Canon network camera VBS805D User Manual

							[Event] Setting Video Record, Volume Detection, External Device Output/Input and Timer
61
Setting Page
3
(8) [Ongoing ON Event Operation]
Select the operation to be performed while a volume 
detection event is in progress. This can be set when 
[ON Event Operation] is set to [Enable].
If [Enable] is selected, (10) [Video Record] and 
(11) [E-mail Notification] will be executed according to 
their settings during the volume detection event.
(9) [Preset]
If a preset is specified, the camera will orient 
automatically to the specified preset position when a 
volume detection event occurs. To use presets, it is 
necessary to set the presets with the Preset Setting 
Tool under Admin Tools (p. 96). If there is no need for 
additional camera operation, select [None]. 
(10)[Video Record]
Specify the video record action. If [Enable] is 
selected, video will be transmitted to the destination 
selected in [Video Record Action] (p. 60) when a 
volume detection event occurs.
(11)[E-mail Notification] 
Select the e-mail notification operation to be 
performed. If [Enable] is selected, e-mail notification 
is performed when a volume detection event occurs. 
To use this function, [Upload] > [E-mail Notification ] 
must also be set (p. 57).
(12)[External Device Output for ON Event]
Select whether external device output is active or 
inactive upon an ON event. Select [Disable] to disable 
external device output.
(13)[External Device Output for OFF Event]
Select whether external device output is active or 
inactive upon an OFF event. Select [Disable] to 
disable external device output.
External Device Output
(1) [Operation Mode]
Select the normal (inactive) circuit condition.
When [Normally Open] is selected, the output 
terminals remain in the open state during normal operation, and the terminals close upon an active 
event and open upon an inactive event.
When [Normally Close] is selected, the output 
terminals remain in the closed state during normal 
operation, and the terminals open upon an active 
event and close upon an inactive event.
(2) [Active Output Format]
Select [Pulse] or [Continuous] for the external device 
output format.
(3) [Pulse Output Time (sec)]
Enter the pulse output time in the range of 1 to 120 
(sec.). This setting is available when [Active Output 
Format] is [Pulse].
Note
[Normally Open] means that the contacts are normally in the 
open state (that the circuit is non-conductive), and [Normally 
Close] means that the contacts are normally in the closed state 
(that the circuit is conductive).
External Device Input 
(1) [External Device Input Event] 
Set external device input events to [Disable] or 
[Enable]. 
(2) [Operation Mode]
Select the circuit condition of the connected external 
device.
When [Normally Open] is selected, an active event 
occurs when the terminals of the external device 
close, and an inactive event occurs when the 
terminals open.
When [Normally Close] is selected, an active event 
occurs when the terminals of the external device 
Important
 For notes on use of volume detection, see “Safety 
Precautions” in “Precautions for Use of Built-In Camera 
Functions and Included Software” (p. 7).
 When Admin Viewer/VB Viewer has camera control 
privileges, those camera control privileges are released if the 
camera is moved to a preset position, specified in the 
[Preset] settings (VB-S30D/VB-S31D only), by a volume 
detection event operation.
Important
When [Active Output Format] is set to [Pulse] and a timer is 
used, a single contact output is controlled when the timer starts.
Normally Open
Active Event
Inactive Event1 (Terminals close)
0 (Terminals open)
Normally Close
Inactive Event
Active Event1 (Terminals close)
0 (Terminals open) 
						

							62
open, and an inactive event occurs when the 
terminals close.
(3) [Active Event Operation] 
Select the operation to be performed upon an active 
event. If [Enable] is selected, (6) [Preset], (7) [Video 
Record] and (8) [E-mail Notification] will be executed 
according to their settings upon an active event. 
(4) [Inactive Event Operation] 
Select the operation to be performed upon an inactive 
event. If [Enable] is selected, (6) [Preset], (7) [Video 
Record] and (8) [E-mail Notification] will be executed 
according to their settings upon an inactive event.
(5) [Ongoing Active Event Operation]
Select the operation to be performed while an active 
event is in progress. This can only be set when [Active 
Event Operation] is set to [Enable].
If [Enable] is selected, (7) [Video Record] and (8) [E-
mail Notification] will be executed according to their 
settings during the active event.
(6) [Preset]
  
