Home > Brother > Sewing Machine > Brother S 7200 Manual

Brother S 7200 Manual

Here you can view all the pages of manual Brother S 7200 Manual. The Brother manuals for Sewing Machine are available online for free. You can easily download all the documents as PDF.

Page 11

 
 
S-7200A 
3. INSTALLATION 
5
3. Power switch 
(1) Power switch 
(2)  Screws [2 pcs] 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
4. Oil pan 
(1)  Head cushions (left) [2 pcs] 
(2)  Head cushions (right) [2 pcs] 
(3) Oil pan 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
5. Rubber cushions 
(1)  Rubber cushions [2 pcs] 
(2)  Nails [4 pcs] 
 
6. Knee lifter complying bar 
(3)  Knee lifter complying bar 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
2092M
2093M
Operator 
2094M 

Page 12

 
 
S-7200A 
3. INSTALLATION
6
7. Machine head 
(1) Hinges [2 pcs] 
(2) Machine head 
(3) Head rest 
 
NOTE: 
Tap the head rest (3) securely into 
the table hole. If the head rest (3) is 
not pushed in as far as it will go, the 
machine head will not be sufficiently 
stable when it is tilted back. 
 
 
 
 
 
 
 
 
 
8. Operation panel 
(1) Operation panel 
(2)  Screws [2 pcs] 
(Use for tightening rear cover) 
 
 
 
 
 
 
 
 
 
 
9. Sticker (Remove) 
(1) Sticker 
 
 
 
 
 
 
 
 
 
 
 
 
 
10. Cotton stand...

Page 13

 
 
S-7200A 
3. INSTALLATION 
7
11. Knee lifter plate 
(1)  Knee lifter plate 
(2) Bolt 
 
*  Loosen the bolt (3) and move the 
knee lifter plate (1) to a position 
where it is easy to use. 
 
 
 
 
 
 
 
1.  Turn the machine pulley so that the feed dog is below the 
top of the needle plate. 
2. Lower the presser foot (5) by using the lifting lever (4). 
 
 
 
 
 
 
3.  Loosen the nut (6). 
4.  Turn the screw (8) to adjust so that the amount of play in 
the knee lifter (7) is approximately 2 mm when the...

Page 14

 
 
S-7200A 
3. INSTALLATION
8
3-3. Lubrication (-40[], 43[] specifications) 
* If the sewing machine is -45[] specifications, it is a 
complete dry type machine, and so no lubrication is 
necessary. 
 
      CAUTION 
 
Do not connect the power cord until lubrication has been completed, otherwise the machine may operate if the 
treadle is depressed by mistake, which could result in injury. 
Be sure to wear protective goggles and gloves when handling the lubricating oil and grease, so that they do not get...

Page 15

 
 
S-7200A 
3. INSTALLATION 
9
3-4. Connecting the cords 
     DANGER 
 
Wait at least 5 minutes after turning off the power switch and disconnecting the power cord from the wall outlet 
before opening the face plate of the control box. Touching areas where high voltages are present can result in 
severe injury. 
 
     CAUTION 
 
Contact your Brother dealer or a qualified electrician for any electrical work that may need to be done. 
Do not connect the power cord until all cords have been connected....

Page 16

 
 
S-7200A 
3. INSTALLATION
10
(1)  10-pin operating panel connector 
(2) 14-pin encoder connector 
(3) 14-pin machine connector 
(4)  7-pin head detector unit connector 
 
Refer to the following page for the 4-pin 
motor connector. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
2. Repeat cable tie 
(1)  Repeat cable tie 
 
NOTE: 
y Bind the cords in such a way that the 
connector does not get pulled out. 
y All cords that come out from the 
control box should be secured to the 
cord holder (2) using...

Page 17

 
 
S-7200A 
3. INSTALLATION 
11
3. Other cords 
(1)  6-pin power supply connector 
(2)  4-pin motor connector 
(3) Wire clip 
(4) Power cord 
 
Insert the power cord plug (5) into a 
wall outlet. 
 
1. Attach an appropriate plug to the 
power cord (4). (The green and 
yellow wire is the ground wire.) 
2. Insert the plug into a 
properly-grounded AC power supply. 
NOTE: 
Do not use extension cords, 
otherwise machine operation 
problems may result....

Page 18

 
 
S-7200A 
3. INSTALLATION
12
3-5. Test operation (Operating the treadle) 
     CAUTION 
 
Do not touch any of the moving parts or press any objects against the machine while sewing, as this may result in 
personal injury or damage to the machine. 
 
Press the ON power switch (1). 
The power indicator (2) will illuminate. 
 
NOTE: When turning the power switch on for the first time 
The treadle and the operation panel will not operate for 
approximately four seconds after the power switch is 
turned...

Page 19

 
 
S-7200A 
4. PREPARATION BEFORE SEWING 
13
4. PREPARATION BEFORE SEWING 
4-1. Installing the needle 
     CAUTION 
 Turn off the power switch be fore installing the needle. 
The machine may operate if the treadle is depres sed by mistake, which could result in injury. 
1. Turn the machine pulley to  move the needle bar to its 
highest position. 
2.  Loosen the screw (1). 
3.  Insert the needle (2) in a stra ight line as far as it will go, 
making sure that the long groo ve on the needle is at the...

Page 20

 
 
S-7200A 
4. PREPARATION BEFORE SEWING 
14
2126M 
4-3. Winding the lower thread 
     CAUTION 
 
Do not touch any of the moving parts or press any objects against the machine while winding the lower thread, as 
this may result in personal injury or damage to the machine. 
1.  Turn on the power switch. 
2.  Place the bobbin (1) onto the bobbin winder shaft (2). 
3.  Wind the thread several times around the bobbin (1) in the 
direction indicated by the arrow. 
4.  Push the bobbin presser arm (3) toward...
Start reading Brother S 7200 Manual

Related Manuals for Brother S 7200 Manual

All Brother manuals