Canon Eos Rebel T4i 650d Instruction Manual

191
When you set the power switch to , the [Z 1/Z 2] tab will show 
functions dedicated to movie s hooting. The menu options are as 
follows.
[Z 1] menu  [Z 2] menu
 AF method
The AF methods are the same as  described on pages 153-159. You 
can select [ u+Tracking ], [FlexiZone - Multi ], or [FlexiZone - 
Single ].
  Movie Servo AF
The default setting is [ Enable]. You can focus by pressing the 
shutter button halfway regardless of the setting.
• When [Enable] is set:
• You can shoot a movie while...

192
3 Movie Menu Function Settings
• If you want to hold the focus at a certain point or avoid recording 
the lens operation noise before or during movie shooting, you 
can temporally stop Movie Servo AF by performing one of the 
operations below. When you stop  Movie Servo AF, the AF point 
will turn gray. When you perform the same operation again, 
Movie Servo AF will resume.
• Press the < D> button.
• Tap the [ ] icon on the lower left of the screen.
• If [ 6: Shutter/AE lock button ] is set to [2:...

193
3 Movie Menu Function Settings
 Grid display
With [Grid 1 l] or [ Grid 2 m], you can display grid lines to help 
you level the camera vertically or horizontally.
  Metering timer N
You can change how long the exposure se tting is displayed (AE lock time).
 Movie recording size
You can set the movie recording size (image size and frame rate). 
For details, see pages 181-182.
  Sound recording N
Normally, the built-in microphone will 
record stereo sound. If a commercially-
available microphone...

194
3 Movie Menu Function Settings
[Wind filter ]
When set to [ Enable], it reduces wind noise when there is wind 
outdoors. This feature takes effect only with the built-in 
microphone.
Note that [ Enable] will also reduce low  bass sounds, so set this 
function to [ Disable] when there is no wind. It will record a more 
natural sound than with [ Enable].
[Attenuator ]
Even if you set [ Sound recording ] to [Auto ] or [Manual ] and 
shoot, sound distortion may still result if there is a very loud sound....

195
Movie Shooting Cautions
White  and Red < E> Internal Temperature Warning Icons
  If the camera’s internal temperatu re increases due to prolonged movie 
shooting or under a high ambi ent temperature, a white icon < s> will 
appear. Even if you shoot a movie wh ile this icon is displayed, the 
movie’s image quality will hardly be affected. However, if you shoot still 
photos, the image qualit y of the still photos may deteriorate. It is 
recommended to stop still photo sh ooting for a while and allow...

196
Movie Shooting Cautions
Recording
 If you use a card with a slow  writing speed, a five-level 
indicator may appear on the right of the screen during movie 
shooting. It indicates how  much data has not yet been 
written to the card (remaining ca pacity of the internal buffer 
memory). The slower the card, the faster the indicator will 
climb upward. If the indicator  becomes full, movie shooting 
will stop automatically. If the ca rd has a fast writing speed, 
the indicator will either not app ear...

197
Cautions when [Movie servo AF] is set to [Enable]
Shooting conditions that make focusing difficult
  A fast-moving subject ap proaching or moving away from the camera.
  A subject moving at a close dist ance in front of the camera.
  Also refer to “Shooting co nditions that make focusing difficult” on page 
159.
• Since using Movie Servo  AF will consume battery power, the number of 
possible shots and the po ssible movie shooting time will be reduced.
• During zooming or image magnificatio n, Movie...

COPY  

199
Handy Features
 Disabling the Beeper (p.200)
  Card Reminder (p.200)
  Setting the Image Review Time (p.200)
  Setting the Auto Power-off Time (p.201)
  Adjusting the LCD Monitor Brightness (p.201)
  Creating and Selectin g a Folder (p.202)
  File Numbering Methods (p.204)
  Setting Copyright Information (p.206)
  Auto Rotation of Vertical Images (p.208)
  Checking Camera Settings (p.209)
  Reverting the Camera to the Default Settings (p.210)
  Preventing the LCD Monitor from  Turning Off...

200
You can prevent the beeper from sounding when focus is achieved, 
during self-timer operation, and during touch screen operations.
Under the [z1] tab, select [ Beep], then 
press < 0>. Select [ Disable], then 
press < 0>.
To silence the beeper only during touch 
screen operations, select [ Touch to ].
This setting prevents shooting if there is no card in the camera. Under the [z1] tab, select [ Release 
shutter without card ], then press 
< 0 >. Select [Disable], then press 
< 0 >.
If there is no...