Canon I Sensys Lbp6230dw User Guide

Click [Close].
3Click [OK].
4
>å>Ý>Ì>Û>Ì>Þ>à>Ü
 

0JFC -021
Configuring the Machine for Your Network Environment
The size and  configuration of a network varies  depending on  the  purpose of the  network. This machine has been designed to  be
compatible  with as many network configurations  as possible,  and  it is  equipped with a variety  of network technologies. Consult your
network administrator and  set a configuration to  suit your network environment.
>å>Þ>Ì>Û>Ì>Þ>à>Ü
 

0JFC -053
Configuring Ethernet Settings
Ethernet is  a standard for  communicating data in a LAN. You  can set the  communication mode (Half Duplex/Full  Duplex)  and  the
Ethernet type (10BASE-T/100BASE-TX). The factory default  setting, the  communication mode and  type of Ethernet are  automatically
detected.  Usually, the  Ethernet settings can be used as is,  but use the  following  procedure to  manually specify  the  settings as necessary.
Start  the Remote UI  and  log  on in System Manager Mode....

[Auto  Detect]
Clear the  check  box to  configure the  Ethernet settings manually.  Select the  check  box to  detect the  Ethernet settings
automatically.
[Communication Mode]
Select the  Ethernet communication mode.[Half Duplex] Alternately  sends and  receives communication data. Select this when the  machine is  connected to  a
networking device using half  duplex.
[Full Duplex] Simultaneously sends and  receives communication data. Use  this setting for  most environments.
[Ethernet  Type]
Select...

0JFC -022
Changing the Maximum Transmission Unit
In most Ethernet networks, the  maximum  size of a packet  that  can be sent is  1500  bytes.  A packet  refers to  a small chunk  of data. The
original  data is  divided into packets  before being sent. The maximum  transmission unit  (MTU)  may  vary on  each network. Change  t he
settings of the  machine as necessary. For more information, contact your network administrator.
Start  the Remote UI  and  log  on in System Manager Mode.  Starting the Remote...

Turn  OFF  the  machine, wait  for  at least  10 seconds,  and  turn  it back ON.
LINKS
Configuring  Ethernet Settings
Setting a Wait Time for Connecting to a Network
>å>â>Ì>Û>Ì>Þ>à>Ü
 

0JFC -023
Setting a Wait Time for Connecting to a Network
When  a network is  designed with multiple switching hubs  or bridges in order to  provide redundant  connectivity,  it must have a
mechanism to  prevent  packets  from looping.  One  effective solution  is  to  define the  role of each switch  port. However, communication
may  still be disrupted  for  a certain time  immediately  after you change the  network, for  example  by adding a new device. If  this type of
problem occurs, set a wait  time...

LINKS
Configuring  Ethernet Settings
Changing the Maximum Transmission  Unit
>å>ä>Ì>Û>Ì>Þ>à>Ü
 

0JFC -024
Configuring DNS
DNS (Domain  Name System) provides a service for  name resolution that  associates  a host  (or domain)  name with an  IP  address.
Configure the  DNS, mDNS,  or DHCP option settings as necessary  according to  your network. Note that  the  procedures for  configuring
DNS are  different  for  IPv4  and  IPv6.
Start  the Remote UI  and  log  on in System Manager Mode.  Starting the Remote UI
Click [Settings/Registration].
Click [Network Settings]  [TCP/IP  Settings].
Configure...

[DNS  Settings][Primary DNS  Server Address]
Enter the  IP  address of the  DNS server.
[Secondary DNS  Server Address]
When  there is  a secondary DNS server, enter its IP  address.
[Host Name]
Enter up  to  47 alphanumeric  characters  for  the  host  name of the  machine that  is  to  be registered with the  DNS server.
[Domain Name]
Enter up  to  47 alphanumeric  characters  for  the  name of the  domain  the  machine belongs to  (such as "example.com").
[DNS  Dynamic  Update]
Select the...