Canon printer PIXMA SELPHY ES2 User Manual

							
Introduction to the Supplied Programs
71Printing from a PC
4Select   [Text], click [Add/Edit].
5Type the desired text to print, click  , adjust the position of 
the text, then click   [Print].
6Determine the printer name, paper size, cartridge, layout, and 
copies, then click  .
7Printing completes.
2• Frames can be assigned only when [Postcard size] or [L size] paper is selected.
6• The image will not print correctly if you change the paper size setting.  
						

							
72Using the Battery Pack (SELPHY ES2 only)
Using the Battery Pack 
(SELPHY ES2 only)
You can print outdoors or at locations without a 
power outlet by installing Battery Pack NB-ES1L 
(sold separately) into the SELPHY ES2. SELPHY 
ES20, however, does not accept a battery pack.
Use of genuine Canon accessories is recommended.
This product is designed to achieve excellent performance when 
used with genuine Canon accessories. Canon shall not be liable 
for any damage to this product and/or accidents such as fire, 
caused by the malfunction of non-genuine Canon accessories 
(e.g., a leakage and/or explosion of a battery pack). Please note 
that this warranty does not apply to repairs arising out of the 
malfunction of non-genuine Canon accessories, although you may 
request such repairs on a chargeable basis.
• Battery Pack NB-CP2L cannot be used.
• Do not use the battery pack in products other than those recommended by Canon.
• Do not lose the battery pack terminal cover. It is required for battery storage.  
						

							
73Using the Battery Pack (SELPHY ES2 only)
Installing the Battery Pack
Install the battery pack NB-ES1L (sold separately) to the printer.
1Remove the battery packs terminal 
cover.
2Remove the battery cover lever.
3Install the battery pack in the printer.
1• If the battery terminals are dirty, it results in a poor connection. 
Before recharging or using the 
battery, polish the terminals with 
a slender, soft tipped cotton 
swab.
• When the battery pack is not  used, remove it from the printer 
and be sure to put the terminal 
cover on.
2• To remove the battery cover, slide the battery cover lever 
upwards and remove the cover.
3• Push the battery pack until it clicks into place.
• To remove the battery pack,  slide the battery cover lever 
upwards and remove the 
battery.  
						

							
74Using the Battery Pack (SELPHY ES2 only)
Charging the Battery Pack
Install the battery pack NB-ES1L and charge it.
• It takes approximately 4 hours to bring a depleted battery pack to a full charge state (based on standard Canon testing criteria).
- We recommend recharging the battery pack in a temperature of 5 - 40 °C (41 - 104 °F).
- The charging time will vary depending on the ambient temperature and charge state.
• If Auto Power Down is set to [On], the printer will automatically turn off when powered by the  battery if it is not used for five minutes or more.
1Install the battery pack in the printer.
• For details on how to install, refer to Installing  the Battery Pack (p. 73).
2Connect the compact power adapter to 
the printer.
• For more connection details, refer to Placing/
Connecting the Printer (p. 22).
• Charging starts.
3Disconnect the compact power adapter 
cord from the printer once charging is 
complete.
Situate the printer with at least 
15 cm (6 in.) of free space in 
front and back and at least 10 
cm (4 in.) of free space on the 
sides.
To power outlet 15 cm 
(6 in.)
10 cm 
(4 in.)15 cm 
(6 in.)
2• The power lamp lights orange 
while charging and turns off 
once the battery pack is fully 
charged.
• If the printers power turns on  while charging the battery pack, 
charging will stop. If the power 
is turned off again, charging will 
resume.
• Turn the printer power off and  turn it on again if the battery 
does not start charging.  
						

							
75Using the Battery Pack (SELPHY ES2 only)
Checking the Battery Status
If battery power is low, the printers power lamp blinks orange. Check battery status by the icon or 
message displayed in the LCD monitor of the printe r, and recharge the battery pack or change it 
for a fully charged one.
Battery Status
IndicationDescription
There is sufficient battery power.
To use the printer for a long time, ei ther use fully charged batteries or 
charge the battery as soon as possible.
Battery power is low. We recommend recharging the battery pack.
 (Blinking red) Printing is not possible.
Recharge the printer 
battery Change it for a fully charged battery pack or recharge the battery 
pack immediately. You can also use the printers compact power 
adapter.  
						