If a preset is specified, the camera will automatically 
orient to the specified preset position when an 
external device input event occurs. To use presets, it 
is necessary to set presets with the Preset Setting Tool 
under Admin Tools (p. 96). If there is no need for 
additional camera operation, select [None]. 
(7) [Video Record]
Specify the video record action. If [Enable] is 
selected, video will be transmitted to the destination 
selected in [Video Record Action] (p. 60) when an 
external device input event occurs.
(8) [E-mail Notification] 
Select the e-mail notification operation to be 
performed. If [Enable] is selected, e - m ai l  
notification will be performed when an external 
device input event occurs. To use this function, 
[Upload] > [E-mail Notification] must also be set 
(p. 57).
(9) [External Device Output for Active Event]
Select whether external device output is active or 
inactive upon an active event. Select [Disable] to 
disable external device output.
(10)[External Device Output for Inactive Event]
Select whether external device output is active or 
inactive upon an inactive event. Select [Disable] to 
disable external device output.
(11)[Day/Night Mode Switching]
Select the Day/Night Mode switching behavior when 
an external device input event is triggered.
When [Switch to Day Mode] is selected, switches to 
Day Mode when an active event is triggered, and 
switches to Night Mode when an inactive event is 
triggered.When [Switch to Night Mode] is selected, switches to 
Night Mode when an active event is triggered, and 
switches to Day Mode when an inactive event is 
triggered.
Select [Disable] to disable Day/Night Mode switching.
Timer
(1) [Timer Event] 
Select [Disable] or [Enable] for timer event. 
(2) [Start Time] 
Set the start time of the timer event in 24-hour format. 
(3) [End Time]
Set the end time of the timer event in the 24-hour 
format.
(4) [Repeat Interval] 
Select [1 sec.] [5 sec.] [10 sec.] [30 sec.] [1 min.] [5 min.] 
[10 min.] [15 min.] [20 min.] [30 min.] [1 hour] [3 hours] 
[6 hours] or [12 hours] for the timer event repeat intervals. 
Select [None] if an operation need not be repeated.
(5) [Video Record]
Specify the video record action. When [Enable] is 
selected, video will be transmitted to the destination 
selected in [Video Record Action] (p. 60) when a timer 
event occurs.
(6) [E-mail Notification] 
Select the e-mail notification operation to be 
performed. If [Enable] is selected, e-mail notification 
is performed when a timer event occurs. To use this 
function, [Upload] > [E-mail Notification] must also be 
set (p. 57).
(7) [External Device Output]
Select whether external device output is active or 
inactive when a timer event occurs. Select [Disable] to 
disable output to an external device.
Important
 When [Day/Night] in the Admin Viewer is set to [Auto], Day/
Night Mode switching will not happen when an external 
device input event is triggered (p. 144).
 Camera control privileges are released if any of the following 
actions occur while the Admin Viewer/VB Viewer has camera 
control privileges.
– If the camera angle is moved according to 
the [Preset] settings
– If the Day/Night Mode is switched using [Day/Night Mode 
Switching]. 
						

							[Event] Setting Video Record, Volume Detection, External Device Output/Input and Timer
63
Setting Page
3
(8) [Day/Night Mode Switching]
Select the Day/Night Mode switching behavior when a 
timer event is triggered. 
Select [Switch to Day Mode] to switch to Day Mode at 
the start time, and Night Mode at the end time.
Select [Switch to Night Mode] to switch to Night Mode 
at the start time, and Day Mode at the end time.
Select [Disable] to disable Day/Night Mode switching.
Note
When using timers that run continuously for 24 hours with a 
[Repeat Interval] of 30 seconds or less, set the timer start and 
end times so the timers can run continuously.
Example:
Important
 [Day/Night Mode Switching] can only be set in [Timer 1].
 [External Device Output] and [Day/Night Mode Switching] do 
not support [Repeat Interval].
 When [Day/Night] in the Admin Viewer is set to [Auto], Day/
Night Mode switching will not happen when a timer event is 
triggered (p. 144).
 If the [Day/Night Mode Switching] settings switch Day/Night 
Mode while the Admin Viewer/VB Viewer is assigned camera 
control, control will be released.
Timer[Start Time][End Time][Repeat Interval]
[Timer 1] 0:00 12:00 10 sec
[Timer 2] 12:00 0:00 10 sec 
						

