Canon network camera VBS805D User Manual

[Event] Setting Video Record, Volume Detection, External Device Output/Input and Timer
61
Setting Page
3
(8) [Ongoing ON Event Operation]
Select the operation to be performed while a volume 
detection event is in progress. This can be set when 
[ON Event Operation] is set to [Enable].
If [Enable] is selected, (10) [Video Record] and 
(11) [E-mail Notification] will be executed according to 
their settings during the volume detection event.
(9) [Preset]
If a preset is specified, the camera will orient...

62
open, and an inactive event occurs when the 
terminals close.
(3) [Active Event Operation] 
Select the operation to be performed upon an active 
event. If [Enable] is selected, (6) [Preset], (7) [Video 
Record] and (8) [E-mail Notification] will be executed 
according to their settings upon an active event. 
(4) [Inactive Event Operation] 
Select the operation to be performed upon an inactive 
event. If [Enable] is selected, (6) [Preset], (7) [Video 
Record] and (8) [E-mail Notification] will be...

[Event] Setting Video Record, Volume Detection, External Device Output/Input and Timer
63
Setting Page
3
(8) [Day/Night Mode Switching]
Select the Day/Night Mode switching behavior when a 
timer event is triggered. 
Select [Switch to Day Mode] to switch to Day Mode at 
the start time, and Night Mode at the end time.
Select [Switch to Night Mode] to switch to Night Mode 
at the start time, and Day Mode at the end time.
Select [Disable] to disable Day/Night Mode switching.
Note
When using timers that run...

64
Administrator Password
For details on [Password] and [Confirm Password], 
please refer to [Network] > [Administrator Password] 
(p. 40) .
[Administrator Password] is the same. If you set one 
[Administrator Password], the setting will be reflected in 
the other [Administrator Password].
Authorized User Account
(1) [User Name], [Password] 
Enter the user name and password and then click 
[Add]. The authorized user will be added to the user 
list. 
The user name can consist of up to 15 (single-byte)...

[Access Control] Setting User Access Privileges
65
Setting Page
3
Note
If the same address is duplicated, the policy for the address that 
appears highest on the list will be applied. 
IPv6 Host Access Restrictions
(1) [Apply Host Access Restrictions] 
Set IPv6 host access restrictions to [Disable] or 
[Enable]. 
(2) [Default Policy] 
If IPv6 host access restrictions are applied, select 
[Authorize Access] or [Prohibit Access] for the default 
policy. 
(3) [Prefix / Prefix Length] 
Create a list of...

66
IPsec 
(1) [IPsec] 
Key settings for use with IPsec can be selected as 
[Auto Key Exchange] or [Manual].
Auto Key Exchange Settings
(1) [IPsec SA Encryption Algorithm] 
Set the IPsec SA encryption algorithm to [AES-
>3DES], [AES->3DES->DES] or [AES->3DES->DES-
>NULL]. 
The specified algorithm will be checked for an 
applicable encryption algorithm starting from the left. 
(2) [IPsec SA Authentication Algorithm] 
Set the IPsec SA authentication algorithm to 
[HMAC_SHA1_96] or [HMAC_SHA1_96->...

[IPsec] Setting IPsec
67
Setting Page
3
(8) [IKE Pre-Shared Key] 
Enter the pre-shared key for IKE (auto key exchange) 
(up to 127 characters). 
Note
If auto key exchange is used, it will take approximately 5 to 10 
seconds before communication with the camera starts. 
IPsec Set (Manual) 
IPsec Sets 1 to 5 are available, and you can specify IPsec 
settings for one communication device for each IPsec Set. 
(1) [IPsec Set] 
Set IPsec Set to [Disable], [Enable in IPv4] or [Enable 
in IPv6]. 
(2) [IPsec...

68
identifying the SA, be careful not to specify an 
inbound SPI whose value is already used in the SPI for 
other ESP. 
zIf [Security Protocol] was set to [AH] or [ESP and AH] in 
(5), (16) [SA AH Authentication Algorithm] to (20) [SA 
AH SPI (inbound)] must be set. 
(16)[SA AH Authentication Algorithm] 
Set the AH authentication algorithm to 
[HMAC_SHA1_96] or [HMAC_MD5_96] according to 
the authentication algorithm supported by the device 
to connect to. 
(17)[SA AH Authentication Key (outbound)] 
Set...

69
3
Setting Page
Certificates
(1) [Create Self-Signed Certificate] 
After entering each of the following settings, click 
[Exec] to create a self-signed certificate. Follow the 
instructions in the message and reboot. The certificate 
created will take effect after rebooting. 
Note
Creating a certificate takes time, so it is recommended that you 
stop video transmission and upload processes.
(2) [Certificate Status] 
If no certificate is installed, [Not Installed] will appear. 
If a certificate is...

70
(6) [Display Server Certificate Details] 
Click [Exec] to view the details of the server 
certificate. 
(7) [Display Self CA Certificate] 
Used for the purpose of testing SSL communications, 
but otherwise not normally used. 
(8) [Backup] 
Click [Exec] to perform a backup of the certificates 
and private key. This operation can only be performed 
when [HTTPS Connection Policy] is set to use [HTTPS] 
or [HTTP and HTTPS], and SSL communications are in 
use.
(9) [Restore] 
Installs the certificates and...