Canon projector REALiS SX6000 D Pprojector Ro AV User Manual

							121
Setting Various Functions
User’s ManualSettin
g Functions from Menus
Skip the POWER Button 
Operation
[Direct power on]
You can turn on the projector by connect-
ing the power cable without pressing the 
POWER button.
MENU > [System settings] > [Direct power on]
MENU > [System settings] > [Direct power on]
Press the OK button to accept your setting 
and then press the MENU button or EXIT 
button (WX6000 / SX6000).
 [Off] is the factory default.
HDMIComponent
Digital PCAnalog PC
OffYou need to press the POWER button 
to turn on the projector.
OnYou can turn on the projector by con-
necting the power cable only.
 Before setting the direct power on to 
[On], be sure to set the [Power man-
agement mode] to [Standby] or 
[Exit].

After turning off the projector, wait at 
least 5 minutes before turning it on 
again. It may shorten the lamp life if 
you turn on the projector immediately 
after turning it off. 
						

							Setting Various Functions
122
Enabling / Disabling the 
Beep
[Beep]
You can select whether a beep sounds or 
not when you operate the projector.
MENU > [System settings] > [Beep]
MENU > [System settings] > [Beep]
Press the OK button to accept your setting 
and then press the MENU button or EXIT 
button (WX6000 / SX6000).
 [On] is the factory default.
 The beep will not sound if you mute the 
projector sound with the MUTE button on 
the remote control.
Key Repeat
[Key repeat]
By pressing and holding the button on the 
projector or the remote control you can 
operate Key repeat in the same was as 
when the button is pressed repeatedly.
MENU > [System settings] > [Key repeat]
Press the OK button to accept your setting 
and then press the MENU button or EXIT 
button (WX6000 / SX6000).
 The factory default is [On].
 Even when Key repeat is [Off], Focus adjust-
ment, Zoom Adjustment and Lens shift 
adjustment can still be used.
HDMIComponent
Digital PCAnalog PC
OffDisables the beep.
OnEnables the beep.
HDMIComponent
Digital PCAnalog PC
OffKey repeat is not enabled.
OnKey repeat is enabled. 
						

							123
Setting Various Functions
User’s ManualSettin
g Functions from Menus
Prohibiting Operations
[Key lock]
You can lock the projector to prevent its 
operation from either the main unit or 
remote control.
MENU > [System settings] > [Key lock]
MENU > [System settings] > [Key lock]
Press the OK button to accept your setting 
and then press the MENU button or EXIT 
button (WX6000 / SX6000).
 [Off] is the factory default.
HDMIComponent
Digital PCAnalog PC
OffDisables the key lock.
Main 
unitOperation is not possible using the 
main unit.
Use the remote control.
Remote 
controlInfrared remote control operations 
can no longer be performed. Use the 
main unit button. If using the 
WX6000 / SX6000, this can also be 
set by connecting a cable. (P30)
The key lock function becomes effec-
tive from the moment the OK button is 
pressed after selecting [Main unit] or 
[Remote control]. Control via the item 
selected will then be disabled.
To Unlock Key Lock Function
Turn off the projector and unplug the 
power plug. Hold down the OK button 
on the main unit and connect the 
power plug. Keep holding down the 
OK button until a beep sounds. The 
key lock will be unlocked. 
						

							Setting Various Functions
124
Main Unit and Remote 
Control Channel Settings
[Remote control]
When using multiple projectors at the 
same time (maximum 4), you can assign a 
different channel to each remote control so 
that each operates independently.
For the WX6000 / SX6000, set this when 
performing infrared operations.
Select the main unit channel.
MENU > [System settings] > [Remote control]
MENU > [System settings] > [Remote control]
Press the OK button to accept your setting 
and then press the MENU button or EXIT 
button (WX6000 / SX6000).
 The factory default is [Independent] for 
both projector and remote control.
 After changing the channel on the menu, 
be sure to change the channel of the 
remote control too.
 If a cable is connected, it is not necessary 
to perform remote control channel setting.
Selecting a Channel on the Remote control
You can change the channel on the 
remote control as follows.
HDMIComponent
Digital PCAnalog PC
Ch1
Ch2
Ch3
Ch4Select the remote control 
channel to use with this 
projector.
IndependentRemote controls set to any 
channel can be used.
Ch1Press and hold the OK button 
and [ ] button at the same time 
for 3 seconds.
Ch2Press and hold the OK button 
and [ ] button at the same time 
for 3 seconds.
Ch3Press and hold the OK button 
and [ ] button at the same time 
for 3 seconds.
Ch4Press and hold the OK button 
and [ ] button at the same time 
for 3 seconds.
Inde-
pendentPress and hold the OK button 
and MENU button at the same 
time for 3 seconds.
Ch1Press and hold the Ch button 
and 1 button at the same time 
for 3 seconds.
Ch2Press and hold the Ch button 
and 2 button at the same time 
for 3 seconds.
Ch3Press and hold the Ch button 
and 3 button at the same time 
for 3 seconds.
Ch4Press and hold the Ch button 
and 4 button at the same time 
for 3 seconds.
Inde-
pendentIndependent  Press and hold the 
Ch button and 0 button at the 
same time for 3 seconds. 
						

