Canon Eos Rebel T1i 500d Instruction Manual

							
171
wPrinting
You can crop the image and print only 
the trimmed portion as if the image was 
recomposed.  Do the trimming right 
before printing.  If you set the trimming 
and then set the print settings, you may 
have to set the trimming again.
1 On the print setting screen, select [Trimming].
2 Set the trimming frame size, position, and aspect ratio.
 The image area within the trimming  frame will be printed. The 
trimming frame’s aspect ra tio can be changed with [
Paper settings].
Changing the trimming frame size
When you press the < u> or < I> button, the size of the 
trimming frame will change. The sm aller the trimming frame, the 
larger the image magnification will be for printing.
Moving the trimming frame
Press the  key to move the frame over  the image vertically or 
horizontally. Move the tri mming frame until it covers  the desired image area.
Rotating the frame
Each time you press the  button, the trimming frame will 
toggle between the vertical and hor izontal orientations. This enables 
you to create a vertical-oriente d print from a horizontal image.
Image tilt correction
By turning the < 6> dial, you can adjust  the image tilt angle up to 
± 10 degrees in 0.5-degree increments. When you adjust the 
image tilt, the < O> icon on the screen will turn blue.
3 Press  to exit the trimming.
XThe print setting  screen will reappear.
  You can check the trimmed image  area on the upper left of the 
print setting screen.
Trimming the Image
Tilt correction  
						

							
wPrinting
172
 Depending on the printer , the trimmed image area  might not be printed 
as you specified.
  The smaller you make the trimming fr ame, the grainier the picture will 
look on the print.
  While trimming the image, look at th e camera’s LCD monitor. If you look 
at the image on a TV sc reen, the trimming frame  might not be displayed 
accurately.
Handling Printer ErrorsIf you resolve a printer error (no in k, no paper, etc.) and select [Continue] to 
resume printing but it doe s not resume, operate the bu ttons on the printer to 
resume printing. For de tails, see the printer’s instruction manual.
Error MessagesIf a problem occurs duri ng printing, an error message will appear on the 
camera’s LCD monitor. Press  to stop printing . After fixing the 
problem, resume prin ting. For details on how to  fix a printing problem, refer 
to the printer’s instruction manual.
Paper Error
Check whether the paper is pr operly loaded in the printer.
Ink Error Check the printer’s ink level,  and check the waste ink tank.
Hardware Error Check for any printer problems ot her than paper and ink problems.
File Error The selected image  cannot be printed via PictBr idge. Images taken with a 
different camera or images  edited with a computer might not be printable.  
						

							
173
You can set the print type, date imprinting, and file No. imprinting. The 
print settings will be applied to al l print-ordered images. (They cannot 
be set individually for each image.)
1Select [Print order].
XUnder the [ 3] tab, select [ Print 
order ], then press < 0>.
2Select [Set up].
  Select [ Set up], then press < 0>.
3Set the option as desired.
  Set the [ Print type ], [Date ], and [ File 
No. ].
  Select the option, then press < 0>. 
Select the setting, then press < 0>.
W Digital Print Order Format (DPOF)
Setting the Printing Options
[Print type][Date][File No.]  
						

							
W Digital Print Order Format (DPOF)
174
4 Exit the setting.
  Press the < 7> button.
X The print order screen will reappear.
  Next, select [ Sel.Image] or [All 
image ] to order the images to be 
printed.
Print type
KStandard Prints one image on one sheet.
LIndexMultiple, thumbnail images ar e printed on one sheet.
K
LBothPrints both the standard and index prints.
Date On
[On ] imprints the recorded  date on the print.
Off
File numberOn[On ] imprints the file No. on the print.
Off
  Even if [ Date] and [ File No. ] are set to [ On], the date or fi le No. might not 
be imprinted depending on the pr int type setting and printer model.
  When printing with DP OF, you must use the ca rd whose print order 
specifications have been set. It will  not work if you just extract images 
from the card and try to print them.
  Certain DPOF-compatible printers an d photofinishers might not be able 
to print the images as you specified.  If this happens with your printer, 
refer to the printer’s inst ruction manual. Or check  with your photofinisher 
about compatibility wh en ordering prints.
  Do not insert into the camera a ca rd whose print order was set by a 
different camera and then try to spec ify a print order. The print order may 
not work or may be overwritten. Also , depending on the image type, the 
print order may not be possible.
  RAW images and movies ca nnot be print ordered.
  With [ Index ] prints, both the [ Date] and [ File No. ] cannot be set to [ On] 
at the same time.  
						

							
175
W Digital Print Order Format (DPOF)
  Sel.Image
Select and order images one by one.
Press the  button to display the 
three-image view. To return to the single-
image display, press the < u> button.
After completing the print order, press 
the < M > button to save the print 
order to the card.
[Standard] [Both]
Press the < V> key to set the number 
of copies to be printed for the displayed 
image.
[Index]
Press the < V> key to checkmark the 
box < X> and the image will be included 
in the index print.
  All image
If you select [ Mark all on card ], one copy of all the images in the 
card will be set for printing. If you select [ Clear all on card], the print 
order will be cleared for all  the images in the card.
Print Ordering
Quantity
Total images selected
Index icon
Check mark
 
If you select “All image” , RAW images and movies  will not be included in 
the print order.
  When using a PictBridge  printer, print no more than 400 images for one 
print order. If you specify more than  this, all the images might not be 
printed.  
						

