Candy Go4 1264 D User Instructions

							
  
• Do not use adaptors or multiple plugs; 
• Do not allow the appliance to be used by children 
or the incompetent without due supervision; 
• Do not pull the mains lead or the appliance itself 
to remove the plug from the socket; 
• Do not leave the appliance exposed to atmos-
pheric agents (rain, sun etc.); 
• In the case of removal, never lift the appliance by 
the knobs or detersive drawer; 
• During transportation do not lean the door against 
the trolley; 
 
Important! 
When the appliance location is on carpet floors, at-
tetion must be paid so as to ensure that there is nno 
obstruction to the bottom vents. 
 
• Lift the appliance in pairs as illustrated in the dia-
gram; 
• In the case of failure and/or incorrect operation, 
turn the washing machine off, close the water inlet 
tap and do not tamper with the appliance. 
Contact a Candy Technical Assistance Centre for 
any repairs and ask for original Candy spare parts.  
 
Avoidance of these norms may compromise the 
safety of the appliance. 
• Should the supply cord (mains cable) be dam-
aged, this is to be replaced by a specific cable avail-
able from the after sales service centre. 
 
 
 
 
 41 
 
						

							
  
CHAPTER 4 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
TECHNICAL DATA   
Maximum wash load dry kg 6 
Supply voltage 
 
V 220-240 
Power current fuse amp А 10 
Power input W 2150 
Energy consumption (prog. 90°C) kWh 1,8 
Normal water level l 6…15 
Water pressure МРа min. 0,05  
max. 0,8 
SPIN r.p.m. See rating plate 
 
 
 42 
 
						

							
  
CHAPTER 5  
 
SETTING UP INSTALLATION 
 
Move the machine near its permanent position 
t the packaging base. withou
 
Carefully cut the securing strap that holds the main 
and the drain hose. cord 
 
Remove the 4 fixing screws marked (A) and re-
e the 4 spacers marked (B). mov
 
Cover the 4 holes using the caps provided in the 
instruction booklet pack. 
 
 
 WARNING!  
DO NOT LEAVE THE PACKAGING IN THE 
REACH OF CHILDREN AS IT IS A POTENTIAL 
SOURCE OF DANGER. 
 
 43 
 
						

							
  
Connect the fill hose to the tap. 
 
The appliance must be connected to the water 
mains using new hose-sets. The old hose-sets 
should not be reused. 
 
WARNING! 
Do not turn the tap on a
 
t this time. 
 
Position the washing machine next to the wall. 
Hook the outlet tube to the edge of the bath tub, 
paying attention that there are no bends or con-
tractions along the tube, 
It is better to connect the discharge hose to a fixed 
outlet of a diameter greater than that of the outlet 
tube and at a height of min. 50 cm.  
If is necessary to use the plastic sleeve supplied. 
 
 
 
 
 
 
 44 
 
						

							
  
Use front feet to level the machine with the floor. 
 
a) Turn the nut clockwise to release the screw ad-
juster of the foot. 
 
 
b) Rotate foot to raise or lower it until it stands 
firmly on the ground. 
 
 
c) Lock the foot in position by turning the nut anti-
clockwise until it comes up against the bottom of 
the machine. 
 
 
Ensure that the knob is on the OFF position and 
the load door is closed.  
 
 
Insert the plug. 
 
 
After installation, the appliance must be positioned 
so that the plug is accessible. 
 
 45 
 
						

							
  
CHAPTER 6  
  
 
CONTROLS  
Door handle А 
Door locked indicator light В 
TART/PAUSE button SС 
CREASE GUARD button D 
ATURE button WASH TEMPERЕ 
START DELAY button F 
AQUAPLUS button G 
PRE-WASH button Н 
SPIN SPEED button 
 46 
I 
Digital Display L 
DEGREE OF SOILING button М 
Timer knob for wash programs with OFF position N 
Buttons indicator light O 
Detergent drawer 
 
 
Р 
 
						

							
 47 
 
   
DESCRIPTION OF CONTROL   
DOOR HANDLE 
de the door handle to open the door. 
 
Press the finger-bar insi
IMPORTANT!  
A special safety device prevents the door from opening at the end of 
the wash/spin cycle. At the end of the spin phase wait up to 2 min-
utes before opening the door. 
 
 
 
 
 
 
DOOR LOCKED INDICATOR The “Door Locked” indicator light is illuminated when the door is fully closed and the machine is ON. 
When “START/PAUSE” is pressed on the machine with the door closed the indicator will flash momentarily and then illuminate. If the door is not closed the indicator will continue to flash. A special safety device prevents the door from being opened immediately after the end of the cycle. Wait for 2 minutes after the wash cycle has finished and the Door Locked light has gone out before opening the door. At the end of cycle turn the program selector to OFF. 
 
 
 
START BUTTON 
Press to start the selected cycle. 
 
NOTE: When the start button has been pressed, the appliance can 
take few seconds before starts working. 
CHANGING THE SETTINGS AFTER THE PROGRAMMES HAS STARTED 
USE” button for about 2 seconds, the flashing 
s and time remaining indicator will show that the 
adjust as required and press the “START/PAUSE” 
flashing lights. 
 items during washing, wait 2 minutes until the 
or. 
rried out the manoeuvre, close the door, press 
on and the appliance will continue working where it left 
(PAUSE) 
Press and hold the “START/PA
lights on the options button
machine has been paused, 
button again to cancel the 
If you wish to add or remove
safety device unlocks the do
When you have ca
“START/PAUSE” butt
off. 
CANCELLING THE PROGRAMME 
To cancel the program: 
• Set the selector to the OFF position. 
• Select a different program. 
• Re-set the program s
  
elector to the OFF position. 
 
