Canon Pixma Ip110 User Guide

Connecting the Printer to the Computer Using a USB CableConnect the printer and the computer using a USB cable as the illustration below. The USB port is located
on the side of the printer.181
 

When Detecting the Printers Have the Same Name during SetupWhen the printer is detected during setup, you may see multiple printers of the same name on the detection
result screen.
Select a printer with checking the MAC address or the serial number set to the printer against that on the detection result screen.
Note
•
A serial number may not be displayed on the detection result screen.
To check the MAC address of the printer, print out the network setting information.
Printing Out Network Setting...

Connecting to Other Computer with LAN/Changing the Connection
Method from USB to LAN
To add the computer connecting the printer with LAN or to change the connection method between the
printer and the computer from USB to LAN, perform setup with the Setup CD-ROM or perform it according
to the instructions on our website.
Connecting to Other Computer with LANTo add the computer connecting the printer with LAN, perform setup with the Setup CD-ROM or perform it
according to the instructions on our website....

Printing Out Network Setting InformationYou can print out the current network settings of the printer.
Important
•
This print out contains valuable information about your computer. Handle it with care.
1.
Make sure that the printer is turned on.
2.
Load a sheet of A4 or Letter-sized plain paper.
3.
Press and hold the  RESUME/CANCEL  button, then release the button when the  POWER
lamp flashes 6 times.
The printer starts printing the network setting information.
The following information on the...

Subnet Prefix Length *2Subnet Prefix LengthXXXIPsec *3IPsec settingActiveSecurity Protocol *3Method of the Security ProtocolESP/ESP & AH/AHWPS PIN CODEWPS PIN codeXXXXXXXXWireless LAN DRXDiscontinuous reception
(wireless LAN)Enable/DisableOther SettingsOther settings-Printer NamePrinter namePrinter name (Up to 15 alphanumeric characters)WSDWSD settingEnable/DisableWSD TimeoutTimeout1/5/10/15/20 [min]LPR ProtocolLPR protocol settingEnable/DisableBonjourBonjour settingEnable/DisableBonjour Service...

About Network Communication
Changing and Confirming Network Settings
Screens for Network Connection of IJ Network Tool
Other Screens of IJ Network Tool
Appendix for Network Communication
186
 

Changing and Confirming Network Settings
IJ Network Tool
Changing the Settings in the Wireless LAN Sheet
Changing the WEP Detailed Settings
Changing the WPA/WPA2 Detailed Settings
Changing the Settings in the Wired LAN Sheet
Changing the Settings in the Admin Password Sheet
Monitoring Wireless Network Status
Initializing the Network Settings of the Machine
Viewing the Modified Settings
187
 

IJ Network ToolIJ Network Tool is a utility that enables you to display and modify the machine network settings. It is installed
when the machine is set up.
Important
•
To use the machine over LAN, make sure you have the equipment necessary for the connection type, such as an access point or a LAN cable.
•
Do not start up IJ Network Tool while printing.
•
Do not print when IJ Network Tool is running.
•
If the firewall function of your security software is turned on, a message may appear warning thatCanon...

Changing the Settings in the Wireless LAN SheetTo change the wireless network settings of the printer, connect the printer and the computer with a USB
cable temporarily. If you modify the wireless network settings of the computer over wireless connection
without USB connection, your computer may not be able to communicate with the machine after modifying
the settings.
Note
•
This screen is not available depending on the printer you are using.
•
Activate the wireless LAN setting of the printer to change...

Note•
Enter the same SSID that the access point is configured to use. The SSID is case-sensitive.
Encryption Method: Select the encryption method used over the wireless LAN.
You can change WEP settings with selecting  Use WEP and clicking  Configuration... .
Changing the WEP Detailed Settings
You can change WPA/WPA2 settings with selecting  Use WPA/WPA2 and clicking Configuration... .
Changing the WPA/WPA2 Detailed Settings
Important
•
If all encryption types of the access point, printer, or computer do...