							
176
With a PictBridge printer, you can easily 
print images with DPOF.
1Preparing to print.
 See page 164. Follow the “Connecting  the Camera to a Printer” 
procedure up to step 5.
2Under the [ 3] tab, select [Print order].
3Select [Print].
  [Print ] will be displayed only if the camera is connected to the 
printer and printing is possible.
4Set the [Paper settings]. (p.166)
  Set the printing effects (p.168) if necessary.
5Select [OK].
W Direct Printing with DPOF
  Before printing, be sure  to set the paper size.
  Certain printers cannot  imprint the file No.
 
If [Bordered] is set, the date might be imprinted on the border, depending on the printer.  Depending on the printer, th e date might look light if it is imprinted on a 
bright background  or on the border.
 Under [ Adjust levels ], [Manual ] cannot be selected.
  If you stopped the printin g and want to resume printing the remaining 
images, select [ Resume]. Note that printing will  not resume if you stop 
the printing and any of the following occurs:
• Before resuming the printing, you  changed the print order or deleted 
print-ordered images.
• When you set the index, you changed the paper setting before resuming the printing.• When you paused the printing, the  card’s remaining capacity was low.
  If a problem occurs during  printing, see page 172.  
						

							
177
By connecting the camera to a computer, you can transfer images from 
the camera’s card by operating the camera. This is called direct image 
transfer. Before connecting the camera to a computer, be sure to install 
the provided software (EOS DIGITAL Solution Disk on CD-
ROM) in the computer.
For instructions to install the pr ovided software, see the separate 
sheet, CD-ROM Guide.
1Set the camera’s power switch to 
.
2Set the shooting mode to any 
mode except < k>.
3Connect the camera to the 
computer.
 Use the interface cable provided with 
the camera.
  When connecting the cable plug to 
the camera’s < q/C > 
terminal, the cable plug’s < D> icon 
must face the front side of the 
camera.
  Connect the plug on the other end of 
the cable to the computer’s USB port.
d  Transferring Images to a Computer
Preparation for Image Transfer  
						

							
d Transferring Images to a Computer
178
4Set the camera’s power switch to 
.
 When the program selection dialog 
window appears on the computer, 
select [ EOS Utility ].
X The [ EOS Utility ] window will appear 
on the computer, and the direct image 
transfer screen will appear on the 
camera’s LCD monitor.
The images sent to the computer will be saved in the [ My Pictures] 
folder or [ Pictures] folder in subfolders organized according to the 
shooting date.
 All images
This is to transfer all the images in the 
card to the computer.
 Select [ All Images ], then press the 
< l > button.
X The < l> button’s blue lamp will 
blink and the image transfer will start.
X When the image transfer is 
completed, the lamp will stay on.
Transferring Images to a Computer
  If the [ EOS Utility ] window does not appear automatically, startup EOS 
Utility manually.
  Before disconnectin g the cable, turn off the ca mera. Pull out the cable by 
grasping the plug (i nstead of the cord).
 Since movie files are larger than still  photo files, they will take longer to 
transfer.
  During the file transfer, do  not disconnect the cable.
  Shooting will be disabled while the  direct transfer screen is displayed.  
						

							
179
d Transferring Images to a Computer
Options other than [ All images] are explained below. To start the image 
transfer, press the < l> button.
  New images
Images which have not yet been trans ferred to the computer will be 
selected by the camera automatically and transferred.
  Transfer order images
You select the images and they are  transferred to the computer in a 
batch. To select the images, see page 180.
  Select & transfer
You select the images to be transferred 
individually. To exit, press the < M> 
button.
  Wallpaper
The image you select and transfer  will appear as the computer’s 
wallpaper. To exit, press the < M> button.
 If you press  instead of the < l> button, a confirmation dialog 
will appear. Select [ OK], then press  to start the transfer.
  RAW images and movies cannot  be transferred as wallpaper.  
						

							
d Transferring Images to a Computer
180
Under the [ 3] tab, you can use 
[ Transfer order ] to select the images to 
be transferred to a computer.
When you select [ Transfer order 
images ] on page 179, you can transfer 
the images set by  the transfer order.
 Sel.Image
Select and order images one by one. 
Press the  key to include the 
displayed image in the transfer order. 
The < X> mark will also appear on the 
upper left.
After completing the transfer order, press 
the < M > button to save the transfer 
order to the card.
  All image
If you select [ Mark all on card ], all the images in the card will be in 
the transfer order. If you select [ Clear all on card], the transfer order 
will be cleared for all t he images in the card.
3 Selecting the Images to be Transferred
Do not put into the came ra any images whose tran sfer order was set by a 
different camera and then  try to specify another transfer order. The images 
in the transfer order mi ght all be overwritten. Al so, depending on the image 
type, the transfer ord er may not be possible.
 For the transfer order, if you  select an image captured in the 1+73  
mode, it will be counted  as one image. During the direct image transfer, 
both the RAW and JPEG  images will be transferred to the computer.
  If you want to transfer  more than 999 images in one ba tch, select [All 
images ] on the direct tran sfer screen (p.178).