Canon network camera VBR10VE User Manual

							Admin Tools
6
221
Detection Status for Moving Object Detection
All moving objects detected are shown with contour lines.
If a moving object is smaller than [Object Size (%)], its contour lines are white.
If the moving object is larger than [O bject Size (%)], its contour lines take  on the same color as the detection area, 
indicating that “d etected” mode has been triggered.
Note
If an object is placed in or removed from  the moving object detection area, “detected”  mode will be triggered for Moving Object 
Detection.
 How to Configure Abandoned Object Detection
Set the area you want to detect a pl aced object in as a detection area.
This determines how large the abandoned object must be in relation to the detection area you set in step 2 for 
abandoned object detection to be triggered.
When the setting values or slider is  changed, an indicator frame representing the object size is displayed for one 
second in the center of the video display area allowing y ou to check the size ratio while specifying the setting.
Contour Lines of Detected Moving Object
1Select [Rectangular] or [Polygonal].
2Use the video display area to configure the area where you would like to detect abandoned objects (P. 219).
3Configure the size of the object needed for triggering detection in [Object Size (%)].
4Configure [Duration ( Sec)] for the time required for an obje ct to be detected as an abandoned object.
Object Size Indicator
Detection Area 
						

							222
Detection Status for Abandoned Object Detection
All moving objects detected are shown with contour lines.
If [Object Size (%)] and [Dur ation (Sec)] are not exceeded, contour lines are white.
If both [Object Size (%)] and [Duration (Sec)] are exceeded, t he contour lines take on the same color as the detection 
area, indicating that  “detected” mode ha s been triggered.
How to Configure Remo ved Object Detection
Set an area around the target objects, for Removed Object De tection. If there are multiple objects for which you want 
to enable detection, be sure to configur e Removed Object Detection for each object.
Temporarily remove the target object for removed object detection from the video display area. ▼
Click [Restart intelligent function] (P. 235).
The background image is generated
▼
Return the target object to its original position. ▼
Click [Quick setting].
An outline of the object is drawn using a polygon with up to 32 vertices.
If there are multiple objects detect ed, the outline is drawn around the  object occupying the largest area.
▼
Click [Restart intelligent function] again.
Contours of Moving Object Detected as Abandoned
1Select [Rectangular] or [Polygonal].
2Use the video display area to configure an area along the  contours of the object you do not want removed (P. 219).
You can also click [Quick sett ing] and follow the steps below to configure the area.
Set detection area 
						

							Admin Tools
6
223
Detection Status for Removed Object Detection
All moving objects detected are shown with contour lines.
As long as [Duration (Sec)] is no t exceeded, contour lines are white.
When [Duration (Sec)] is exceeded, contour lines take on th e same color as the detection area, indicating that 
“detected” mode has been triggered.
 How to Configure Camera Tampering Detection
For [Camera Tampering Detection], the en tire video display area is the detection area. The area cannot be changed.
In [Change Ratio (%)], you can set the ratio of screen chang e for tampering detection to be determined in relation to 
the entire video display area.
When the setting values or slider is c hanged, an indicator frame representing the ar ea of the entire video display area 
that can be obstructed is displayed for one second in the center of the video  display area allowing you to check while 
specifying the setting.
Detection  Status for Camera Ta mpering Detection
All moving objects detected are shown with contour lines.
If an object is smaller than [Change Ratio (%)], its contour lines are white.
If the obscured area in the video exceeds [Change Ratio (% )], contour lines take on the same color as the detection 
area, indicating that  “detected” mode ha s been triggered.
Important
Set detection areas for removed object detection so that they  precisely match the contours of the target object. Influence from the 
target object’s shadow or adjacent objects may result in the ta rget object being recognized as larger than it actually is and w ill not 
trigger removed object detection. In this occurs, reconfigure  the detection area to outline the recognized target object.
3Configure [Duration (Sec)] for time required for an object  to be detected as a removed object.
Contours of Moving Object Detected as Removed
Change ratio indicator 
						

							224
Note
Detection will not be possible for three seconds after the change ratio for camera tampering detection is changed, or when 
switching into camera tampering detection from another detection mode.
How to Configure Passing Detection
The detection line for passing moving ob jects is determined by setting the passing direction and object decision 
point.
In the video display area, click the start point of the detection line. ▼
Click another location.
The passing detection line will be set between the start point and next point you clicked.
▼
To configure a polygonal detection line,  click the vertices of the line in order.
Contours of Moving Object Detected as Tampering
1Follow the steps below to use the video display area to configure the passing detection line.
Detection line 
						

