Canon printer MAXIFY MB2320 User Manual

Ink Remaining Level Is Not Displayed on Printer Status Monitor of
the Machine
Use the printer driver with bidirectional communication. Select  Enable bidirectional support  in the Ports sheet of the properties dialog box of the printer driver.
How to Open the Printer Driver Setup Window
911 

Printing Speed Is Slow
Check1 The machine may be printing out a large job issued from another computer.
Check2 When using wireless LAN, make sure that the radio status is good and adjust
the installation positions while monitoring the radio status with IJ Network Tool.
Monitoring Wireless Network Status
Make sure that there is no barrier or obstacle between the access point and the machine. Wireless communication between different rooms or floors is generally poor. The metal, concrete, or timber...

Cannot Use the Machine on Replacing an Access Point or
Changing Its settings
When you replace an access point, perform network setup of the machine again. Perform network setup again with the Setup CD-ROM or perform it again according to the instructions on
our website.
If the problem is not resolved, see below.
Cannot Communicate with the Machine After Applying MAC/IP Address Filtering or Entering an
Encryption Key to the Access Point
When Encryption Is Enabled, Cannot Communicate With the Machine After...

When Encryption Is Enabled, Cannot Communicate With the Machine
After the Encryption Type Was Switched on the Access Point
If the machine cannot communicate with the computer after the encryption type of the machine was
switched, make sure that encryption types for the computer and the access point matches that set to the machine.
Cannot Communicate with the Machine After Applying MAC/IP Address Filtering or Entering an
Encryption Key to the Access Point
914 

Cannot Detect a Machine on a Network
Cannot Detect the Machine When Setting up Network Communication
The Machine Cannot Be Detected in the Wireless LAN
The Machine Cannot Be Detected in the Wired LAN
Note
•
You cannot use the wireless LAN and the wired LAN at the same time.
915 

Cannot Detect the Machine When Setting up Network
Communication
If the machine could not be detected on the network when setting up the network communication, confirmthe network settings before redetecting the machine.
Cannot Detect the Machine during Wireless LAN Setup: Check 1
Cannot Detect the Machine during Wired LAN Setup: Check 1
Note
•
You can set up the network communication via USB. To set up via USB, select the  Set up the network
connection via USB  check box on the Check Printer Settings...

Cannot Detect the Machine during Wireless LAN Setup: Check 1
Are the machine and network device (router, access point, etc.) turned on?Make sure that the machine is turned on.
Confirming that the Power Is On
Make sure that the network device (router, access point, etc.) is turned on.
If the machine or the network device is turned off: Turn on the machine or the network device.
After turning on the machine or the network device, it may take some time until ready for use. After a while
just turning on the...

Cannot Detect the Machine during Wireless LAN Setup: Check 2
Is the wireless LAN setting of the machine enabled?Make sure that the 
 or  icon below is displayed on the touch screen.
If the icon is not displayed: The wireless LAN setting of the machine is disabled. Enable the wireless LAN setting of the machine.After enabling the wireless LAN setting, click  Back to Top on the Check Printer Settings  screen to try to
set up the network communication from the beginning.
If the icon is displayed:
Go to...

Cannot Detect the Machine during Wireless LAN Setup: Check 3
Is the machine connected to the access point?
By using the icon on the touch screen, make sure that the machine is connected to the access point.
If the  icon is displayed:
The machine may be placed far away from the access point. Place the machine near the access point temporarily, then click  Redetect on the Check Printer Settings  screen.
When the machine is detected, follow the instructions on the screen to continue to set up the network...

Cannot Detect the Machine during Wireless LAN Setup: Check 4
Are the SSID of the access point connected to your computer and thatconnected to the machine the same?
You can confirm the SSID of the access point connected to the machine on the touch screen.
Select  Setup on the HOME screen, then select  Device settings > LAN settings  > Confirm LAN
settings  > WLAN setting list .
From your computer, you can confirm the SSID of the access point connected to your computer. In
Windows 8.1, Windows 8, Windows...