Canon Pixma Mx532 User Guide

Bluetooth settings Screen1.
Device name
Displays the device name of the printer to which the Bluetooth unit is attached.
2.
Access refusal
Selecting  ON will disable searching of this printer by a Bluetooth-compatible device.
3.
Security settings
Select  Enable  and then specify the security mode to activate the passkey set on the  Passkey screen.
4.
Passkey
You can change the passkey. The passkey refers to an identification number to be determined. It is used
to prevent unwanted access from other...

Security settings Screen•
Enable
Selecting  Enable allows you to choose either of the security modes below.
◦
Mode 3 (recommend)
This mode is activated on link level enforced security.
The passkey will be required when a Bluetooth device communicates with the printer. Normally
select this mode.
◦
Mode 2
This mode is activated on service level enforced security.
The passkey will be required when printing through the Bluetooth communication.
After setting the security mode, we recommend making a trial...

SpecificationsCommunication
methodBluetooth v2.0Maximum Speed1.44 MbpsOutputBluetooth Power Class 2Communication
distanceLine-of-sight distance: approx. 33 ft./10 m *
* It may vary depending on factors including the presence of obstacles betweencommunication equipment, radio wave conditions, the presence of magnetic fields around
microwave ovens and locations where electrostatic and radio interference occur, the types of
software and operating systems used, and receiver sensitivity and antenna...

Dimensions (Width x
Depth x Height)18.5 (W) x 47.5 (D) x 8.7 (H) mm (with cap attached)
0.73 (W) x 1.87 (D) x 0.35 (H) inchesWeightApprox. 7 g (0.25 oz)
184
 

Copying
Making Copies Basic
Setting Items for Copying
Reducing or Enlarging a Copy
Two-Sided Copying
About Special copy Menu
Copying Two Pages to Fit onto a Single Page
Copying Four Pages to Fit onto a Single Page
Copying Thick Originals Such as Books
Copying without Borders
Collated Copying
185
 

Making CopiesThis section describes the basic procedure to perform standard copying.1.
Make sure that the machine is turned on.
2.
Load paper.
3.
Press the  COPY button.
The Copy standby screen is displayed.
Note
•
When  ON is selected for  Copy on ECO (2-sided) , the Two-sided copy standby screen is
displayed as shown below. You can copy two original pages or a two sided page onto the both
sides of a single sheet of paper.
Follow the procedure below to deactivate two-sided copying temporarily.
1.
Press...

7.Press the Color button for color copying, or the  Black button for black & white copying.
The machine starts copying.
Remove the original on the platen glass or from the document output slot after copying is complete.
Important
•
If you load the original on the platen glass, do not open the document cover or remove the original while  Scanning...  is displayed on the screen.
•
If you load the original in the ADF, do not move the original until copying is complete.
Note
•
To cancel copying, press the...

Setting Items for CopyingYou can change the copy settings such as the page size, media type, and intensity.Press the  Menu button, use the 
 button to select a setting item, then press the  OK button.
Use the 
 button to adjust each setting item, then press the  OK button. The next setting item is
displayed.
The LCD returns to the Copy standby screen when all the settings are complete.
Note
•
The * (asterisk) on the LCD indicates the current setting.
•
Some settings cannot be specified in combination...

•Media type
Select the media type of the loaded paper.
Ex:•
Image quality
Select the image quality according to the original.
Ex:
Note
•
If you use  Draft with the media type set to  Plain paper and the quality is not as good as expected,
select  Standard  or High  and try copying again.
•
Select  High to copy in grayscale. Grayscale renders tones in a range of grays instead of black or
white.
•
4-on-1 layout
Select the layout when copying four original pages onto a single sheet of paper by reducing each...

Note
•
This setting item is displayed under the following conditions.
•
When 2-sided copy  is selected for  Special copy
Two-Sided Copying
•
When ON is selected for  Copy on ECO (2-sided)
About ECO settings
•
Stapling side
Select the stapling side.
Ex:
Note
•
This setting item is displayed under the following conditions.
•
When  2-sided copy  is selected for  Special copy
Two-Sided Copying
•
When ON is selected for  Copy on ECO (2-sided)
About ECO settings
190