Candy Holiday 084 Df User Instructions

							 
  41
l.
  Do not touch the appliance when hands or feet are wet 
or damp. Do not use the appliance with bare feet; 
 
 
 
 
 
 
 
m.  Check there is no water left in the drum before 
opening the door;    
 
 
 
WARNING! 
During the washing cycle, the water can reach a temperature of 90° С. 
 
n.  Glass fibre curtains should never be put into this machine; 
N.B!  If the appliance is installed on a carpeted floor ensure that the ventilation holes on 
the sheet are not obstructed. 
o. Lint or fluff must not be allo wed to collect on the floor ar ound the outside of this ma-
chine; 
p. Always ensure that the door locked indicator neon has switched itself off before opening 
the door. By doing so the machine is allowed to  cool down before the laundry is handled; 
q. Always ensure that the base panel is fitted to the machine. 
r.   If the appliance is not  running properly or breaks down, sw itch it off, turn off the tap and 
do not tamper with the appliance. 
Consult only the Authorised Technical Support Service for possible repair and ask them to 
use original spare parts. 
Failure to comply with the above can compromise the safety of the appliance. 
If the appliance’s power cable should ever need replacing, consult the Authorised Techni-
cal Support Service. 
 
						

							 
 
42
Quick Start 
Washing 
– Press the button inside the door handle to open the door. 
– Select laundry and put it in the machine. 
– Close the door. 
– Put detergent in the dispenser compartments, compartment 
1 for pre wash and com-
partment 2  for all other programs. 
– Select program by turning the program knob (Your desired program may be seen on the 
display).  –  Select any function buttons required; 
–  Press the Start/Pause button (
); 
– There may be a short time delay from pressing the start/pause bottom to the start of the 
program, while the machine senses the water required and sets the parameters for the 
program. 
 
When the program has finished 
  The display will read “END”. 
  Wait for the door lock to be released (about 2 minutes after the program has finished). 
  Switch off the machine by turning the program selector to the “OFF” position. 
  Open the door and remove the laundry. 
  Disconnect the plug from the mains power supply and turn off the water supply after 
every use. 
 
 
Useful advice for users 
Tips on using your domestic appliance in the most environmentally-friendly and economi-
cal way. 
Do a full load in your washing machine. 
To prevent any possible waste of energy, water or detergent we recommend that 
you put a full load in your washing machine, not exceed the maximum load size. 
Save up to 50% energy by washing a full load instead of 2 half loads. 
 
When is prewashing really needed? 
Only with particularly dirty loads! Energy savings of 5 to 15% are made by not selecting the 
prewash option for normally soiled laundry. 
 
Which wash temperature should you choose? 
Using stain removers before machine washing reduces the need to wash at temperatures 
over 60°C. Energy savings of up to 50% can be made by using a 60°C wash temperature. 
 
 
						

							 
  43
Installation
 
 
After removing the machine from the packaging, proceed as 
follows: 
On the back of the machine: 
 
 
 
 
 
 
1) Fix the sheet of corrugated material on the bottom as it is 
shown on picture. You can find the fastener means in the 
instruction booklet pack. 
 
N.B!  If the appliance is installed on a carpeted floor en-
sure that the ventilation holes on the sheet are not ob-
structed. 
 
 
 
2) Remove the 4 fixing screws marked ( A) 
and remove the 4 spacers marked (B )
 
 
3) Cover the 4 holes using the caps provided 
in the instruction booklet pack.
 
 
  
 
 
Note: we recommend you keep the spac ers and screws to immobilize the ma-
chine for future transit. The Manufacture rs will not be responsible for any possi-
ble damage to the machine caused by not following the rules relating to releasing 
the mechanism. The user is responsible for all costs of installation. 
 
WARNING!  
Do not leave the packaging in the reach of chil dren as it is a potential source of danger. 
 
 
						

							 
 
44
4) Carefully cut the securing strap that holds the main cord 
and the drain hose.
  
 
 
 
 
 
5) Us

e the 4 feet to level the machine with the floor: 
A) Turn the nut clockwise to release the screw adjuster of 
the foot. 
 