							Admin Tools
6
225
You can configure a polygonal detection line with a maximum of 32 vertices.
▼
Click any of the set vertices.
The detection line is determined.
Note
 Even after configuring a detection line, you can drag each vertex  to change the shape of the detection line and the lines between 
vertices to move the entire detection line.
 Click [Clear detection line] to delete a detection line.
If a moving object crosses the detection line in the se lected direction, it will be detected as ‘passed’.
A preview display shows the selected  passing direction on the detection line in the video display area.
If the selected decision point crosses the det ection line, it will be detected as ‘passed’.
The decision point is indicated by a cross  on the detection frame of the moving object.
Set the size ratio of moving objects for the entire screen.
If the moving object exceeds the set value for [Object  Size (%)], it will be targeted for passing detection.
When the setting values or slider is  changed, an indicator frame representing the object size is displayed for one 
second in the center of the video display area allowing y ou to check the size ratio while specifying the setting.
Note
A ratio of up to 30% can be set in [Object Size (%)] for passing detection.
2In [Passing Direction], select the direction fo r moving objects to pass the detection line.
3In [Decision Point], select the point of a moving object that will be used for triggering passing detection when the 
moving object crosses a detection line.
4Configure the size of the moving object needed for triggering detection in [Object  Size (%)].
Detection line
Passing direction (both direction)
Detection FrameDetection Frame
Decision point (bottom center)
Detection line
Object Size Indicator 
						

							226
Detection Status for Passing Detection
All moving objects detected are shown with white contour lines.
When the [Decision Point] of a moving object that exceed s the [Object Size (%)] setting crosses a detection line in 
the direction specified in [Passing Di rection], The countour line changes to the  same color as the detection line, and 
“detected” mode is triggered.
A passing detection event notification  only occurs when the decision line is crossed. Take care in setting the 
operation to be performed when an event occurs.
 How to Configure Intrusion Detection
Set the area you want to detect intrusions.
The decision point is indicated by a cross  on the detection frame of the moving object.
Set the size ratio of moving objects for the entire screen.
When the setting values or slider is  changed, an indicator frame representing the object size is displayed for one 
second in the center of the video display area allowing y ou to check the size ratio while specifying the setting.
Important
Perform a detection test after configuring passing detection to make sure the detection frame of a moving object continues to b e 
displayed.
1Use the video display area to configure the area wher e you would like to detect intruding objects (P. 219).
2Configure [Duration (Sec)] for the time required for an object to  enter a detection area, and be detected as an 
intrusion.
3In [Decision Point], select the point of a moving object that  will be used for triggering intrusion detection when the 
moving object enters a detection area.
4Configure the size of the moving object needed to trigger detection in [Object Size (%)].
Detection Frame
Decision point (bottom center) 
						

							Admin Tools
6
227
Detection Status for Intrusion Detection
All moving objects detected are shown with contour lines.
When [Decision Point] of a moving object larger than [O bject Size (%)] enters a detection area and exceeds 
[Duration (Sec)], its contour lines take on the same color as  the detection area, indicating that “detected” mode has 
been triggered.
Configure Operations for Tri ggered Detection ([Event] Tab)
Set operations to be performed upon detection of changes in a subject.
This will also explain the [Event] tab in [Auto Tracking].
(1)Specify Operation Timing (Multiple  Selections Possible)
[ON Event Operation]
When selected, the operations set in (3) are  performed when “detected” mode is triggered.
[OFF Event Operation]
When selected, the operations set in (3) are performed when “detected” mode ends.
Important
After the Triggered Detection is set, please confirm that the s ystem continues to show contour lines of the Detected Moving 
Object.
Object  Size Indicator
Detection Area
Contour Lines of Detected Moving Object
Video Detection Auto Tracking R11R10
(1)
(3)
(4)
(2)
(3)
(4)
(5)
(6)
(5)
(6) 
						

