Canon Eos Rebel T6s 760d Instruction Manual

							W-37
Selecting the Connection Destination
4Select the images to send.
Select images on the camera sending 
the images (p.W-38).
 Do not operate the camera receiving 
the images.
Note that GPS information is not displayed on the camera’s playback screen 
even if GPS information is appended to the received image. Shooting 
locations can be viewed on a virtual map, using Map Utility (EOS software).
 The connection settings are saved/ registered with the nickname of the 
camera to which a connection was established.
 While connected, auto power off does not function. 
						

							W-38
Select and send images individually.
1Select an image to send.
Turn the < 5> dial to select an image 
to send, then press < 0>.
 By pressing the < I> button, you 
can switch to the index display and 
select an image.
2Select [Send img shown].
 To select a size at which to send the 
image, select [ Resize image] and 
press < 0>.
 Press the < Y> < Z> keys to select 
[Send img shown ], then press .
 The transfer progress screen will 
appear. When the transfer is 
complete, the screen for step 1 will 
reappear.
 To send another image, repeat steps 
1 and 2.
3Terminate the connection.
Press the < M> button to display 
the confirmation dialog. Press the 
< Z > key to select [ OK], then press 
< 0 > to terminate the connection.
 The [ Wi-Fi function ] screen will 
reappear.
Sending Images
Sending Images Individually 
						

							W-39
Sending Images
Select multiple images and send them at once.
1Press .
2Select [Send selected].
To select a size at which to send the 
images, select [ Resize image] and 
press < 0>.
 Press the < Y> < Z> keys to select 
[Send selected ], then press .
3Select the images to send.
 Turn the < 5> dial to select an image 
to send, then add [ X]. Press  to 
add or remove [X].
 By pressing the < I> button, you 
can switch to the three-image display 
and select an image.
 After selecting the images to send, 
press the < Q> button.
Sending Multiple Images 
						

							W-40
Sending Images
4Reduce the image size.
Set it if necessary.
 On the next screen, press the < W> 
< X > keys to select an image size, 
then press < 0>.
5Send the images.
 Press the < W> < X> keys to select 
[Send ], then press < 0> to send the 
images.
 The transfer progress screen will 
appear. When the transfer is 
complete, the screen for step 1 will 
reappear.
 To send another image, repeat steps 
1 to 5.
6Terminate the connection.
Press the < M> button to display 
the confirmation dialog. Press the 
< Z > key to select [ OK], then press 
< 0 > to terminate the connection.
 The [ Wi-Fi function ] screen will 
reappear. 
						

							W-41
Sending Images
While connected, a picture cannot be taken even if the camera’s shutter 
button is pressed. When you want  to terminate the connection to shoot 
or perform other operations, press the < M> button, then terminate 
the connection on the displayed screen. To terminate the connection 
during image transfer, select [ Cancel] on the camera, then terminate the 
connection.
 When sending a large number of images or large files (total size), make 
sure that the battery is adequately charged so it does not run out during 
the process.
 Depending on the functionality of the target camera, the movie files will 
be converted when they are sent. Therefore, transfer may take longer 
than usual.
RAW images cannot be sent.
 You can select up to 50 files at a time.
 When you reduce the image size, all images to be sent at the same time 
are resized except for movies and for images that are already smaller 
than the selected image size.
 [Resize:S2 ] and [Resize:S3 ] are enabled only for still photos shot with 
the EOS REBEL T6S/EOS 760D. Images shot with other cameras are 
sent without resizing.
 The file size (total size) is based  on the file sizes before resizing the 
images.
 You can cancel the image transfer by selecting [ Cancel] during the 
transfer. When [ Cancel] is selected on the camera sending the images, 
the image selection screen will reappear. When [ Cancel] is selected on 
the camera receiving the images, the connection will be terminated. 
						

							W-42
The camera can reconnect to another camera for which connection settings have been registered.
1Select [Wi-Fi function].
Under the [5 1] tab, set [Wi-Fi/NFC] 
to [ Enable], then select [ Wi-Fi 
function ].
2Select [z].
 Select [ z] (Transfer imgs between 
cameras) and press < 0>.
3Establish a connection.
 Select [ Connect ] and press < 0>.

On the confirmation dialog, select [OK ].Perform the reconnection procedure 
on the target camera as well.

The images on the card are displayed 
and the images to send can be selected.
 When settings for multiple connecti on destinations are registered, 
select [Choose set. ], select the connection destination, then 
connect to the destination.
 By default, settings are named after the nickname of the camera that 
was connected to.
Reconnecting 
						

							W-43
5
Easy Connection toConnect Station
Connect Station (sold separately) is a device that allows 
you to import captured st ill photos and movies for 
viewing on your TV set, smartphone, etc., or sharing 
them over a network.
You can easily save still photos and movies to Connect 
Station by holding this camera close to Connect Station. 
						

							W-44
This section explains how to connect the camera and Connect Station 
(sold separately) via a wireless LAN. To save images in other ways, 
refer to the Connect Station instruction manual.
 Set up the camera to allow use of its NFC function in advance (p.W-
20).
1Set up the camera to allow use of 
its NFC function 
(p.W-20).
2Hold the camera close to Connect 
Station.
Turn on the camera and Connect 
Station, then hold the camera’s  p 
mark close to the Connect Station’s 
NFC connect point.
 A message indicati ng the connection 
is displayed on the camera’s LCD 
monitor.
 When a connection is established, 
Connect Station checks the images 
on the memory card, then saves only 
the unsaved images.
3Terminate the connection.
After images are saved, the screen 
on the left will appear on the camera’s 
LCD monitor. Press  to 
terminate the connection.
Saving Images
NFC connect point 
						

							W-45
Saving Images
Do not drop the camera on Connect Station or touch the camera to it with 
too much force. Doing so may damage Connect Station’s internal hard disk.
Since the camera may not be recognized readily, hold it carefully close to 
Connect Station while changing the camera’s position or angle.
 Just holding the camera close to Connect Station may not establish a 
connection. In such a case, gent ly touch Connect Station with the 
camera.
 A connection cannot be established  via the NFC function while shooting 
with the camera, when the power switch is set to < k>, when there is no 
card, or when the LCD monitor is closed with the screen facing inward.
 When holding the camera close to Connect Station, do not leave 
anything between the camera and Connect Station. In addition, when a 
case is attached to the camera, communication may not be possible via 
NFC function.
 When Battery Grip BG-E18 (sold separately) is attached, a connection 
cannot be established via the NFC function.
 If the camera and Connect Station are moved too far away from each 
other while importing images, import may take time or the connection 
may be terminated.
 If the camera’s battery runs out  during import, the import will stop. 
Charge the battery, then try importing again.
 A connection can be established even when the camera’s power is in the 
auto power off state. However, if a connection cannot be established, 
cancel auto power off, then establish a connection.
 When all images are already imported, import does not start. In such a 
case, select [ OK] to terminate the connection.
 When there are a large number of images on the memory card, it may 
take time to check and save the images. 
						

							W-46
MEMO