							64
Administrator Password
For details on [Password] and [Confirm Password], 
please refer to [Network] > [Administrator Password] 
(p. 40) .
[Administrator Password] is the same. If you set one 
[Administrator Password], the setting will be reflected in 
the other [Administrator Password].
Authorized User Account
(1) [User Name], [Password] 
Enter the user name and password and then click 
[Add]. The authorized user will be added to the user 
list. 
The user name can consist of up to 15 (single-byte) 
characters using A to Z, a to z, 0 to 9, “-” (hyphen) and 
“_” (underscore). 
The password can consist of 6 to15 (single-byte) 
ASCII characters (space or printable characters). 
(2) [User List] 
A list of authorized users is shown. User authorities 
can be set for these users. Up to 50 users can be 
registered in addition to the Administrator (root). 
Also, the user list can be sorted using the S T 
buttons on the right. 
To delete a user, select the applicable user from the 
user list and then click [Delete]. User Authority
[Privileged Camera Control], [Camera Control], [Video 
Distribution], [Audio Distribution] 
Set the user authorities of authorized users and guest 
users. Select the checkboxes corresponding to the 
items you want to permit for each user. 
Note
Authorized users have higher authorities than guest users. 
For details, see “User Authorities and Camera Control Privileges” 
(p. 126).
IPv4 Host Access Restrictions
(1) [Apply Host Access Restrictions] 
Set IPv4 host access restrictions to [Disable] or 
[Enable]. 
(2) [Default Policy] 
If IPv4 host access restrictions are applied, select 
[Authorize Access] or [Prohibit Access] for the default 
policy. 
(3) [Network Address / Subnet] 
Create a list of permitted hosts and restricted hosts 
and set IPv4 address access for each host to [Yes] or 
[No]. 
You can specify the subnet and set access 
restrictions by network or host. 
If access is prohibited, access to all ports is 
restricted. 
[Access Control] Setting User Access Privileges 
The following can be set here. 
 Administrator Password
Set the administrator password.
 Authorized User Account
Register who can access this camera. 
 User Authority
Set the authorities for authorized users and guest 
users. 
 IPv4 Host Access Restrictions
Specify the hosts from which IPv4 access is 
permitted and restricted. 
 IPv6 Host Access Restrictions
Specify the hosts from which IPv6 access is 
permitted and restricted. 
Important
 To prohibit access via a proxy server in HTTP connection, a 
proxy server address must be set. 
 If host access restriction is set mistakenly, access to the 
setting pages themselves may be prohibited, in which case 
restoring the factory default settings will become the only 
means for recovery.  
						

							[Access Control] Setting User Access Privileges
65
Setting Page
3
Note
If the same address is duplicated, the policy for the address that 
appears highest on the list will be applied. 
IPv6 Host Access Restrictions
(1) [Apply Host Access Restrictions] 
Set IPv6 host access restrictions to [Disable] or 
[Enable]. 
(2) [Default Policy] 
If IPv6 host access restrictions are applied, select 
[Authorize Access] or [Prohibit Access] for the default 
policy. 
(3) [Prefix / Prefix Length] 
Create a list of permitted hosts and restricted hosts 
and set IPv6 address access for each host to [Yes] or 
[No]. 
You can specify the prefix length and set access 
restriction by network or host. 
If access is prohibited, access to all ports is 
restricted.  
						

