Canon printer MAXIFY MB2320 User Manual

Service nameSpecifies the Bonjour service name. You can use up to 48 characters for the name.
Note
•
You cannot use the same service name as that already used for other LAN connected devices.
◦
LPR protocol setting
Activates/deactivates the LPR setting.
◦
Wireless LAN DRX setting
Selecting  Enable allows you to activate discontinuous reception when using wireless LAN. It allows
you to save electricity.
Note
•
Depending on the access point you are using, discontinuous reception may not be activated even...

Device user settings
Important
•
This setting item is for the administrator.
•
Date/time setting
Sets the current date and time.
Setting the Sender Information
•
Date display format
Sets the format of dates displayed on the touch screen and printed on sent faxes and photos.
Note
•
When  ON is selected for  Print date on the print settings screen in printing from a USB flash drive,
the shooting date is printed in the date display format you selected.
Setting Items for Photo Printing Using the Operation...

Selects the alarm volume.◦
Line monitor volume
Selects the line monitor volume.
◦
Offhook alarm
Selects the alarm volume when the phone receiver is not put on the hook properly.
•
Country or region
Selects the country or region where you are using the machine.
Note
•
This setting may not be available depending on the country or region of purchase.
•
Device info sending setting
Selects whether you will send the printer usage information to Canon server. The information sent to
Canon will be utilized to...

Language selection
Important
•
This setting item is for the administrator.
Changes the language for the messages and menus on the touch screen.
264 

Firmware update
Important
•
This setting item is for the administrator.
You can update the firmware of the machine, check the firmware version, or perform settings of a
notification screen, a DNS server and a proxy server.
Note
•
Only  Check current version  is available when Disable LAN is selected for  Change LAN in LAN
settings .
•
Install update
Performs the firmware update of the machine. If you select  Yes, the firmware update starts. Follow the
on-screen instructions to perform update.
Important...

Cassette settingsBy registering the paper size and the media type loaded in the cassette, you can prevent the machine from
misprinting by displaying the message before printing starts when the paper size or the media type of the
loaded paper differs from the print settings. In addition, you can allow the machine to switch the paper
source automatically when a cassette runs out of paper.
For details:
Paper Setting for Printing
•
Register cassette paper info
Registers the paper size and the media type you...

Administrator password setting
Important
•
This setting item is for the administrator.
You can specify or disable the administrator password.
Specifying the administrator password requires you to enter the password to change the machine settings or connection settings.
Entering the administrator password is required to change the setting items in the following menus.
•
ECO settings
•
Quiet setting
•
Web service setup
•
FAX settings
•
LAN settings
•
Device user settings
•
Language selection
•
Firmware...

Operation restrictions
Important
•
This setting item is for the administrator.
You can restrict printing, copying, or faxing operations or to use a USB flash drive or a shared folder on the
computer.
Note
•
When no operation restrictions are enabled, the confirmation screen to enable operation restrictions is displayed. Tapping  Yes enables you to restrict operations. If you have already restricted any
operations, the menu items are displayed. Tapping  Change operation restrictions enables you to
change...

Reset setting
Important
•
This setting item is for the administrator.
Reverts all settings you made to the machine back to the default. However, some data may not be changed, depending on the current usage state of your machine.
Important
•
Depending on the setting item, it is necessary to perform connection or setup again after you have
reverted the setting back to the default.
•
Web service setup only
Reverts the Web service settings back to the default.
•
LAN settings only
Reverts the LAN settings...

1.Display the User information settings  screen.
Setting the Sender Information
2.
Tap the user's name or the telephone number, then delete all characters or numbers.
3.
Tap OK when you finished deleting all characters or numbers.
270