Candy Go4 1264 D User Instructions

  
• Do not use adaptors or multiple plugs; 
• Do not allow the appliance to be used by children 
or the incompetent without due supervision; 
• Do not pull the mains lead or the appliance itself 
to remove the plug from the socket; 
• Do not leave the appliance exposed to atmos-
pheric agents (rain, sun etc.); 
• In the case of removal, never lift the appliance by 
the knobs or detersive drawer; 
• During transportation do not lean the door against 
the trolley; 
 
Important! 
When the appliance...

  
CHAPTER 4 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
TECHNICAL DATA   
Maximum wash load dry kg 6 
Supply voltage 
 
V 220-240 
Power current fuse amp А 10 
Power input W 2150 
Energy consumption (prog. 90°C) kWh 1,8 
Normal water level l 6…15 
Water pressure МРа min. 0,05  
max. 0,8 
SPIN r.p.m. See rating plate 
 
 
 42 
 

  
CHAPTER 5  
 
SETTING UP INSTALLATION 
 
Move the machine near its permanent position 
t the packaging base. withou
 
Carefully cut the securing strap that holds the main 
and the drain hose. cord 
 
Remove the 4 fixing screws marked (A) and re-
e the 4 spacers marked (B). mov
 
Cover the 4 holes using the caps provided in the 
instruction booklet pack. 
 
 
 WARNING!  
DO NOT LEAVE THE PACKAGING IN THE 
REACH OF CHILDREN AS IT IS A POTENTIAL 
SOURCE OF DANGER. 
 
 43 
 

  
Connect the fill hose to the tap. 
 
The appliance must be connected to the water 
mains using new hose-sets. The old hose-sets 
should not be reused. 
 
WARNING! 
Do not turn the tap on a
 
t this time. 
 
Position the washing machine next to the wall. 
Hook the outlet tube to the edge of the bath tub, 
paying attention that there are no bends or con-
tractions along the tube, 
It is better to connect the discharge hose to a fixed 
outlet of a diameter greater than that of the outlet 
tube and at a...

  
Use front feet to level the machine with the floor. 
 
a) Turn the nut clockwise to release the screw ad-
juster of the foot. 
 
 
b) Rotate foot to raise or lower it until it stands 
firmly on the ground. 
 
 
c) Lock the foot in position by turning the nut anti-
clockwise until it comes up against the bottom of 
the machine. 
 
 
Ensure that the knob is on the OFF position and 
the load door is closed.  
 
 
Insert the plug. 
 
 
After installation, the appliance must be positioned 
so that the...

  
CHAPTER 6  
  
 
CONTROLS  
Door handle А 
Door locked indicator light В 
TART/PAUSE button SС 
CREASE GUARD button D 
ATURE button WASH TEMPERЕ 
START DELAY button F 
AQUAPLUS button G 
PRE-WASH button Н 
SPIN SPEED button 
 46 
I 
Digital Display L 
DEGREE OF SOILING button М 
Timer knob for wash programs with OFF position N 
Buttons indicator light O 
Detergent drawer 
 
 
Р 
 

 47 
 
   
DESCRIPTION OF CONTROL   
DOOR HANDLE 
de the door handle to open the door. 
 
Press the finger-bar insi
IMPORTANT!  
A special safety device prevents the door from opening at the end of 
the wash/spin cycle. At the end of the spin phase wait up to 2 min-
utes before opening the door. 
 
 
 
 
 
 
DOOR LOCKED INDICATOR The “Door Locked” indicator light is illuminated when the door is fully closed and the machine is ON. 
When “START/PAUSE” is pressed on the machine with the door closed the...

   
The option buttons should be selecte
“START/PAUSE” button. 
d before pressing the   
 
CREASE GUARD BUTTON 
Td function (Not available on COTTON pro-
g
ds. 
IXED FABRICS - the water is gradually cooled throughout the 
 and then a delicate spin as-
ntil it is time to unload. When 
ft in water until it is time to unload and the button indicator 
ad, press the Crease Guard but-
eady for emptying. 
I
he Crease Guar
ram) minimizes creases as much as possible with a uniquely 
esigned anti-crease system...

   
“DELAY START” BUTTON 
This button allows you to preprogram the wash cycle to delay the 
art of the cycle for up to 24 hours. 
To delay the start use the following procedure: 
 and 
). 
, 
n 
 dis-
 when it has finished 
ow 
 is possible to start the program previously selected by 
t-
o-
st
• Set the required program; 
• Press the button once to activate it (h00 appears on the display)
then press it again to set a 1 hour delay (h01 appears on the display
The pre-set delay increases by 1 hour each...

   
PRE-WASH BUTTON 
This option is particularly useful for heavily soiled loads and 
can be used only on some programs as shown in the programs 
table. 
Detergent for this program should be added to the compart-
ment of the soap drawer labeled “1” (Please refer to Detergent 
Drawer Section of manual). We recommend you use only 20% 
of the recommended quantities shown on the detergent pack 
and fabric conditioner should not be used for this program. 
 
 
  
 
SPIN SPEED BUTTON 
The spin cycle is very...