Canon large format printer imagePROGRAF iPF6400 User Manual

To use the ARP and PING commands, you will need to know the printer's MAC address. You can confirm the MAC
address on the Control Panel.1
Check the printer's MAC address.
You can confirm the MAC address on the Control Panel as follows:
1.
  On the  Tab Selection screen  of the Control Panel, press  ◀ or  ▶ to
select the Settings/Adj. tab ( 
).
2.
Press the  OK button.
The  Set./Adj. Menu  is displayed.
3.
Press ▲ or  ▼ to select  Interface Setup , and then press the  OK button.
4.
Press  ▲ or  ▼...

Configuring TCP/IPv6 Network Settings
Configuring TCP/IPv6 Network Settings
When printing in a TCP/IPv6 network, you must configure the TCP/IPv6 settings on the Control Panel.
Follow the steps below to configure the TCP/IPv6 network settings.
1
 
On the  Tab Selection screen  of the Control Panel, press  ◀ or  ▶ to se-
lect the Settings/Adj. tab ( 
).
Note
•If the Tab Selection screen is not displayed, press the Menu button.2
Press the  OK button.
The  Set./Adj. Menu  is displayed.
3
Press ▲ or  ▼ to...

3
Click the Port tab to display the  Port sheet.
4
Click  Add Port  to display the  Printer Ports dialog box.
5
In the Available Port  list, select Standard TCP/IP Port .
6
Click New Port .
After the wizard starts, a window is displayed for the  Welcome to the Add Standard TCP/IP Printer Port Wiz-
ard .
7
Click  Next.
8
In Printer Name or IP Address , enter the printer's IP address. If the DNS is configured, you can also enter the
DNS Domain Name.
9
Follow the instructions on the screen to add a...

6
Refer to the TCP/IP Settings Items table to complete the settings.
TCP/IP Settings ItemsItemDetailsDefault SettingUse DHCPActivate this setting to use DHCP for configuring the IP address.OffUse BOOTPActivate this setting to use BOOTP for configuring the IP address.OffUse RARPActivate this setting to use RARP for configuring the IP address.OffEnable DNS DynamicUpdateActivate this setting to perform DNS server registration automatically.OffUse Zeroconf FunctionActivate this setting to use Bonjour.OnIP...

When using an IPv6 IP address
1
Start the web browser and enter the following URL in the Location (or Address  ) box to display the RemoteUI
page.
http:// printer IP address or name /
Example: http://xxx.xxx.xxx.xxx/
2
Select  Administrator Mode  and click Logon.
3
If a password has been set on the printer, enter the password.
4
Click Network  in the Device Manager  menu at left to display the  Network page.
5
Click Edit in the upper-right corner of the  TCP/IPv6 group to display the  Edit TCP/IPv6...

NetWare Settings
NetWare Settings
Configuring NetWare Network Settings ...................................................................................................................... 686
Specifying the Printer's Frame Type ............................................................................................................................ 686
Specifying NetWare Print Services...

Important•Before specifying the frame type, make sure the printer is on and connected to the network.
Note
•You can specify the frame type by using RemoteUI if the printer's IP address is configured.•For instructions on installing imagePROGRAF Device Setup Utility, see "Installing imagePROGRAF Device Setup Utility."→P.703.
Specifying the frame type using imagePROGRAF Device Setup Utility
1
 
Start imagePROGRAF Device Setup Utility.
2
In the list of printers, select the printer to configure....

5
 
Select the  IPv4 tab. In  IP Address , enter the IP ad-
dress assigned to the printer, and then enter the subnet mask in  Subnet Mask  and the default gateway in
Gateway Address .
Important•You must specify the IP address here to be able to configure NetWare protocol settings using RemoteUI.6
Click Set.
7
Click  OK after the  Confirmation  message is displayed.
8
Exit imagePROGRAF Device Setup Utility.
Specifying the frame type using the printer Control Panel
1
 
On the  Tab Selection screen  of the...

3
Press ▲ or  ▼ to select  Interface Setup , and then press the  OK button.
4
Press  ▲ or  ▼ to select  NetWare, and then press the  OK button.
5
Press  ▲ or  ▼ to select  NetWare, and then press the  OK button.
6
Press  ▲ or  ▼ to select  On, and then press the  OK button.
The display reverts to the  NetWare menu.
7
Press ▲ or  ▼ to select  Frame Type , and then press the  OK button.
8
Press  ▲ or  ▼ to select the frame type to use, and then press the  OK button.
The display reverts to the  NetWare...

Note
•In NetWare 5.1 or 6.0, NDPS may also be used as the print service. If you use NDPS, use the Novell printer gateway includedwith NetWare. For details on configuring NDPS, refer to the NetWare documentation.•
NDS (Novell Directory Service) and bindery
NDS and bindery are both supported. Use the mode that is compatible with your network environment.
•
Queue server mode and remote printer mode
Queue server mode and remote printer mode are both supported.
•
Queue server mode
When using queue server...