Canon printer PIXMA MG6620 User Manual

Note•
The effects of the quiet mode may be less depending on the print quality settings.231 

Changing the Printer Operation ModeIf necessary, switch between various modes of printer operation.
The procedure for configuring  Custom Settings is as follows:
 Custom Settings
1.
Open the printer driver setup window
2.
Make sure that the printer is on, and then click  Custom Settings on the Maintenance
tab
The  Custom Settings  dialog box opens.
Note
•
If the printer is off or if communication between the printer and the computer is disabled, an
error message may appear because the computer cannot...

Don't detect mismatch of paper settings when printing from computerWhen you print documents from your computer and the paper settings on the printer driver and
the printer do not match, this setting disables the message display and allows you to continue
printing.
To disable detection of paper setting mismatches, select this check box.
Ink Drying Wait Time You can set the length of the printer rest time until printing of the next page begins. Moving the
slider to the right increases the pause time,...

Changing the Machine Settings on the LCD
Changing the Machine Settings Using the Operation Panel
Print settings
LAN settings
Device user settings
PictBridge print settings
Language selection
Home screen background color
Firmware update
Cassette settings
Reset setting
About ECO settings
About Quiet setting
Using the Machine with the Access Point Mode
234 

Changing the Machine Settings Using the Operation PanelThis section describes the procedure to change the settings in the  Device settings screen, taking the steps
to specify  Extended copy amount  as an example.1.
Make sure that the machine is turned on.
2.
Flick the HOME screen, then tap  Setup .
Using the Operation Panel
3.
Tap  Device settings .
The  Device settings  screen is displayed.
4.
Tap the setting item to adjust.
The setting screen for the selected item is displayed.
5.
Tap the setting...

You can select the setting menus below.
Print settings
LAN settings
Device user settings
PictBridge print settings
Language selection
Home screen background color
Firmware update
Cassette settings
Reset setting
Note
•
You can use the machine considering the environment, such as setting 2-sided printing as default orenabling the machine to turn on/off automatically.
About ECO settings
•
You can reduce the operating noise when printing at night.
About Quiet setting
236 

Print settings•
Prevent paper abrasion
Use this setting only if the print surface becomes smudged.
Important
•
Be sure to set this back to  OFF after printing since it may result in lower printing speed or lower
print quality.
•
Extended copy amount
Selects the amount of image that extends off the paper when printing in borderless (full). Slight cropping may occur at the edges since the copied image is enlarged to fill the whole page. You
can change the width to be cropped from the borders of the...

Important•
For Letter-sized or Legal-sized paper, you can adjust the left/right margins between -0.05inches/-1.5 mm and +0.05 inches/+1.5 mm even if you specify the value over 0.05 inches/1.5 mm.238 

LAN settings•
Change LAN
Enables either wireless LAN or access point mode. You can also disable wireless LAN or access point
mode.
•
Wireless LAN setup
Selects the setup method for wireless LAN connection.
Note
•
You can also enter this setting menu by selecting  WLAN on the HOME screen. In this case, enable
wireless LAN.
When this menu is selected, the machine starts searching for a WPS-compatible access point. If the
machine detects the access point, follow the on-screen instructions to set up wireless...

Communication modeInfrastructureChannelXXWireless LAN securityInactive/WEP(64bit)/WEP(128bit)/WPA-PSK(TKIP)/WPA-PSK(AES)/WPA2-PSK(TKIP)/WPA2-PSK(AES)IPv4 addressXXX. XXX. XXX. XXXIPv4 subnet maskXXX. XXX. XXX. XXXIPv4 default gatewayXXX. XXX. XXX. XXXIPv6 addressXXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXXIPv6 subnet prefix lengthXXXIPv6 default gatewayXXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXXMAC addressXX:XX:XX:XX:XX:XXIPsec settingsEnable (ESP)/Enable (ESP & AH)/Enable (AH)/DisablePre-shared...