]
• When deflicker is performed, the image adjustment screen is projected for approx-
imately 20 seconds.
 To cancel deflicker, press the POWER  
button.
Gamma Restore
[Gamma restore]
This function is used when changing and 
turning of the tone characteristics and ach-
romatic color is noticed over a long period 
of time.
MENU > [System settings] > [Other settings] > 
[Gamma restore]
If Gamma restore is performed, the pro-
jected image will be adjusted for a period 
of approximately 150 seconds.
 To stop Gamma restore, press the  POWER 
button or the  EXIT button (WX6000 / 
SX6000).
HDMIComponent
Digital PCAnalog PC
Off Deflicker adjustment is not per-
formed.
Adjust Select [Deflicker] to adjust. The fol-
lowing screen appears.
OK Deflicker is performed.
Cancel Deflicker is not performed.
 Deflicker is a function that decreases 
flickering. However, there are some 
cases that flickering continues.
 Deflicker can only be used when the  lamp has been on for approximately 
30 minutes or longer.
HDMIComponent
Digital PCAnalog PC
Off Returns to the factory default with-
out performing Gamma restore.
Adjust Performs Gamma restore and 
applies the result.
OK Gamma Restore is per-
formed.
Cancel Gamma Restore is not 
performed.
 If Gamma restore is performed, the 
tone characteristics and achromatic 
color will be restored as close as 
possible to the condition when the 
unit was purchased, however it is not 
possible to restore it completely to 
the original condition. So the chang-
ing and turning color cannot be elim-
inated completely.
 Gamma restore can only be used 
when the lamp has been on for 
approximately 30 minutes or longer. 
						

							135
Setting Various Functions
User’s ManualSettin
g Functions from Menus
Lamp Warning Display
[Lamp warning display]
A message that advises you to change the 
lamp can be set to display when the lamp 
has been used for the specified period of 
time.
MENU > [Install settings] > [On screen] > [Lamp 
warning display]
Press the OK button to accept your setting 
and then press the MENU button or EXIT 
button (WX6000 / SX6000).
 The factory default is [On].
 Regardless of the [Lamp warning display] 
setting, when the lamp replacement time has 
been reached, the LAMP indicator on the 
projector will flash.
Resetting the Lamp 
Counter
[Lamp counter]
You can reset the lamp counter that indi-
cates the time for lamp replacement.
MENU > [System settings] > [Other settings] > 
[Lamp counter]
MENU > [System settings] > [Other settings] > 
[Lamp counter]
HDMIComponent
Digital PCAnalog PC
OffThe lamp warning display is not 
displayed.
OnThe prepare lamp message and 
the lamp warning display are dis-
played.HDMIComponent
Digital PCAnalog PC
Do not reset the lamp counter except
when you have replaced the lamp.
Otherwise, the lamp counter cannot
indicate the correct timing for replac-
ing the lamp.
For details of lamp replacement, refer
to page 195. 
						

							Setting Various Functions
136
Select [Lamp counter] and press the OK 
button to display the lamp counter.
Select [Reset] and press the OK button.
Select [OK] on the screen for confirmation 
and press the OK button to reset the lamp 
counter.
Press the MENU button or EXIT button 
(WX6000 / SX6000).
■About the Display of the Lamp 
Counter
The lamp counter displays the hours of 
use of the lamp in the following way.
Less than 2,700 hours
Displayed as a green bar.
2,700 hours to less than 3,000 hours
Displayed as a green and yellow bar.When the lamp hours are 2,700 hours to 
less than 3,000 hours, the message 
“Obtain a new lamp.” appears when 
power is turned on.
Over 3,000 hours
Displayed as a green, yellow and red 
bar.
The message “Replace with the new 
lamp.” appears when power is turned on. 
						

