Canon Eos Rebel T6s 760d Instruction Manual

W-37
Selecting the Connection Destination
4Select the images to send.
Select images on the camera sending 
the images (p.W-38).
 Do not operate the camera receiving 
the images.
Note that GPS information is not displayed on the camera’s playback screen 
even if GPS information is appended to the received image. Shooting 
locations can be viewed on a virtual map, using Map Utility (EOS software).
 The connection settings are saved/ registered with the nickname of the 
camera to which a connection was...

W-38
Select and send images individually.
1Select an image to send.
Turn the < 5> dial to select an image 
to send, then press < 0>.
 By pressing the < I> button, you 
can switch to the index display and 
select an image.
2Select [Send img shown].
 To select a size at which to send the 
image, select [ Resize image] and 
press < 0>.
 Press the < Y> < Z> keys to select 
[Send img shown ], then press .
 The transfer progress screen will 
appear. When the transfer is 
complete, the screen for step 1...

W-39
Sending Images
Select multiple images and send them at once.
1Press .
2Select [Send selected].
To select a size at which to send the 
images, select [ Resize image] and 
press < 0>.
 Press the < Y> < Z> keys to select 
[Send selected ], then press .
3Select the images to send.
 Turn the < 5> dial to select an image 
to send, then add [ X]. Press  to 
add or remove [X].
 By pressing the < I> button, you 
can switch to the three-image display 
and select an image.
 After selecting the images to...

W-40
Sending Images
4Reduce the image size.
Set it if necessary.
 On the next screen, press the < W> 
< X > keys to select an image size, 
then press < 0>.
5Send the images.
 Press the < W> < X> keys to select 
[Send ], then press < 0> to send the 
images.
 The transfer progress screen will 
appear. When the transfer is 
complete, the screen for step 1 will 
reappear.
 To send another image, repeat steps 
1 to 5.
6Terminate the connection.
Press the < M> button to display 
the confirmation dialog....

W-41
Sending Images
While connected, a picture cannot be taken even if the camera’s shutter 
button is pressed. When you want  to terminate the connection to shoot 
or perform other operations, press the < M> button, then terminate 
the connection on the displayed screen. To terminate the connection 
during image transfer, select [ Cancel] on the camera, then terminate the 
connection.
 When sending a large number of images or large files (total size), make 
sure that the battery is adequately charged...

W-42
The camera can reconnect to another camera for which connection settings have been registered.
1Select [Wi-Fi function].
Under the [5 1] tab, set [Wi-Fi/NFC] 
to [ Enable], then select [ Wi-Fi 
function ].
2Select [z].
 Select [ z] (Transfer imgs between 
cameras) and press < 0>.
3Establish a connection.
 Select [ Connect ] and press < 0>.

On the confirmation dialog, select [OK ].Perform the reconnection procedure 
on the target camera as well.

The images on the card are displayed 
and the...

W-43
5
Easy Connection toConnect Station
Connect Station (sold separately) is a device that allows 
you to import captured st ill photos and movies for 
viewing on your TV set, smartphone, etc., or sharing 
them over a network.
You can easily save still photos and movies to Connect 
Station by holding this camera close to Connect Station. 

W-44
This section explains how to connect the camera and Connect Station 
(sold separately) via a wireless LAN. To save images in other ways, 
refer to the Connect Station instruction manual.
 Set up the camera to allow use of its NFC function in advance (p.W-
20).
1Set up the camera to allow use of 
its NFC function 
(p.W-20).
2Hold the camera close to Connect 
Station.
Turn on the camera and Connect 
Station, then hold the camera’s  p 
mark close to the Connect Station’s 
NFC connect point.
 A...

W-45
Saving Images
Do not drop the camera on Connect Station or touch the camera to it with 
too much force. Doing so may damage Connect Station’s internal hard disk.
Since the camera may not be recognized readily, hold it carefully close to 
Connect Station while changing the camera’s position or angle.
 Just holding the camera close to Connect Station may not establish a 
connection. In such a case, gent ly touch Connect Station with the 
camera.
 A connection cannot be established  via the NFC...

W-46
MEMO