							66
IPsec 
(1) [IPsec] 
Key settings for use with IPsec can be selected as 
[Auto Key Exchange] or [Manual].
Auto Key Exchange Settings
(1) [IPsec SA Encryption Algorithm] 
Set the IPsec SA encryption algorithm to [AES-
>3DES], [AES->3DES->DES] or [AES->3DES->DES-
>NULL]. 
The specified algorithm will be checked for an 
applicable encryption algorithm starting from the left. 
(2) [IPsec SA Authentication Algorithm] 
Set the IPsec SA authentication algorithm to 
[HMAC_SHA1_96] or [HMAC_SHA1_96-> 
HMAC_MD5_96]. 
The specified algorithm will be checked for an 
applicable authentication algorithm starting from the 
left. 
(3) [IPsec SA Validity Period (min)] 
Set the duration of validity for IPsec SA (factory default 
setting is [480]). 
(4) [ISAKMP SA Encryption Algorithm] 
Set the SA encryption algorithm for use with auto key 
exchange protocol IKE to [AES->3DES] or [AES-> 
3DES->DES]. 
(5) [ISAKMP SA Authentication Algorithm] 
Set the SA authentication algorithm for use with auto 
key exchange protocol IKE to [SHA1] or [SHA1-
>MD5]. (6) [DH Group] 
Select the key generation information for the DH 
algorithm that will be used for key exchange via auto 
key exchange protocol IKE. The security level 
increases with higher group numbers.
(7) [ISAKMP SA Validity Period (min)] 
Set the duration of validity for ISAKMP SA (factory 
default setting is [480]). 
IPsec Set (Auto Key Exchange) 
IPsec Sets 1 to 5 are available, and you can specify IPsec 
settings for one communication device for each IPsec Set. 
(1) [IPsec Set] 
Set IPsec Set to [Disable], [Enable in IPv4] or [Enable 
in IPv6]. 
(2) [IPsec Mode] 
Set IPsec mode to [Tunnel Mode] or [Transport 
Mode]. 
(3) [Destination IPv4 Address], [Destination IPv6 Address] 
Enter the IP address of the connection destination. 
(4) [Source IPv4 Address], [Source IPv6 Address] 
Enter the IP address of the source. 
(5) [Security Protocol] 
Set the IPsec protocol to [ESP], [AH] or [ESP and AH]. 
If [ESP] is selected, enter only the setting items 
relating to ESP. 
If [AH] is selected, enter only the setting items relating 
to AH.
If [ESP and AH] is selected, enter all setting items. 
(6) [Security Gateway IPv4 Address], [Security Gateway 
IPv6 Address]
If IPsec mode is set to [Tunnel Mode] in (2), set the IP 
address of the security gateway. 
(7) [Destination Subnet Mask Length] (IPv4), [Destination 
Prefix Length] (IPv6) 
This setting is required only if IPsec mode is set to 
[Tunnel Mode] in (2). 
If IPv6 is used, enter a desired prefix length for the 
connection destination in the range of 16 to 128. 
If IPv4 is used, enter a desired length in the range of 1 
to 32. 
[IPsec] Setting IPsec
The following can be set here. 

Set the IPsec setting method. 
 Auto Key Exchange Settings
Set auto key exchange. 
Set
IP security can be specified through auto key 
exchange or manual setting with up to five 
communicating devices.  
						

							[IPsec] Setting IPsec
67
Setting Page
3
(8) [IKE Pre-Shared Key] 
Enter the pre-shared key for IKE (auto key exchange) 
(up to 127 characters). 
Note
If auto key exchange is used, it will take approximately 5 to 10 
seconds before communication with the camera starts. 
IPsec Set (Manual) 
IPsec Sets 1 to 5 are available, and you can specify IPsec 
settings for one communication device for each IPsec Set. 
(1) [IPsec Set] 
Set IPsec Set to [Disable], [Enable in IPv4] or [Enable 
in IPv6]. 
(2) [IPsec Mode] 
Set IPsec mode to [Tunnel Mode] or [Transport 
Mode]. 
(3) [Destination IPv4 Address], [Destination IPv6 Address] 
Enter the IP address of the connection destination. 
(4) [Source IPv4 Address], [Source IPv6 Address] 
Enter the IP address of the source. 
(5) [Security Protocol] 
Set the IPsec protocol to [ESP], [AH] or [ESP and AH]. 
If [ESP] is selected, enter only the setting items 
relating to ESP. 
If [AH] is selected, enter only the setting items relating 
to AH.
If [ESP and AH] is selected, enter all setting items. 
(6) [Security Gateway IPv4 Address], [Security Gateway 
IPv6 Address]
If [IPsec Mode] is set to [Tunnel Mode] in (2), set the 
IP address of the security gateway. (7) [Destination Subnet Mask Length] (IPv4), [Destination 
Prefix Length] (IPv6)
This setting is required only if [IPsec Mode] is set to 
[Tunnel Mode] in (2).
If IPv6 is used, enter a desired prefix length for the 
connection destination in the range of 16 to 128. 
If IPv4 is used, enter a desired length in the range of 1 
to 32. 
zIf [Security Protocol] is set to [ESP] or [ESP and AH] in 
(5), (8) [SA ESP Encryption Algorithm] to (15) [SA ESP 
SPI (inbound)] must be set. 
(8) [SA ESP Encryption Algorithm] 
Set the ESP encryption algorithm to [AES], [3DES], 
[DES] or [NULL] according to the encryption 
algorithm supported by the device to connect to. 
Normally [AES] or [3DES] is recommended. 
(9) [SA ESP Authentication Algorithm] 
Set the ESP authentication algorithm to 
[HMAC_SHA1_96], [HMAC_MD5_96] or [No 
Authentication] according to the authentication 
algorithm supported by the device to connect to. 
If [ESP] is used alone, [No Authentication] cannot be 
selected.
(10)[SA ESP Encryption Key (outbound)] 
Set the SA encryption key for outbound. If [AES], 
[3DES] or [DES] was selected in (8), set a 128-bit, 
192-bit or 64-bit hexadecimal, respectively. This item 
need not be set if [NULL] was selected.
(11)[SA ESP Authentication Key (outbound)] 
Set the SA authentication key for outbound. If 
[HMAC_SHA1_96] or [HMAC_MD5_96] was selected 
in (9), set a 160-bit or 128-bit hexadecimal, 
respectively. This item need not be set if [No 
Authentication] was selected. 
(12)[SA ESP SPI (outbound)] 
Set the SA SPI value for outbound. 
Set a desired value in the range of 256 to 
4294967295.
(13)[SA ESP Encryption Key (inbound)] 
Set the SA encryption key for inbound. 
If [AES], [3DES] or [DES] was selected in (8), set a 
128-bit, 192-bit or 64-bit hexadecimal, respectively. 
This item need not be set if [NULL] was selected.
(14)[SA ESP Authentication Key (inbound)] 
Set the SA authentication key for inbound. 
If [HMAC_SHA1_96] or [HMAC_MD5_96] was 
selected in (9), set a 160-bit or 128-bit hexadecimal, 
respectively. This item need not be set if [No 
Authentication] was selected. 
(15)[SA ESP SPI (inbound)] 
Set the SA SPI value for inbound. 
Set a desired value in the range of 256 to 
4294967295. Since this setting is used as an ID for 
Important
If the camera is rebooted during auto key exchange 
communication, a connection error may result after rebooting. 
In this case, connect again.  
						