							137
Setting Various Functions
User’s ManualSettin
g Functions from Menus
Filter Warning Display
[Filter warning display]
A message advising you to perform clean-
ing can be set to display when the filter 
needs cleaning.
MENU > [Install settings] > [On screen] > [Filter 
warning display]
Press the OK button to accept your setting 
and then press the MENU button or EXIT 
button (WX6000 / SX6000).
 The factory default is [On].
Resetting the Air Filter 
Counter
[Filter counter]
This resets the counter which reminds you 
of the time for cleaning and replacing the 
air filter.
MENU > [System settings] > [Other settings] > 
[Filter counter]
If the OK button is pressed on [Filter 
counter], the air filter counter is displayed.
Select [Reset] and press the OK button.
[OK] is selected on the confirmation 
screen and the OK button is pressed, the 
air filter counter is reset.
Press the MENU button or EXIT button 
(WX6000 / SX6000).
HDMIComponent
Digital PCAnalog PC
OffThe filter warning display is not 
displayed.
OnThe filter warning display is dis-
played.HDMIComponent
Digital PCAnalog PC
For details about how to replace or 
clean the filter, refer to page 193. 
						

							Setting Various Functions
138
Displaying Test Pattern
[Test pattern]
A test pattern for checking the resolution 
and color when installing the projector can 
be displayed.
MENU > [Install settings] > [Test pattern]
Press the OK button to accept your setting 
and then press the MENU button or EXIT 
button (WX6000 / SX6000).
 The factory default is [Off].
 While the test pattern is displayed, you can 
use the 
[] / [] buttons to change to a dif-
ferent test pattern. Also, if a test pattern has 
option settings, you can change the settings 
using the 
[] / [] button. (P217)
 The test pattern can also be displayed or 
turned off by pressing the TEST PATTERN 
button on the remote control.
HDMIComponent
Digital PCAnalog PC
OffThe test pattern is not displayed.
OnThe test pattern is displayed.
The following functions in the [Image 
adjustment] tab are not applied to the 
test pattern.
 Brightness adjustment function 
(P111)
 Contrast adjustment function (P112)
 Sharpness adjustment function 
(P113)
 Color level adjustment function 
(P114)
 Color balance adjustment function 
(P114) 
						

							139
Setting Various Functions
User’s ManualSettin
g Functions from Menus
Selecting Audio In Termi-
nal
[Audio in terminal select]
You can select the audio in terminal that is 
used for each input signal (HDMI, Digital 
PC, Analog PC-1, Analog PC-2, Compo-
nent).
MENU > [Install settings] > [Audio in terminal 
select]
Press the OK button to accept your setting 
and then press the  MENU button or EXIT 
button (WX6000 / SX6000).
• The factory default is as follows.
HDMI: HDMI
Digital PC: Audio in 2
Analog PC-1: Audio in 1
Analog PC-2: Audio in 2
Component: Audio in 1
Locking Installation 
Related Functions
[Positional lock]
Operation of installation related functions 
can be prohibited.
MENU > [Install settings] > [Positional lock]
Press the  OK button to accept your setting 
and then press the  MENU button or  EXIT 
button (WX6000 / SX6000).
 The factory default is [Off].
 The positional lock can be applied to Test 
pattern display, Screen aspect settings, Key-
stone adjustment, Digital image shift adjust-
ment, Image flip H/V, Focus adjustment, 
Zoom adjustment, Lens shift adjustment and 
Lens shift reset.
HDMIComponent
Digital PCAnalog PC
Off No audio is output.
Audio in 1 Outputs the audio signal that 
is inputted in Audio in terminal 
 1.
Audio in 2 Outputs the audio signal that 
is inputted in Audio in terminal 
 2.
HDMI Outputs the HDMI audio sig-
nal. (Only for HDMI)
HDMIComponent
Digital PCAnalog PC
Off The positional lock is not used.
On Installation related functions can-
not be used. 
						

							Setting Various Functions
140
Resetting to the Default Setting
[Factory defaults]
You can reset the menu item settings and 
restore the system settings to the factory 
defaults.
MENU > [System settings] > [Other settings] > 
[Factory defaults]
MENU > [System settings] > [Other settings] > 
[Factory defaults]
Select [Factory defaults] and press the OK 
button. The following screen for confirma-
tion appears.
 This function does not reset the values for 
[Lamp counter], [Language], [Remote con-
trol], [Input signal], [Network Setting], [Filter 
counter], [Focus position], [Zoom position], 
and [Lens shift position].
 For factory defaults settings, refer to pages 
232 – 238.
 The contents of the user memory return to the 
conditions at the time it was saved. (P110)
HDMIComponent
Digital PCAnalog PC
OKSettings are reset to default.
CancelSettings are not reset to default.