Canon Lv-7265, Lv-7260, Lv-x7 Multimedia Projector Users Manual

12
2. Installation and Connections
❶
 Setting Up the Screen and the Projector
Selecting a Location (LV-7265)
The further your projector is from the screen or wall, the larger the image. The minimum size the image can be 
is approximately 25" measured diagonally when the projector is roughly 1.1 m (3.7’) from the wall or screen. The 
largest the image can be is 300" when the projector is about 8.8 m (29.1’) from the wall or screen. Use the drawing 
below as a guide.
200"
128"190"...

13
2. Installation and Connections
Selecting a Location (LV-7260/LV-X7)
The further your projector is from the screen or wall, the larger the image. The minimum size the image can be 
is approximately 25" measured diagonally when the projector is roughly 1.1 m (3.7’) from the wall or screen. The 
largest the image can be is 300" when the projector is about 8.8 m (29.1’) from the wall or screen. Use the drawing 
below as a guide.
NOTE:
This projector can be hung from the ceiling (Ceiling mounted)...

14
2. Installation and Connections
WAR N I N G
•  Installing your projector on the ceiling must be done 
by a qualified technician. Contact your dealer for 
more information.
•  Do not attempt to install the projector yourself.
•  Only use your projector on a solid, level surface. If 
the projector falls to the ground, you can be injured 
and the projector severely damaged.
•  Do not use the projector where temperatures vary 
greatly. The projector must be used at temperatures 
between 41˚F (5˚C) and...

15
2. Installation and Connections
❷
 Making Connections
NOTE: When using with a notebook PC, be sure to connect the projector and notebook PC while the projector is in standby 
mode and before turning on the power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on unless connected to the projector before being powered 
up.
*  If the screen goes blank while using your remote control, it may be the result of the computers screen-saver or power man-
agement software....

16
2. Installation and Connections
Using Two Analog COMPUTER Inputs Simultaneously (LV-7265)
If you need to use two analog inputs simultaneously, connect a VGA cable as shown below.
AUDIO INAUDIO OUTS-VIDEOIN
VIDEO
INL
AUDIO INRSERVICE PORTANALOG IN-1
DIGITAL IN /
ANALOG IN-2
DIGITAL IN /
ANALOG IN-2ANALOG IN-1
NOTE: When the DVI to VGA adapter is not to be used for an extended period of time, remove it from the projector. Failure to do 
so may cause damage to the connector of the projector.
IBM PC or...

17
2. Installation and Connections
When Viewing a DVI Digital Signal (LV-7265)
To project a DVI digital signal, be sure to connect the PC and the projector using a DVI digital cable (not supplied) 
before turning on your PC or projector. Turn on the projector fi rst and select Computer 2 (Digital) from the source 
menu before turning on your PC.
Failure to do so may not activate the digital output of the graphics card resulting in no picture being displayed. 
Should this happen, restart your PC.
Do not...

18
2. Installation and Connections
Connecting Your PC or Macintosh Computer (LV-7260/LV-X7)
NOTE: The ANALOG IN connector supports Plug & Play (DDC2).
S-VIDEOIN
VIDEO
INL
AUDIO INRSERVICE PORT
ANALOG INANALOG IN AUDIO IN 
PHONE
PHONE
VGA cable (supplied)To mini D -Sub 15-pin connector on the projector. 
It is recommended that you use a commercially 
available distribution amplifier if connecting a 
signal cable longer than the supplied one.
IBM PC or Compatibles (Desktop type)
or Macintosh (Desktop...

19
2. Installation and Connections
Connecting an External Monitor
AUDIO IN
AUDIO OUTS-VIDEOIN
VIDEO
INL
AUDIO INRSERVICE PORT
ANALOG IN-1
DIGITAL IN /
ANALOG IN-2
ANALOG IN 1
AUDIO IN 
S-V IDEOIN
VIDEO
INL
AUDIO INRSERVICE PORT
ANALOG IN
You can connect a separate, external monitor to your projector to simultaneously view on a monitor the RGB ana-
log image youre projecting.
NOTE: Daisy chain connection is not possible.
NOTE:
•   The signal from the DIGITAL IN/ANALOG IN-2 connector cannot be output from...

20
AUDIO IN
AUDIO OUTS-VIDEOIN
VIDEO
INL
AUDIO INRSERVICE PORT
ANALOG IN-1
DIGITAL IN /
ANALOG IN-2
AUDIO INLR
AUDIO OUT
LR
Component
YCbCr
ANALOG IN-1AUDIO IN 
2. Installation and Connections
A component signal will be automatically displayed. If not, from the menu, select [Setup] 
→ [Input signal select] 
→ 
[Computer 1] or [Computer 2 (Analog)] ([Computer] on LV-7260/LV-X7) 
→ [COMPONENT].
NOTE: Refer to your DVD players owners manual for more information about your DVD players video output...

21
2. Installation and Connections
AUDIO INLRAUDIO OUTLRVIDEO OUTS-VIDEO VIDEO
AUDIO IN
AUDIO OUTS-VIDEOIN
VIDEO
INL
AUDIO INRSERVICE PORT
ANALOG IN-1
DIGITAL IN /
ANALOG IN-2
VIDEO INAUDIO IN
S-VIDEO IN
Connecting Your VCR or Laser Disc Player
S-Video cable (not supplied)
Video cable (not supplied)
VCR/ Laser disc player
Audio equipment
Audio cable (not supplied)
NOTE: The AUDIO IN L/MONO and R jacks (RCA) are shared between the Video and S-Video inputs.
NOTE: Refer to your VCR or laser disc player...