Canon Pc170 User Guide

							Getting Started
9
1
●Clean the copier using a firmly wrung-out
cloth dampened with a mild cleansing
detergent. Do not use alcohol, benzene,
paint thinner or other flammable
substances. If flammable substances
come into contact with a high-voltage area
inside the copier, this may result in a fire
or electrical shock.
●Do not throw used cartridges into open
flames, as this may ignite the toner
remaining inside the cartridges and result
in burns or a fire.
CAUTION
●There are some areas inside the copier
which are subject to high voltages and high
temperatures. Take adequate precaution
when performing internal inspections, to
avoid burns or electrical shock.●When removing jammed paper or when
inspecting the inside of the copier, do not
allow necklaces, bracelets or other metal
objects to touch the inside of the copier, as
this may result in burns or electrical shock.
●When removing copy paper which has
become jammed from inside the copier, take
care not to allow the toner on the jammed
copy paper to come into contact with your
hands or clothing, as this will dirty your
hands or clothing. If they become dirty, wash
them immediately with cold water. Washing
with warm water will set the toner and make
it impossible to remove the toner stains.
●When removing copy paper which has
become jammed from inside the copier,
remove the jammed copy paper gently to
prevent the toner on the paper from
scattering and entering your eyes or mouth.
If toner enters your eyes or mouth, wash
immediately with cold water and consult a
physician.
●When loading copy paper or removing
jammed originals or copy paper, take care
not to cut your hands on the edges of the
original or copy paper.
Consumables
WARNING
●Do not throw cartridges into open flames,
as this may cause the toner to ignite and
result in burns or a fire.
●Do not store cartridges or copy paper in
places exposed to open flames, as this
may cause the cartridges or copy paper to
ignite and result in burns or a fire.
CAUTION
●Keep cartridges and other consumables
out of the reach of small children. If these
items are ingested, consult a physician
immediately.
Safety Considerations
01_PC170-USA06.5.15, 18:26 9
 
						

							Getting Started
10
1
Handling Precautions
Platen
•Do not stack objects onto, or press down
forcefully upon, the platen.
•The maximum allowable load that can be
placed on the cover is 4.4 lb.
Main Unit
•Do not let paper clips, staples, or other
foreign objects fall into the copier.
Also be careful not to spill any liquids or
flammable substances (such as paint
thinner, benzene or rubbing alcohol) on
the copier. If a foreign object or liquid
comes into contact with a dangerous
voltage point inside the copier
malfunction, fire or electrical shock could
occur.
•Do not lubricate any part of the copier.
•Do not use any extremely flammable
substances, such as aerosols, etc., near
the copier as such a substance may
ignite.
Handling Handling
Precautions Precautions
When not Using the Copier
•If you have to open the main unit to
replace the cartridge or remove jammed
paper, close the top cover immediately
after performing the necessary operation.
Also be sure to slide the platen back to its
original position.
•If a cover is to be placed over the copier,
be sure to turn OFF the power and allow
the copier to cool down beforehand.
•Should the copier not be operated for a
long period of time, unplug it from its
power source.
When Storing the Copier
Upright
•If the copier is to be stored upright with the
carrying handle on top, press the power
switch to OFF and let the copier cool down
beforehand. Stand the copier upright on a
flat, level surface so that it does not fall
over.
•If the copier has been stored upright,
move the platen all the way to the right
and then back to the center position by
hand before operating the copier.
Condensation
If the copier is brought from the cold
outdoors into a warm room, or if the room is
rapidly heated, condensation may form inside
the copier. This can adversely affect the
quality of your copy images (e.g., blacked-
out copies). When the copier is exposed to
such conditions, allow at least two hours for
the copier to fully adjust to room temperature
before attempting to use it.
 WARNING:
•If there is an unusual noise, smoke, or anything
else which causes concern, immediately turn
the power switch OFF and unplug the copier.
Then consult your service representative.
01_PC170-USA06.5.15, 18:26 10
 
						