B) Rotate foot to raise or lower it until it stands firmly on 
the ground. 
 
C) Lock the foot in position by turning the nut anti-
clockwise until it comes up against the bottom of the ma-
chine. 
 
 
ATTENTION! 
Should it be necessary to replace the supply cord, connect the wire in accordance with the 
following colours/codes: 
 
BLUE      - NEUTRAL (N) 
BROWN  - LIVE (L) 
YELLOW-GREEN  - EARTH (     )  
 
If the appliance’s power cable should ever need replacing, consult the Authorized Techni-
cal Support Service.
 
 
						

							 
  45
Water supply
 
The machine has an inlet hose with ¾ threaded ferrules 
fitted to the ends to attach between the threaded connec-
tor on the appliance and the cold water supply.  
Th

e appliance must be connected to the water mains us-
ing new hose-sets. The old hose-sets should not be re-
used. 
The appliance must only be connected to the cold water 
supply. 
Connection to a warm water su pply, that is over 40°, may 
damage certain delicate fabrics.
 
Note: it is advisable to turn off the tap after each 
wash to isolate the washing machine from the water 
supply. 
Position the washing machine next to the wall. Hook the 
outlet tube to the edge of the bath tub, paying attention 
that there are no bends or contractions along the tube. 
If the inlet hose’s connection  point is changed, check that 
the ¾ threaded ferrule on the inlet hose is firmly attached 
to the electrovalve connector. 
 
For the washing machine to function proper ly the terminal end of the discharge 
hose (mouth) must be at a minimum of 50 cm and a maximum of 85 cm from the 
ground. 
  
  
 
 
						

							 
 
46
Description of controls
 
 
 
 
Door handle А 
Door locked indicator  В 
“Start/Pause” button С 
“Aquaplus” button D 
“Cold Wash” button Е 
Start delay button F 
Spin speed button G 
Digital display H 
Buttons indicator light М 
Program selector with OFF position N 
Detergent Drawer  Р 
 
 
						

							 
  47
Description of controls 
Door handle  
А 
Press the finger-bar inside the door handle to open the door. 
IMPORTANT!  
A special safety device prevents the door from opening at 
the end of the wash/spin cycle. At the end of the spin phase 
wait up to 2 minutes before opening the door. 
 
 
Door locked indicator  B 
The “Door Locked” indicator light is illuminated when the door is fully closed and the ma-
chine is ON. 
When “START/PAUSE ” is pressed on the machine with the door closed the indicator will 
flash momentarily and then illuminate. 
If the door is not closed the indicator will continue to flash. 
A special safety device prevents the door from being opened immediately after the end of 
the cycle. 
Wait for 2 minutes after the wash cycle has finished and the Door Locked light has gone 
out before opening the door. At the end of cycle turn the program selector to OFF. 
 
“Start/Pause” button  С 
Press START/PAUSE to start the selected cycle. 
NOTE: When the start button has been  pressed, the appliance can take few sec-
onds before starts working. 
CHANGING THE SETTINGS AFTER THE PROGRAMS HAS STARTED (PAUSE) 
Press and hold the “ START/PAUSE” button for about 2 seconds, the flashing lights on the 
options buttons and time remaining indicator will show that the machine has been paused, 
adjust as required and press the “ START/PAUSE” button again to cancel the flashing 
lights. 
If you wish to add or remove items during washing, wait 2 minutes until the safety device 
unlocks the door. 
When you have carried out the manoeuvre, close the door, press “ START/PAUSE” button 
and the appliance will contin ue working where it left off. 
 
 
 
						

							 
 
48
CANCELLING THE PROGRAM 
To cancel the program, set the 
selector to the OFF position. 
Select a different program. 
Re-set the program selector to the OFF position. 
The option buttons should be sel ected before pressing the “START/PAUSE ” button.  
  
