Canon printer PIXMA i560 Series User Manual

Printing Maintenance29
Printing Maintenance
Replacing an Ink Tank
When replacing an ink tank, check the model number very carefully. 
The printer will not print properly if the wrong ink tank is used, or installed in 
the incorrect position.
With this printer, ink tanks must be installed in the order of yellow, magenta, 
cyan and black.• Yellow: BCI-6Y • Cyan: BCI-6C
• Magenta: BCI-6M • Black: BCI-3eBK
„Knowing When to Replace an Ink Tank
If an ink tank needs to be replaced, once printing begins, the...

Printing Maintenance
30
The following message appears when ink is empty. Printing will resume as soon as an ink 
tank is replaced and the front cover is closed.
NoteWhen Low Ink is Detected
TheBJ Status Monitor appears as soon as a print job starts.
[!] indicates a low ink level. Obta
in a replacement tank as soon 
as possible.
Note When Low Ink is Detected
The following message is displayed as soon as a print job 
starts.
[!] indicates a low ink level. Obta
in a replacement tank as soon 
as possible....

Printing Maintenance
31
„Replacing an Ink Tank
When an ink tank runs out of ink, replace it using the following steps.
1Ensure that the printer is on, and then open the front cover.
The print head holder moves to the center.
2Remove the empty ink tank.
(1)Push the tab and remove the ink tank.
3Prepare a replacement ink tank.
(1)Unpack the new ink tank and pull off the orange tape.
(2)Remove the orange protective cap from the bottom of the ink tank and discard it. ImportantzHandle ink tanks carefully to...

Printing Maintenance
32
4Install the ink tank.
(1)Insert the ink tank in the print head holder.
(2)Press on the PUSH mark until the ink tank snaps firmly into place.
5Close the front cover.
The print head holder moves to the right. The ink tank installation process is now 
complete. ImportantzDo not squeeze the side of ink tanks as this may cause the ink to 
leak out and stain your clothes and hands.
zDo not re-attach the protective cap once you have removed it.
zOnce the protective cap is removed, do...

Printing Maintenance33
When Printing Becomes Faint or Colors are Incorrect
When printing becomes faint or colors are incorrect, even if ink remains in the 
ink tanks, the print head nozzles are probably clogged. Follow the 
procedures below to maintain the print head.Important Before maintaining the print head, check the following:
zOpen the front cover and make sure the ink tank contains 
ink. If it is out of ink, replace it.
z Ensure that all the orange tape of the ink tank has been 
peeled off.
z...

Printing Maintenance
34
Printing the Nozzle Check Pattern
Print the nozzle check pattern to determine whether the ink ejects properly from the print 
head nozzles, and to verify print head alignment. Use this function when printed results are 
blurred or the color is incorrect.
1With the printer on, load a sheet  of Letter paper in the printer.
2Open the Printer Properties dialog box.
See Opening the Printer Properties Dialog  Box Directly from the Start Menu on 
page 15.
3Print the Nozzle Check...

Printing Maintenance35
1With the printer on, load a sheet  of Letter paper in the printer.
2Open the Printer Utility dialog box.
(1)Select  Page Setup...  in the File menu.
(2) Click  Utilities  to open the  Printer Utility  dialog box.
3Print the Nozzle Check Pattern.
(3)When the confirmation message is displayed, click  OK.
See  Examining the Nozzle Check Pattern  on page 36.
(1)Select  Te s t  P r i n t  from the 
pull-down menu. 
(2)Click  Nozzle Check .
i560_QSG_US.book  Page 35  Tuesday, May 6,...

Printing Maintenance
36
„Examining the Nozzle Check Pattern
The nozzle check pattern should appear as follows when ink is discharged properly.
Examine the nozzle check pattern output by the printer.
(1) If lines are missing as in the illustration, run the print head cleaning procedure 
for Black 3eBK .
See  Print Head Cleaning  on page 38.
(2) White stripes in this pattern require ru nning print head cleaning procedure for 
Color 6C, 6M, 6Y .
See  Print Head Cleaning  on page 38.
(3) Unevenness in this...

Printing Maintenance37
(4)White vertical stripes in this pattern indicates the print head requires alignment.
See  Aligning the Print Head  on page 42.
(5) Horizontal stripes in this patterns indi cate the print head requires alignment.
See  Aligning the Print Head  on page 42.
When vertical stripes appear
When horizontal stripes appear
i560_QSG_US.book  Page 37  Tuesday, May 6, 2003  1:43 PM 

Printing Maintenance
38
Print Head Cleaning
Clean the print head if you suspect that the nozzles might be clogged. Cleaning  the print  
head consumes ink, so perform print head cleaning only when necessary.
1Ensure that the printer is on.
2Open the Printer Properties dialog box.
See Opening the Printer Properties Dialog  Box Directly from the Start Menu on 
page 15.
3 Start Print Head Cleaning.
(3) Select the ink nozzles to be cleaned, and then click  Execute.
All colors :All nozzels
Black 3eBK : Black...