Canon 5dsr Manual

441
14
Reference
This chapter provides reference information for camera 
features, system accessories, etc.
Certification Logo
Select [54: Certification Logo Display ] and press  to 
display some of the logos of the camera’s certifications. Other 
certification logos can be found in this Instruction Manual, on the 
camera body, and on the camera’s package. 

442
When the camera is ready to shoot, 
pressing the  button can switch 
the display as follows: Camera settings, 
Electronic level (p.75), Quick Control 
screen (p.60), and Custom Quick Control 
screen (p.427).
Under the [ 53] tab, [ z button 
display options] enables you to select 
the options displayed when the < B> 
button is pressed.
 Select the desired display option and 
press < 0> to append a checkmark 
[X].
 After completing the selections, select 
[OK ].
B  Button Functions
Camera settings...

443
B Button Functions
* This icon is displayed when the transfer of some images failed.
Camera Settings
If you turn off the power while the Electronic level, Quick Control screen, 
or Custom Quick Control screen is displayed, the same screen will be 
displayed when you turn on the power  again. To cancel this function, 
press the < B> button a number of times until the screen is blank, 
then turn off the power switch.
 Note that you cannot remove the [ X] for all four display options.
 The [ Displays...

B Button Functions
444
For the Custom Quick Control screen, see page 427.
Quick Control Screen
Custom Quick Control Screen
AE lockHighlight tone priority
ISO speed
Exposure 
compensation
Custom Controls
Card selection icon
Card indicator Image-recording 
quality
Possible shots
Maximum burst/Number of 
remaining multiple exposures
Multiple exposures/HDR/
Multi Shot Noise Reduction Auto Lighting 
Optimizer
Flash-ready/FE lock/
High-speed sync
Aperture
Shutter speed
Shooting mode
Exposure
compensation
White...

445
B Button Functions
When you press the , , , or  button, 
the setting screen appears and you can use < 6>, , < 9>, or 
< B > to set the functions.
Button Functions for the Quick Control and 
Custom Quick Control Screens
Metering mode / White balance AF operation / Drive mode
AF point selectionISO speed / 
Flash exposure compensation 

446
You can check the battery’s condition on the LCD monitor. Each Battery 
Pack LP-E6N/LP-E6 has a unique serial number, and you can register 
multiple batteries to the camera. When you use this feature, you can 
check the registered batteries’ appr oximate remaining capacity and 
operation history.
Select [Battery info.].
Under the [5 3] tab, select [ Battery 
info. ], then press < 0>.
 The battery info. screen will appear.
     (Green): Battery’s recharge performance is fine.
     (Green): Battery’s...

447
3 Checking the Battery Information
You can register up to six LP-E6N/LP-E6 batteries to the camera. To 
register multiple batteries to the camera, follow the procedure below for 
each battery.
1Press the  button.
With the battery info. screen 
displayed, press the < B> button.
 The battery history screen will 
appear.
 If the battery is not registered, it will 
be grayed out.
2Select [Register].
The confirmation dialog will appear.
3Select [OK].
The battery will be registered and the 
battery...

3 Checking the Battery Information
448
It is convenient to label each regi stered Battery Pack LP-E6N/LP-E6 
with their serial numbers, using commercially-available labels.
1Write the serial number on a 
label.
Write the serial number displayed on 
the battery history screen on a label 
approx. 25 mm x 15 mm / 1.0 in. x 0.6 
in. in size.
2Remove the battery  and affix the 
label.
 Set the power switch to < 2>.
 Open the battery compartment cover 
and remove the battery.
 Affix the label as shown in...

449
3 Checking the Battery Information
You can check the remaining capacity of any battery (even when not 
installed) and also when it was last used.
Look for the serial number.
Refer to the battery’s serial number 
label and look for the battery’s serial 
number on the battery history screen.
 You can check the respective 
battery’s remaining capacity and the 
date when it was last used.
1Select [Delete info.].
 Follow step 2 on page 447 to select [ Delete info.], then press 
< 0 >.
2Select the...

450
You can power the camera with a household power outlet by using the 
DC Coupler DR-E6 and AC Adapter AC-E6N (both sold separately).
1Connect the DC Coupler’s plug.
Connect the DC Coupler’s plug to the 
AC Adapter’s socket.
2Connect the power cord.
Connect the power cord as shown in 
the illustration.
 After using the camera, unplug the 
power plug from the power outlet.
3Place the cord in the groove.
Insert the DC Coupler’s cord to the 
groove carefully without damaging 
the cord.
4Insert the DC...