							
76Using the Battery Pack (SELPHY ES2 only)
Handling of the Battery Pack
Battery Storage
zRemove the battery pack from the printer when the battery pack is not used, be sure to attach 
the terminal cover.
z Do not carry or store the battery pack with meta l objects with sharp edges, such as paper clips 
and pins. Always put the terminal cover on the batte ry packs terminal when carrying it or before 
storing it.
z When storing a battery pack, you are recommended to  use it in the printer until it is completely 
discharged and to store it in an indoor location with low relative humidity and between the 
temperatures of 0 - 30 °C (32 - 86 °F). Storing t he battery fully charged for long periods of time 
(about 1 year) shortens the battery life and caus es its performance to decline. When you do not 
use it for long period of time, fully charge it once  a year and store after fully discharging it in the 
printer.
• This is a lithium ion battery pack so there is no need to completely use or discharge it before 
recharging.
- It can be charged at any time.
• You are advised to charge the battery on the day of use, or one day before, to ensure a full  charge.
- Even charged battery packs continue to discharge naturally.
• If the performance of the battery diminishes substantially even when it is fully charged, its life has  been exceeded and it should be replaced.
• If battery power is low, the finished print may no t be ejected into the print receptacle completely 
and printing may stop. 
- If this happens, change the battery pack with a fully charged one, or use the printers compact  power adapter.
• Although the battery packs maximum operating range is 5 to 40 °C (41 to 104 °F), the optimal  range is 10 to 30 °C (50 to 86 °F).
• At lower temperatures, battery performance is sometimes reduced and the low battery power  icon ( ,  ) may be displayed earlier than usual.
- Battery performance can be recovered by putting the battery pack in your pocket, for example,  to warm it up before use.  
						

							
77Appendix
Appendix  
						

							
78Appendix
Making Printer Settings
You can make various printer settings, such as language or power saving settings.
How to Use the Menu
1Turn the printer on and press  .
2Press   or   to select [Printer Setup] and press  .
3Press   or   to select the item and change the setting value.
4Press .
• The setting value is saved.• The printer setup screen is displayed.
• For the settings of each item, refer to pp. 79 - 81.
3• [Bluetooth] is displayed only when a Bluetooth unit is connected.
4• If you press  , the setting is canceled and the screen returns to the menu screen.  
						

							
Making Printer Settings
79Appendix
Printer Setup Menu
The default setting is marked as  .
Bluetooth Settings
ItemDescriptionSettings
Auto Rotate By setting the camera, the image can be automatically 
rotated on the LCD monitor. On , Off
Auto Power 
Down The printer automatically tu
rns off if no operation is 
performed for five minutes. On , Off 
Bluetooth Sets the model name and/or security details when using 
Bluetooth. [Bluetooth] is displayed only when a Bluetooth 
unit (sold separately) is connected. Refer to p. 79
Language Sets the display language of the LCD monitor. Refer to p. 81
Transition Sets the transition effects when you switch the image. Fade, Wipe, 
Off 
Reset All Reset the printers settings to their defaults. –
Device name Selects a name from Canon ES2-1 ( ) to ES2-9 (ES20-1 to ES20-9). 
This is the name used when the target  device (this printer) is selected 
from the mobile phone. This setting distinguishes this device when 
there are two or more Bluetooth-enabled devices capable of 
communication.
Security Selects either [On] or [Off] ( ). When set to [On], the passkey for the 
printer and mobile phone must be entered when connecting to the 
printer.
Passkey The passkey refers to an identification number to be determined. It is 
used to prevent incorrect access from other Bluetooth devices. When 
[Security] is set to [On], press   and set the key (4-digit 
number) to enter on the mobile phone to enable printing. The default 
passkey is 0000.
Deny Access Selects either [On] or [Off] ( ). Selecting [On] will disable searching 
and printing from Bluetooth devices.
Reset Reset Bluetooth settings to their defaults.  
						

							
Making Printer Settings
80Appendix
1Press   to select [Printer Setup].
2Select [Bluetooth] and press  .
• The Bluetooth setting screen is displayed.
3Press   or   to select the items you wish to set and change 
setting values.
4Press .
• The setting is saved and the screen returns to [Printer Setup].
1• For how to use the menu, refer to page 78.
• For how to print using a Bluetooth unit, refer to Printing via Bluetooth (p. 57).