“Aquaplus” button 
 D 
By pressing this button you can activa te a special new wash cycle in the Colourfast and 
Mixed Fabrics  programs, thanks to the new Sensor Acti va System. This option treats with 
care the fibres of garments and the delicate skin of those who wear them. 
The load is washed in a much larger quantity of water and this, together with the new 
combined action of the drum rotation cycles,  where water is filled and emptied, will give 
you garments which have been cleaned and rinsed to perfection. The amount of water in 
the wash is increased so that the detergent dissolves perfectly, ensuring an efficient clean-
ing action. The amount of water is also increased during the rinse procedure so as to re-
move all traces of detergent from the fibres. 
This function has been specifically designed for people with delicate and sensitive skin, for 
whom even a very small amount of detergent can cause irritation or allergy. 
You are advised to also use this function for children’s clothing and for delicate fabrics in 
general, or when washing garments made of towelling, where the fibres tend to absorb a 
greater quantity of detergent. 
To ensure the best performance for your wash, this function is always activated on the 
Delicates and Woollens/Hand wash programs.  
 
“Cold Wash” button
  E 
By pressing this button it is possible to transform every programme into a cold washing 
one, without modify other characteristics  (water level, times, rhythms, etc..). 
Curtains, small carpets, man made delicate fabrics, non colour fast garments can be safely 
washed thanks to this new device. 
 
 
						

							 
  49
Start delay button  F 
This button allows you to preprogram the w
ash cycle to delay the start of the cycle 
for up to 24 hours. 
To delay the start use the following procedure: 
   Set the required program; 
   Press the button once to activate it (h00 appears on the display) and then press it again 
to set a 1 hour delay (h01 appears on the display). The pre-set delay increases by 1 hour 
each time the button is pressed, until h24 appears on the display, at which point pressing 
the button again will reset the delay start to zero. 
Confirm by pressing the “ START/PAUSE” button (the light on the display starts to flash). 
The countdown will begin and when it has finished the program will start automatically. 
It is possible to cancel the delay start by taking the following action: 
   Press and hold the button for 5 seconds until the display will show the settings for the 
program selected. 
At this stage it is possible to start the program previously selected by pressing the 
“ START/PAUSE ” button or to cancel the process by setting the selector to the OFF posi-
tion and then selecting another program. 
 
Spin speed button  G 
The spin cycle is very important to remove  as much water as possible from the laundry 
without damaging the fabrics. You can adjust the spin speed of the machine to suit your 
needs. 
By pressing this button, it is possible to reduce the maximum speed, and if you wish, the 
spin cycle can be cancelled. 
To reactivate the spin cycle is enough to press the button until you reach the spin speed 
you would like to set. 
For not damage the fabrics, it is not possible to increase the speed over that 
automatically suitable during the selection of the program. 
It is possible to modify the spin speed in any moment, also without to pause the ma-
chine. 
NOTE: The machine is fitted with a special  electronic device, which prevents the 
spin cycle should the load be unbalanced. This reduces the noise and vibration in 
the machine and so prolongs the life of your machine. 
 
 
 
						

							 
 
50
Digital display H 
 
The dis

play’s indicator system allows you to be constantly 
informed about the status of the machine:
  
 
1) SPIN SPEED 
Once the program has been selected, the maximum spin 
speed allowed for that program appears on the display. 
Pressing the spin button will reduce the speed by 100 rpm each time the button is pressed. 
The minimum speed allowed is 400 rpm, or it is possible to omit the spin by pressing the 
spin button repeatedly. 
2) DELAY START LIGHT   
This flashes when delay start has been set. 
 
3) PROGRAMME START LIGHT 
This lights up when the START/PAUSE button has been pressed. 
4) CYCLE DURATION 
When a program is selected the display au tomatically shows the maximum cycle duration 
for a full load, which can vary, depending on the options selected. 
Once the program has started you will be kept informed constantly of the time remaining to 
the end of the wash. 
 
The appliance calculates the time to th e end of the selected programme based upon 
a standard loading, during the cycle, the a ppliance corrects the time to that applica-
ble to the size and composition of the load.  
 
Buttons indicator light M  
These light up when the relevant buttons are pressed. 
If an option is selected that is not compatible with the selected programme then the light on 
the button first flashes and then goes off.