							68
identifying the SA, be careful not to specify an 
inbound SPI whose value is already used in the SPI for 
other ESP. 
zIf [Security Protocol] was set to [AH] or [ESP and AH] in 
(5), (16) [SA AH Authentication Algorithm] to (20) [SA 
AH SPI (inbound)] must be set. 
(16)[SA AH Authentication Algorithm] 
Set the AH authentication algorithm to 
[HMAC_SHA1_96] or [HMAC_MD5_96] according to 
the authentication algorithm supported by the device 
to connect to. 
(17)[SA AH Authentication Key (outbound)] 
Set the SA authentication key for outbound. If 
[HMAC_SHA1_96] or [HMAC_MD5_96] was selected 
in (16), set a 160-bit or 128-bit hexadecimal, 
respectively. 
(18)[SA AH SPI (outbound)] 
Set the SA SPI value for outbound. 
Set a desired value in the range of 256 to 
4294967295.
(19)[SA AH Authentication Key (inbound)] 
Set the SA authentication key for inbound. If 
[HMAC_SHA1_96] or [HMAC_MD5_96] was selected 
in (16), set a 160-bit or 128-bit hexadecimal, 
respectively. 
(20)[SA AH SPI (inbound)] 
Set the SA SPI value for inbound. 
Set a desired value in the range of 256 to 
4294967295. Since this setting is used as an ID for 
identifying the SA, be careful not to specify an 
inbound SPI whose value is already used in the SPI for 
another AH. 
Note
If IPsec is used, video transmission performance drops.
Important
 To run this camera with IPsec, the communicating devices 
and network must be set beforehand. Contact your System 
Administrator for these settings. 
 When connecting with IPsec, set the camera IP address 
manually.
For IPv4 addresses, use addresses set with [Network] > 
[IPv4 Address Setting Method] > [Manual].
For IPv6 addresses, use addresses set with [Network] > 
[IPv6 Address (Manual)].
 If any setting is changed from the [IPsec] menu, the camera 
may become inaccessible from the active web browser. 
Check beforehand the precautions in “Important” in “[Reboot 
Item] Setting Items Requiring Rebooting” (p. 76). 
						