 
						

							
   
The option buttons should be selecte
“START/PAUSE” button. 
d before pressing the   
 
CREASE GUARD BUTTON 
Td function (Not available on COTTON pro-
g
ds. 
IXED FABRICS - the water is gradually cooled throughout the 
 and then a delicate spin as-
ntil it is time to unload. When 
ft in water until it is time to unload and the button indicator 
ad, press the Crease Guard but-
eady for emptying. 
I
he Crease Guar
ram) minimizes creases as much as possible with a uniquely 
esigned anti-crease system that is tailored to specific fabric
M
final two rinses with no spinning
sures the maximum relaxation of the fabrics. 
DELICATE FABRICS – final two rinses with no spinning and 
then the fabrics are left in water u
you are ready to unload, press the Crease Guard button – 
this will drain. 
WOLLENS/HAND WASH – after the final rinse the fabrics are 
le
blinking. 
When you are ready to unlo
on, this will drain and spin rt
f you do not want to spin the clothes and activate drain only: 
- Turn the program selector to the OFF position; 
- Select program drain only 
  
; 
- Switch on the appliance again by pressing the “START/PAUSE” 
button. 
“WASH TEMPERATURE” BUTTON 
The Wash Temperature button allows a reduction in th
temperature in each program. 
e wash 
d the temperature decreases un-
ash 
Each time the button is presse
C (cold Wtil a minimum of 15°). 
 adjusted before selecting NOTE: The temperature must be
DEGREE OF SOILING. 
 
  
 48 
 
						

							
   
“DELAY START” BUTTON 
This button allows you to preprogram the wash cycle to delay the 
art of the cycle for up to 24 hours. 
To delay the start use the following procedure: 
 and 
). 
, 
n 
 dis-
 when it has finished 
ow 
 is possible to start the program previously selected by 
t-
o-
st
• Set the required program; 
• Press the button once to activate it (h00 appears on the display)
then press it again to set a 1 hour delay (h01 appears on the display
The pre-set delay increases by 1 hour each time the button is pressed
until h24 appears on the display, at which point pressing the butto
again will reset the delay start to zero. 
Confirm by pressing the “START/PAUSE” button (the light on the
play starts to flash). The countdown will begin and
the program will start automatically. 
It is possible to cancel the delay start by taking the following action: 
• Press and hold the button for 5 seconds until the display will sh
the settings for the program selected. 
•At this stage it 
pressing the “START/PAUSE” button or to cancel the process by se
ting the selector to the OFF position and then selecting another pr
gram. 
  
AQUAPLUS BUTTON 
By pressing this button you can activate a special new wash cycle
the Colourfast and Mixed Fabrics programs, thanks to the new S
 in 
en-
es of garments 
and the delicate 
geuantity of water and this, together 
er 
d 
d to perfection. The amount of water in the wash is increased 
nsuring an efficient cleaning 
sed during the rinse proce-
y designed for people with delicate 
and sensitive skin, for whom 
on children’s clothing and for 
-
ance for your wash, this function is always 
activated on the Delicates and Woollens/Handwash programs. 
sor Activa System. This option treats with care the fibr
o wear them. skin of those wh
The load is washed in a much larr q
with the new combined action of the drum rotation cycles, where wat
is filled and emptied, will give you garments which have been cleane
and rinse
so that the detergent dissolves perfectly, e
action. The amount of water is also increa
dure so as to remove all traces of detergent from the fibres. 
This function has been specificall
 even a very small amount of detergent can
cause irritation or allergy. 
You are advised to also use this functi for
delicate fabrics in general, or when washing garments made of towel
ling, where the fibres tend to absorb a greater quantity of detergent. 
To ensure the best perform
  
 49 
 
						

							
   
PRE-WASH BUTTON 
This option is particularly useful for heavily soiled loads and 
can be used only on some programs as shown in the programs 
table. 
Detergent for this program should be added to the compart-
ment of the soap drawer labeled “1” (Please refer to Detergent 
Drawer Section of manual). We recommend you use only 20% 
of the recommended quantities shown on the detergent pack 
and fabric conditioner should not be used for this program. 
 
 
  
 
SPIN SPEED BUTTON 
The spin cycle is very important to remove as much water as 
achine to suit your needs. 
activate the spin cycle is enough to press the button un-
ed you would like to set. 
possible from the laundry without damaging the fabrics. You 
can adjust the spin speed of the m
By pressing this button, it is possible to reduce the maximum 
speed, and if you wish, the spin cycle can be cancelled. 
To re
til you reach the spin spe
For not damage the fabrics, it is not possible to increase 
the speed over that automatically suitable during the se-
lection of the program. 
It is possible to modify the spin speed in any moment, also 
without to pause the machine. 
 
 
NOTE: The machine is fitted with a special electronic 
device, which prevents the spin cycle should the load 
be unbalanced. This reduces the noise and vibration in 
the machine and so prolongs the life of your machine. 
 
 
 
 
 
   
 
 
 50