Candy Trio 503 1 Manual

41
If you wish to change or cancel a programme that is running, carry out the following procedure:
. open the door, keeping the Programme selection button P pressed in until all 4 indicator
lights are flashing. The current programme is cancelled. A new setting can now be made.
Before starting a new programme, you should check that there is still detergent in the
dispenser. If necessary, top up the dispenser.
WARNING: if the door is opened during the drying phase, an intermittent audible signal is...

42
PRELIMINARY  OPERATIONS  AND  CLEANING  THE  FILTER  UNIT
The filtering system is composed of :
- a central filter cup which traps the largest food particles.
- a flat filter which continuously filters the washing water.
- the micro filter, situated under the flat filter, which traps the
smallest food particles ensuring a perfect rinse.
For best results, the filter unit should be checked and cleaned after each wash.
To remove the filter unit, simply grip the handle and lift the whole unit out.
The...

43
LOADING  THE  DETERGENT
It is essential to use a detergent that is specifically designed for dishwashers either
in powder, liquid or tablet form.
Unsuitable detergents, (like those for washing up by hand) do not contain the proper
ingredients for use in a dishwasher and impede the efficient functioning.
Normal wash
The detergent dispenser is inside the door. The dispenser
lid should be closed before every wash.To open it, simply
press the catch. At the end of each wash cycle the lid is
always open and...

44
REGULATING THE RINSE AID (from 1 to 6).
The regulator control B is below the indicator and can be turned with the finger, the
recommended position is 3.
The hardness of the water can be judged by incrustation or by the level of dryness.
It is therefore important that the correct dosage of Rinse Aid is regulated to give the best
results.
After the wash,
. if streaks occur on the dishes, decrease the amount by one position.
. if whitish spots occur, increase the amount by one position.
LOADING THE SALT...

45
Regulating the water softener with electronic programmer
The water softener can treat water with a hardness level of up to 60°Fh (French grading) or
33°Dh (German grading) through 5 settings.
The settings are listed in the panel below:
The softener unit is set in the factory at level 3 (indicator light N.3) as this is suitable for the
majority of users.
Regulate the setting of your water softener unit according to the degree of hardness of your
water as follows: Open the door, press On / Off button,...

46
Duration
Detergent for soaking
Detergent for washing
Clean filter
Check rinse aid dispenser
Check salt dispenser
Hot pre-wash
Cold Pre-wash
Main wash
First rinse
Second rinse cold
Rinse with rinse aid
With cold water
Intensive
Once a day - for heavily soiled pans
 
and any other items that have been
 
left all day for washing.
75°C
90
Normal
Once a day - for normal soiled pans
 
and any other items that have been
 
left all day for washing
65°C
80
Eco
Energy Saving Programme suitable
 
for normal soi...

47
SOME PRACTICAL HINTS .... To carry out a wash programme with a full load of dishes
load the machine correctly after each meal and do a cold pre-wash between each load
to get rid of stains and remove the larger residues of food.
HOW TO GET GOOD WASH RESULTS
1) Place the dishes face downwards.
2) Try to place the dishes in such a way that they are not touching one another. If they are
loaded properly you will get better results.
3) Before placing the dishes in the dishwasher remove any remaining food...

48
WATER  CONNECTION  -  WATER  DRAINAGE
WATER CONNECTION :
The inlet and drain hoses can be directed to left or right.
The dishwasher can be connected to either cold or hot water, as long as it is no hotter than
60°C.
Water pressure mut be between 0,08 MPa and 0,8 MPa. If the pressure is below the
minimum consult the service department for advice.
The inlet hose must be connected to a tap so that the water supply can be cut off when the
machine is not in use (fig.1). The dishwasher inlet hose is fitted...

49
The hose can be hooked over the side of the sink (it must not be immersed in water, in
order to prevent water from being siphoned back to the machine when this is in operation).
Check that there are no kinks in the inlet and outlet hoses. To extend, if necessary the intlet
hose, contact the Customer Service. 

50
IDENTIFYING MINOR FAULTS
REMEMBER! the oven and the dishwasher cannot be used in the same time.
Should the dishwasher fail to operate, before contacting the Service Centre, make the
following checks:
FAULT CAUSE REMEDY
Plug is not connected correctly Connect electric plug
O/I button has not been pressed Press button
No electricity Check the electricity supply
Door is open Close door
See causes for No 1 Check 
Water tap is turned off Turn water tap on
Programme selector is not at 
correct positionTurn...