							Getting Started
11
1
Installation PrecautionsAvoid direct sunlight and
place in a cool location.
Do not install the copier in front of a window
that receives direct sunlight.
Do not install the copier in a high
temperature, high humidity location such as
in front of a heater or humidifier.
Avoid abrupt changes in temperature and
humidity, such as those caused by proximity
to a heater.
■ Recommended Conditions:
Temperature of 59°C to 81°F
Relative Humidity of 25% to 75%
Image quality may be affected by low
temperatures if the copier has been left in
a cold location, be sure to allow more than
two hours for the copier to fully reach
room temperature before using it.
Installation Installation
Precautions Precautions
Copier performance is affected by
environmental conditions. Please
observe the following precautions
when selecting a site to install the
copier.Provide adequate
installation space.
It is necessary to provide adequate space
surrounding the copier to allow full
movement of the platen during copying.
■The minimum necessary operating
space:
32 
1/8 (width) ✕ 17 3/8 (depth)
Provide proper ventilation.
Avoid dusty locations or locations where
ammonia gas is emitted.
Place on a flat, level surface.
Do not install the copier on an incline or
uneven surface.
Do not install near
televisions or radios.
Do not place the copier near televisions,
radios or other similar electronic equipment.
The copier might interfere with reception.
Plug the copier into a separate power outlet
and maintain as much separation as
possible.
Power Supply
•This copier is designed only for use with
the power source shown on the marking
label on the back of the copier. If you are
unsure if your power source meets these
needs, check with your local power
company.
•Do not plug this copier into a multi-plug
power strip.
•Do not allow anything to sit on top of the
power cord.
 WARNING:
•If there is any unusual noise, smoke or anything
else which causes concern, immediately press
the power switch to OFF and unplug the copier
from its power source. Consult your service
representative.
Allow enough space in front of the power outlet
so that you can easily unplug the copier.
01_PC170-USA06.5.15, 18:26 11
 
						

							Getting Started
12
1
Carrying the Copier by
the Carrying Handle
Fold the trays up as shown in the
illustration, and insert the trays into the
opening between the disc and the platen
cover. Then pull out the carrying handle.
(See “Parts and Their Functions”,
on p. 15.)
Transporting Transporting
the Copier the Copier
Please observe the following
precautions when transporting
this copier.
•Before moving the copier, always
turn the power OFF and unplug
the copier from its power source.
•Before moving the copier, be sure
to disconnect the power cord
from the copier.
•If the copier will be subjected to
any vibrations (e.g., when
transporting long distances),
remove the cartridge from the
copier.
•Before operating the copier again
after it has been moved, slide the
platen all the way to the right and
then back to the center position
by hand.
Firmly grip the carrying handle. Slowly tilt
the copier upward. Then lift the copier.
When the unit is tilted the platen will
automatically lock into place.
Transporting the Copier
01_PC170-USA06.5.15, 18:26 12
 
						

							Getting Started
13
1
Transporting the Copier
Carrying the Copier by
the Sides
Secure the platen with packing tape.
Push in the carrying handle. Then fold up
the trays.
Insert the trays into the opening between
the disc and the platen cover.
Standing behind the copier as shown in
the illustration, firmly grasp the front and
rear sides of the copier and lift.
 REQUEST:
•Do not attempt to use the paper feeding slot,
exit slot, multi-stack tray or the copy tray as
handles. Attempting to carry the copier by
holding one of these may cause it to break off,
and thus cause the handler to drop and damage
the copier.
 REQUEST:
•Make sure that the trays are set correctly under
the disc on the platen cover.
•Double check to make sure the trays are set
correctly under the disc on the platen cover.
•If transporting the copier over a long distance
secure the platen cover with packing tape and
remove the cartridge. (See p.14.)
•When transporting the copier take extra care not
to subject it to vibrations or shock.
•If you need to set the copier down for a while,
place it upright on a flat level surface with the
carrying handle on top.
•When lowering the copier to a horizontal
position (installation position), do so slowly.
01_PC170-USA06.5.15, 18:26 13
 
						