							125
Setting Various Functions
User’s ManualSettin
g Functions from Menus
Selecting a Display Language
[Language]
You can select the language in which the 
menus are displayed.
MENU > [System settings] > [Language]
Use the [ ] / [ ] / [ ] / [ ] buttons to 
select the menu language, then press the 
OK button.
When the setting is completed, press the 
OK button to accept your setting and then 
press the MENU button or EXIT button 
(WX6000 / SX6000).
HDMIComponent
Digital PCAnalog PC
English
German
French
Italian
Spanish
Portuguese
Swedish
Russian
Dutch
Finnish
Norwegian
Turkish
Polish
Hungarian
Czech
Danish
Arabic
Chinese (Simplified)
Chinese (Traditional)
Korean
Japanese 
						

							Setting Various Functions
126
Showing / Hiding the 
Guide Screen
[Guide]
You can select whether to show or hide the 
guide screen which explains operations.
MENU > [System settings] > [Guide]
MENU > [Install settings] > [On screen] > 
[Guide]
Press the OK button to accept your setting 
and then press the MENU button or EXIT 
button (WX6000 / SX6000).
 [On] is the factory default.
 The guide screen is shown at the following 
times.
-Power is turned off by pressing the
POWER button. (P80)-No input signal can be detected. (P58)
-An invalid button is pressed in the
[BLANK], [FREEZE] or [D.ZOOM]
mode. (P82, P84)
-When the positional lock (P139) is set to
[On] (WX6000 / SX6000)
HDMIComponent
Digital PCAnalog PC
OffHides the guide screen.
OnShows the guide screen. 
						

							127
Setting Various Functions
User’s ManualSettin
g Functions from Menus
Showing / Hiding the 
Input Status
[Show Input Status]
You can select whether the signal status is 
displayed on the screen when there is no 
signal or when making signal settings.
MENU > [System settings] > [Show Input Sta-
tus]
MENU > [Install settings] > [On screen] > [Show 
input status]
Press the OK button to accept your setting 
and then press the MENU button or EXIT 
button (WX6000 / SX6000).
 [On] is the factory default.
Selecting the HDMI Input
[HDMI In]
Set the type of equipment which is con-
nected to the HDMI port.
MENU > [System settings] > [HDMI In]
MENU > [System settings] > [HDMI In]
Press the OK button to accept your setting 
and then press the MENU button or EXIT 
button (WX6000 / SX6000).
HDMIComponent
Digital PCAnalog PC
OffThe input status is not displayed.
OnThe input status is displayed.
HDMIComponent
Digital PCAnalog PC
AutoSelect when AV equipment will 
be connected. Image pro-
cessing, menu displays, and 
other elements are adjusted 
for video equipment.
ComputerSelect when a computer will be 
connected. Image processing, 
menu displays, and other ele-
ments are adjusted for a com-
puter. 
						

							Setting Various Functions
128
Setting a Password
[Password settings]
Disables the projector unless the correct 
password is entered.
MENU > [System settings] > [Other settings] > 
[Password settings]
MENU > [System settings] > [Other settings] > 
[Password settings]
Press the OK button to accept your setting 
and then press the MENU button or EXIT 
button (WX6000 / SX6000).
 [Off] is the factory default.
 You cannot set [On] unless you have com-
pleted [Register password].
Once you set a password, the password 
entry screen appears at power-on.
Enter a 4 digit password.
For the WUX5000 / WUX4000, the pass-
word can be entered using the [ ] / [ ] / 
[ ] / [ ] buttons. For the WX6000 / SX6000, the password can be entered 
using a combination of the numerical but-
tons and the [ ] / [ ] / [ ] / [ ] buttons. 
[ ] / [1], [ ] / [2], [ ] / [3], and [ ] / [4] 
have the same function.
If the password is valid, the projection 
starts. If you enter a wrong password three 
times, the power will be turned off.
 The power is also turned off if no password 
is input for 3 minutes.
HDMIComponent
Digital PCAnalog PC
Off
The projector can be used even if no pass-
word is entered.
OnThe projector cannot be used unless you 
enter your password.
T o Cancel the P asswordTurn off the projector and unplug the power 
plug. 
Hold down the 
MENU button on the side control 
and connect the power plug. Make sure to keep 
holding down the 
MENU button until a beep 
sounds. When the beep sounds, the password 
is canceled. (The entered password is also 
reset.)
To forcibly cancel the password from the remote 
control, in standby state press the 
MENU button 
3 times, then press the POWER button. 
						

							129
Setting Various Functions
User’s ManualSettin
g Functions from Menus
Registering a Password
[Register password]
You can register a password for starting 
projection.
MENU > [System settings] > [Other settings] > 
[Register password]
MENU > [System settings] > [Other settings] > 
[Register password]
Press the OK button after selecting [Reg-
ister password], and the following screen 
for registering a password appears.Enter a 4 digit password.
For the WUX5000 / WUX4000, the pass-
word can be entered using the [ ] / [ ] / 
[ ] / [ ] buttons. For the WX6000 / 
SX6000, the password can be entered 
using a combination of the numerical but-
tons and the [ ] / [ ] / [ ] / [ ] buttons. 
[ ] / [1], [ ] / [2], [ ] / [3], and [ ] / [4] 
have the same function.
The 4-digit password is entered from the 
left to right digits. When the final digit is 
entered, the password is automatically 
registered.
 Press the MENU button to abort the regis-
tration.
HDMIComponent
Digital PCAnalog PC 
						

							Setting Various Functions
130
Prohibiting Operation of 
the Lens
[Lens Ctrl Lock]
You can lock lens-related button opera-
tions.
MENU > [System settings] > [Other settings] > 
[Lens Ctrl Lock]
Press the OK button to accept your setting 
and then press the  MENU button.
• [Off] is the factory default.
HDMIComponent
Digital PCAnalog PC
Off Focus, zoom, lens shift, and other 
lens-related operations are permit-
ted.
On Focus, zoom, lens shift, and other 
lens-related operations are locked.