Canon Imageprograf Ipf815 User Guide

1.
Lift the Holder Stopper lever (a) from the shaft side to unlock it. Holding the Holder Stopper at the position indica-
ted (b), remove it from the Roll Holder. 2.
When 
using a 3-inch paper core, align the tips (a) of 3-Inch Paper Core Attachment #1 with the holes (b) of the Roll
Holder and insert it firmly. Handling Paper 
> Handling rolls >
iPF815
Attaching the Roll Holder to Rolls 7
625
 

3.
With the  edge  of  the  roll  paper  facing  forward  as  shown,  insert  the  Roll  Holder  from  the  right  of  the  roll.  Insert  it
firmly until the roll touches the flange (a) of the Roll Holder. Important
• When 
loading  a  roll,  be  careful  to  avoid  hitting  the  printer  hard  with  the  roll.  This  may  damage  the
Roll Holder.
4. Insert the attachments for the roll paper core on the Holder Stopper.
Align the tips (a) of the attachment with the holes (b) of the Holder Stopper and...

•
2-Inch Paper Core Attachment 5.
Insert the  Holder  Stopper  from  the  left  in  the  Roll  Holder  as  shown.  Holding  it  at  the  position  shown  (b),  push  it
firmly in until the flange (a) of the Holder Stopper touches the roll. Lock the Holder Stopper lever (c) by pushing it
down toward the shaft side. Handling Paper 
> Handling rolls >
iPF815
Attaching the Roll Holder to Rolls 7
627
 

Loading Rolls in the Printer
Follow these steps to load rolls in the printer. Note
• Remove any loaded paper that will not be used.
• Rolls  (See "Removing the Roll from the Printer .") →P.634
• Sheet  (See "Removing Sheets .") →P.656
• If the Platen is dirty, clean inside the Top Cover.   (See "Cleaning Inside the Top Cover.") →P.837
• After 
pressing  the  Load/Eject  button,  you  can  refer  to  instructions  on  the  Display  Screen  as  you  load  the
paper.  (See...

3.
Holding  the Roll Holder so that the side with the white gear faces the side of the Roll Holder Slot with a white gear,
load the Roll Holder shaft (a) into the grooves (b) on both ends of the Roll Holder Slot. Caution
• Be 
careful not to pinch your fingers between the Roll Holder shaft (a) and the guide grooves (b) when
loading rolls. Note
• For 
instructions  on  attaching  the  Roll  Holder  to  rolls,  see  "Attaching  the  Roll  Holder  to  Rolls."→P.623 Handling Paper 
> Handling rolls...

4.
Pull out  the  roll  paper  evenly  on  both  ends.  Using  both  hands,  insert  the  roll  paper  in  the  Paper  Feed  Slot  and  ad-
vance it until the buzzer sounds. Important
• Be 
careful not to soil the printing surface of roll paper as you insert it in the slot. This may affect the
printing  quality.  We  recommend  wearing  clean  cloth  gloves  when  handling  rolls  to  protect  the  print-ing surface.
• If the paper is wrinkled or warped, straighten it out before loading it.
• Load the...

5.
Lower the Ejection Guide. 6.
Close the Top Cover. 7.
Press the OK button.
The printer will now advance the paper.
After you load a roll, the printer automatically shows a menu for selection of the type of paper on the Display Screen.
At this point, specify the type of paper.   (See "Selecting the Paper Type (Roll) .") →P.632
Selecting the Paper Source
When advancing paper, press the  Feeder Selection button and select the source.
You can determine the selected source by checking which lamp is...

Note
• If a  sheet  is  loaded  when  you  change  the  paper  source  to  a  roll,  " Eject  sheet?"  is  displayed.  Press  the  OK
button and remove the sheet.
• You cannot switch the paper source in the following situations:
• When the Message lamp is flashing
Check  the  message  on  the  Display  Screen  and  take  action  as  necessary.  (See  " Error  Messag-
es →P.891
.")
• When the Data lamp is flashing
Select the paper source after printing is finished.
• When a printer menu...

2.
Press ▲ or ▼ to select  Media Menu, and then press the  ▶ button.
3. Press ▲ or ▼ to select  Roll Media Type, and then press the  ▶ button.
4. Press ▲ or ▼ to select the type of paper loaded in the printer, and then press the  OK button.Note
• For details on types of paper, see the Paper Reference Guide.   (See "Types of Paper.") →P.617
 By
default, Plain Paper is selected.
• If you move the Release Lever, the setting automatically reverts to the previously selected paper.
• Be 
sure to select...

2.
Press ▲ or ▼ to select  Media Menu, and then press the  ▶ button.
3. Press ▲ or ▼ to select  Roll Length Set, and then press the  ▶ button.
4. Press  ▲ or ▼ to select the length of paper loaded in the printer, and then press the  OK button.
Specify the roll length as follows.
1. Press  ◀ or ▶ to move the cursor (_) to each field for entering numbers.
2. Press the ▲  or ▼ button to enter the value.
3. Repeat steps 1 and 2 to finish entering the value, and then press the  OK button.
5. Press the Online...