							Getting Started
14
1
Transporting the
Copier by Car
Place the copier on a stable
surface (i.e., on the seat) inside
the car.
 REQUEST:
•Remove the cartridge from the copier and place
it in its original shipping box. Then secure the
platen with packing tape. Finally place the
copier in its original shipping box.
•Do not leave the copier inside a car for long
periods of time; the temperature inside a car can
exceed the recommended extremes.
•Avoid rough roads; excessive vibrations may
damage the copier.
•Do not place the copier in direct sunlight. Use a
cover if necessary.
Transporting the Copier
01_PC170-USA06.5.15, 18:26 14
 
						

							Getting Started
15
1
Parts and Their Functions Parts and Their Functions
Main Unit
Platen Cover
Top Cover Release Button
(See pp. 22, 44 and 46.)
Press to open the top cover.
Parts and Their Functions
Platen Glass
Left Cover (See p.45.)
Open when removing jammed
paper from the output area.
Copy Tray
Multi-stack Tray
Exit Slot
Up to 50 sheets of copy paper can be loaded in the multi-stack tray at a time.
Left Cover Release Button
(See p. 45.)
Press to open the left cover.
01_PC170-USA06.5.15, 18:26 15
 
						

							Getting Started
16
1
Sealing 
Tape Grip
Top Cover
Open when changing the
cartridge, clearing paper jams
or cleaning the roller.Paper Feed Guides
 Adjust to fit paper size.
Parts and Their FunctionsCartridge
Carrying Handle
Pull out to use when transporting
the copier. Multi-stack Tray Exposure Recalibration Switch
Slide up or down to adjust the copy
exposure to one of three steps to
accommodate dark,  normal or light
originals. Power Switch Multi-stack Tray Paper Feeding Slot Power Cord Connector
(rear right)
Copy Tray
Disc
01_PC170-USA06.5.15, 18:26 16
 
						

							Getting Started
17
1
CAAE
: Misfeed error / Load paper
: Paper jam
: Error
: Error
: Error then
then
then
Error indications
Parts and Their Functions
Control Panel
Number of Copies/Error
Message Indicator
Shows the number of copies
selected or any error messages.
A (Auto) Indicator
Lights up when the Auto
Exposure Control is selected.
Exposure Adjustment Lever
Slide to manually adjust the copy
exposure setting (lightness/
darkness).
The AE Key
Press to select or cancel the
Auto Exposure Control.
Paper Jam Indicator
Flashes when copy paper is
jammed inside the copier.Number of Copies Key
Press to select the desired
number of copies.Clear/Stop Key
Press to return the number of
copies to one, or to stop the
copier while copying.Start Key
Press to start copying.
01_PC170-USA06.5.15, 18:26 17
 
						

							Getting Started
18
1
Installing the Installing the
Copier Copier
Checking the Package
Contents
Remove the copier and the
accessories from the shipping
box. Use the following checklist
to make sure you have received
all the necessary accessories
included with your copier.
Registration Card 1
Power Cord 1
Operator’s Manual 1
Cartridge 1
Muliti-stack tray 1
Copy tray 1
Item Quantity
Installation Procedure
Before installing the copier be
sure to check the safety of the
power source. Then proceed with
the following procedure.
Although the starter cartridge
comes already installed in the
main unit, it is necessary to
remove the sealing tape from the
cartridge before use.
The cartridge cannot be used if
the seal is not removed.
(See “Installation Precautions”,
on p. 11 and “Replacing and
Storing Cartridges”, on p. 19.)
Remove the copier from its shipping bag
and gently remove all the packing tape
attached to the copier.
Slightly slide the copy tray and the multi-
stack tray out from the opening between
the disc and the platen cover, and then
open the trays fully.
Slide the platen to the left, press the top
cover release button and lift open the top
cover. Grip the end of the cartridge, and
pull it out of the copier.
(See “Replacing and Storing Cartridges”,
on p. 19.)
Hold the cartridge level so that the side
with the written instructions is facing
upward.
Installing the Copier
01_PC170-USA06.5.15, 18:26 18