							228
[Detected mode Operation]
When selected, the operations set in (3) are performed while “detected” mode is active.
(2) [Action During  Auto Tracking] 
When selected, the operations set in (3) are performe d while the moving object is automatically tracked.
(3) Specify Event Operation (Multiple  Selections Possible)
[E-mail Notification]
When selected, e-mail notification is sent  according to the timing set in (1) or (2). [Video Record] > [E-mail Notification] 
in the Setting Page must be set in advance (P. 102).
[Video Record]
When selected, video recording begins according to the timing  specified in (1) or (2). [Video Record] > [Upload] or 
[Memory Card] > [Video Record Setting] in the  Setting Page must be set in advance (P. 96).
(4) Specify Audio Playback Timing 
[Audio Playback at ON Event]
When selected, the sound clip specified in (5) is played back when “detected” mode is triggered.
[Audio Playback at OFF Event]
When selected, the sound clip specified in (5 ) is played back when “detected” mode ends.
(5) Sound Clip  Settings 
[ S ound Clip Name]
Select the sound clip to be played b ack. You must register the sound clip wit h [Video and Audio] > [Audio Settings] > 
[Sound Clip Upload] (P. 88) in  the Setting Page in advance.
[Volume]
Set the volume for the sound clip.
(6) External Device Output Operations  [External Device Output for ON Event]
Select this to start or pause output to an external device  when the “detected” mode is triggered, and to select the 
output destination (output 1 or 2)  and operation (active or inactive).
[External Device Output for OFF Event]
When “detected” mode ends, select whether or not  to begin output to an external device or pause, 
and select the output destination (output 1  or 2) and operation (active or inactive.
Reduce Effects of Lighting Change (Detections Settings)
The Intelligent Function may not work when  the entire screen is exposed to sudden changes in brightness, for example, 
when indoor lights are turned on or off. Changi ng the detection settings may reduce this effect.
The settings are saved and the Intelligent Function restarts.
R11R10
R11M 641M741
R11M 641M741
R11M 641M741
1Click [Detection  Settings].
2Select [Reduce effects of lighting change].
3Click [Save settings]. 
						

							Admin Tools
6
229
Context Menu
Right-click on the video detection setting screen to display a menu that allows you to use the following functions. 
Unavailable functions will be gr ayed-out when you right-click.
Note
If you right-click while using auto tracking, the context menu will appear but none of the functions will be available.
[Copy detection area/line]
Copy the detection area/line of the select ed detection setting to the clipboard.
[Paste detection area/line]
Paste the copied detection area/line from the clipboard to  the detection setting being configured. Paste cannot be used 
with camera tampering detection.
Pasting a detection line is possible only when th e source and the target both set passing detection.
[Clear detection area/line]
Delete the detection area/line of the se lected detection setting. The camera tampering de tection area cannot be deleted.
[Copy detection criteria settings]
Copy the detection criteria of the selected detection setting to the clipboard.
[Paste detection criteria settings]
Paste the copied detection criteria from the clipboard to th e detection setting being configured. Pasting is possible only if 
the source and the target are the same detection type.
[Copy event settings]
Copy the event setting of the selected  detection setting to the clipboard.
[Paste event settings]
Paste the copied event setting from the clipbo ard to the detection setting being configured.
Important
 It takes several seconds for the Intelligent Function to  restart. No detection is performed while restarting.
 Settings in [Reduce effects of lighting change] may not wo rk depending on the operating environment. Sudden changes in 
brightness that persist may also have the  same effect. Perform a detection test to check whether settings work correctly. 
						

							230
For Auto Tracking, set the detection area for moving objects while checking the video on the computer screen. The camera 
is controlled so that the detected moving object appears near the center of the video display area. You can also set which 
operations (such as e-mail notification, recording video, or playing audio from  the speaker connected to the camera) are 
carried out when detection occurs.
Set Auto Tracking
Use the following steps to set Auto Tracking.
For details on how to adjust presets, please refer to “Register Presets” (P. 170).
If you select [Specify the initial camera position], the ca mera angle will be moved to the selected preset position. 
The camera angle will also be moved to the selected preset position after Auto Tracking ends.
Note
You can select presets that meet the following conditions. – Presets configured within the view restrictions.
– Presets with [Show in viewers] selected in the [Preset Registration] tab (P. 171).
– Presets with pan, tilt and zoom setting values (no empty  entries) configured in the [Preset Registration] tab (P. 171).
Intelligent Function Setting Tool 
- Auto Tracking -R11R10
1Obtain camera control privileges  to set Auto Tracking. (P. 158)
2Select [Specify the initial camera position] in [Camera Position  Settings], then select a preset.
Important
It is recommended that you configure preset camera angles in ad vance, so the camera will move to the preset position when auto 
tracking starts or ends.