Candy Holiday 084 Df User Instructions

 
  41
l.
  Do not touch the appliance when hands or feet are wet 
or damp. Do not use the appliance with bare feet; 
 
 
 
 
 
 
 
m.  Check there is no water left in the drum before 
opening the door;    
 
 
 
WARNING! 
During the washing cycle, the water can reach a temperature of 90° С. 
 
n.  Glass fibre curtains should never be put into this machine; 
N.B!  If the appliance is installed on a carpeted floor ensure that the ventilation holes on 
the sheet are not obstructed. 
o. Lint or fluff must...

 
 
42
Quick Start 
Washing 
– Press the button inside the door handle to open the door. 
– Select laundry and put it in the machine. 
– Close the door. 
– Put detergent in the dispenser compartments, compartment 
1 for pre wash and com-
partment 2  for all other programs. 
– Select program by turning the program knob (Your desired program may be seen on the 
display).  –  Select any function buttons required; 
–  Press the Start/Pause button (
); 
– There may be a short time delay from pressing the...

 
  43
Installation
 
 
After removing the machine from the packaging, proceed as 
follows: 
On the back of the machine: 
 
 
 
 
 
 
1) Fix the sheet of corrugated material on the bottom as it is 
shown on picture. You can find the fastener means in the 
instruction booklet pack. 
 
N.B!  If the appliance is installed on a carpeted floor en-
sure that the ventilation holes on the sheet are not ob-
structed. 
 
 
 
2) Remove the 4 fixing screws marked ( A) 
and remove the 4 spacers marked (B )
 
 
3)...

 
 
44
4) Carefully cut the securing strap that holds the main cord 
and the drain hose.
  
 
 
 
 
 
5) Us

e the 4 feet to level the machine with the floor: 
A) Turn the nut clockwise to release the screw adjuster of 
the foot. 
 
B) Rotate foot to raise or lower it until it stands firmly on 
the ground. 
 
C) Lock the foot in position by turning the nut anti-
clockwise until it comes up against the bottom of the ma-
chine. 
 
 
ATTENTION! 
Should it be necessary to replace the supply cord, connect the...

 
  45
Water supply
 
The machine has an inlet hose with ¾ threaded ferrules 
fitted to the ends to attach between the threaded connec-
tor on the appliance and the cold water supply.  
Th

e appliance must be connected to the water mains us-
ing new hose-sets. The old hose-sets should not be re-
used. 
The appliance must only be connected to the cold water 
supply. 
Connection to a warm water su pply, that is over 40°, may 
damage certain delicate fabrics.
 
Note: it is advisable to turn off the tap...

 
 
46
Description of controls
 
 
 
 
Door handle А 
Door locked indicator  В 
“Start/Pause” button С 
“Aquaplus” button D 
“Cold Wash” button Е 
Start delay button F 
Spin speed button G 
Digital display H 
Buttons indicator light М 
Program selector with OFF position N 
Detergent Drawer  Р 
 
 

 
  47
Description of controls 
Door handle  
А 
Press the finger-bar inside the door handle to open the door. 
IMPORTANT!  
A special safety device prevents the door from opening at 
the end of the wash/spin cycle. At the end of the spin phase 
wait up to 2 minutes before opening the door. 
 
 
Door locked indicator  B 
The “Door Locked” indicator light is illuminated when the door is fully closed and the ma-
chine is ON. 
When “START/PAUSE ” is pressed on the machine with the door closed the indicator...

 
 
48
CANCELLING THE PROGRAM 
To cancel the program, set the 
selector to the OFF position. 
Select a different program. 
Re-set the program selector to the OFF position. 
The option buttons should be sel ected before pressing the “START/PAUSE ” button.  
  
“Aquaplus” button 
 D 
By pressing this button you can activa te a special new wash cycle in the Colourfast and 
Mixed Fabrics  programs, thanks to the new Sensor Acti va System. This option treats with 
care the fibres of garments and the delicate...

 
  49
Start delay button  F 
This button allows you to preprogram the w
ash cycle to delay the start of the cycle 
for up to 24 hours. 
To delay the start use the following procedure: 
   Set the required program; 
   Press the button once to activate it (h00 appears on the display) and then press it again 
to set a 1 hour delay (h01 appears on the display). The pre-set delay increases by 1 hour 
each time the button is pressed, until h24 appears on the display, at which point pressing 
the button...

 
 
50
Digital display H 
 
The dis

play’s indicator system allows you to be constantly 
informed about the status of the machine:
  
 
1) SPIN SPEED 
Once the program has been selected, the maximum spin 
speed allowed for that program appears on the display. 
Pressing the spin button will reduce the speed by 100 rpm each time the button is pressed. 
The minimum speed allowed is 400 rpm, or it is possible to omit the spin by pressing the 
spin button repeatedly. 
2) DELAY START LIGHT   
This flashes...