							69
3
Setting Page
Certificates
(1) [Create Self-Signed Certificate] 
After entering each of the following settings, click 
[Exec] to create a self-signed certificate. Follow the 
instructions in the message and reboot. The certificate 
created will take effect after rebooting. 
Note
Creating a certificate takes time, so it is recommended that you 
stop video transmission and upload processes.
(2) [Certificate Status] 
If no certificate is installed, [Not Installed] will appear. 
If a certificate is installed, the validity period for the 
certificate will appear. 
(3) [Country (C)] 
Enter the country code. 
(4) [State/Province (ST)], [Locality (L)], [Organization (O)], 
[Organizational Unit (OU)], [Common Name (CN)] 
Enter state/province name, locality, organization 
name, organizational unit and common name in ASCII 
characters (spaces or printable characters). Enter a 
FQDN format host name, etc. to set the common 
name (required). 
(5) [Validity Period Start Date], [Validity Period End Date] 
Set the validity period of the certificate to be created in 
the range of 2001/01/01 to 2031/12/31 (required when 
creating a self-signed certificate). Certificate Management
(1) [Generate Certificate Signing Request] 
Click [Exec] to create server private key and generate 
a certificate signing request. Once processed, the 
certificate signing request will appear in a separate 
window. 
Note
Generating a certificate signing request takes time, so it is 
recommended that you stop video transmission and upload 
processes.
(2) [Display Certificate Signing Request] 
Click [Exec] to view the details of the certificate 
signing request. 
(3) [Install Server Certificate] 
Perform this operation to install a server certificate. 
Click [Browse] to select the certificate file for 
installation, then click [Exec]. The certificate installed 
will take effect after rebooting. 
(4) [Install Intermediate Certificate] 
Perform this operation to install an intermediate 
certificate. Select the certificate file to be installed 
using [Browse] and click [Exec]. The installed 
certificate will take effect after rebooting. 
Note
To install an intermediate certificate and a primary intermediate 
certificate, use a text editor or similar software to place them in 
the same file and install them as an intermediate certificate.
(5) [Delete Certificate] 
Click [Exec] to delete the server certificate. However, 
if SSL communications are enabled, the certificate 
cannot be deleted. Set [HTTPS Connection Policy] to 
[HTTP] before deleting a certificate. The deletion will 
take effect after rebooting. 
[SSL/TLS] Setting HTTP Communication Encryption
The following can be set here. 
 Certificates
Create an SSL/TLS certificate. 
 Certificate Management
Manage the SSL/TLS certificate. 
 Encrypted Communications
Set the encrypted communication.Important
With regard to security, use a self-signed certificate where 
complete security does not need to be ensured through 
operation tests, etc. For system operation, it is recommended 
that you acquire and install a certificate issued by a CA. 
						

							70
(6) [Display Server Certificate Details] 
Click [Exec] to view the details of the server 
certificate. 
(7) [Display Self CA Certificate] 
Used for the purpose of testing SSL communications, 
but otherwise not normally used. 
(8) [Backup] 
Click [Exec] to perform a backup of the certificates 
and private key. This operation can only be performed 
when [HTTPS Connection Policy] is set to use [HTTPS] 
or [HTTP and HTTPS], and SSL communications are in 
use.
(9) [Restore] 
Installs the certificates and private key from 
backup. Click [Browse] to select the backup file, 
then click [Exec]. This operation can only be 
performed when [HTTPS Connection Policy] is set to 
use [HTTPS] or [HTTP and HTTPS], and SSL 
communications are in use. The restored certificate 
will take effect after rebooting. 
Encrypted Communications
(1) [HTTPS Connection Policy] 
Select whether or not to use SSL communications with 
HTTPS connections.
To not use SSL communications, select [HTTP].
To use SSL communications, select [HTTPS] or [HTTP 
and HTTPS]. SSL connections will be possible after 
rebooting. 
When [HTTPS] is selected, even HTTP connections 
will be redirected to HTTPS and SSL communications 
will be used.
Note
 It may take a few minutes to generate an SSL key. 
 Depending on the type of the certificate being installed on the 
camera, a dialog box may appear indicating that the web 
browser has accepted the certificate and a connection can be 
made.
If the dialog box does not appear, register the CA certificate in 
the web browser.
Important
 Even if SSL communications are set here to be used, they will 
not be used if the certificate is not installed.
 Video transmission performance will drop, if SSL 
communications are used. When [HTTPS] is selected, 
communication with RM is not possible.