Brother S 7200 Manual

 
    
S-7200A  
SINGLE NEEDLE DIRECT DRIVE   
STRAIGHT LOCK STITCHER WITH THREAD TRIMMER 
  

S-7200A i
Thank you very much for buying a BROTHER sewing machine. Before using your new machine, please read the safety 
instructions below and the explanations given in the instruction manual. 
 
With industrial sewing machines, it is normal to carry out work while positioned directly in front of moving parts such as the 
needle and thread take-up, and consequently there is always a danger of injury that can be caused by these parts.    Follow 
the instructions from training personnel and instructors...

S-7200A ii 2. Notes on safety 
 DANGER 
 Wait at least 5 minutes after turning off the power switch and disconnecting the power cord from the wall outlet 
before opening the face plate of the control box. Touching areas where high voltages are present can result in 
severe injury.  
 
 CAUTION 
Environmental requirements 
 
 
 
 
 
 
 
 
 
 
 
 
 
Use the sewing machine in an area which is free 
from sources of strong electrical noise such as 
high-frequency welders. 
Sources of strong electrical noise...

S-7200A iii
 
 CAUTION 
Sewing 
 
 
 
 
 
 
 
 
 
 
 
 
This sewing machine should only be used by 
operators who have received the necessary training 
in safe use beforehand. 
The sewing machine should not be used for any 
applications other than sewing. 
Be sure to wear protective goggles when using the 
machine. 
If goggles are not worn, there is the danger that if a 
needle breaks, parts of the broken needle may 
enter your eyes and injury may result. 
Turn off the power switch at the following...

S-7200A iv
3.Warning labels 
 
The following warning labels appear on the sewing machine. 
Please follow the instructions on the labels at all times when using the machine. If the labels have been removed or are 
difficult to read, please contact your nearest Brother dealer. 
 
1 
 
 
 
 
 
 
 
 
 
 
 
 
 
 2 
3  Be sure to connect the ground. If the ground connection is not 
secure, you run a high risk of receiving a serious electric shock, 
and problems with correct operation may also occur....

S-7200A 
CONTENTS 
 
 
1.  NAMES OF MAJOR PARTS................  1 
2. MACHINE SPECIFICATIONS ..............  
2 
3. INSTALLATION ...................................  
3 
3-1. Table processing diagram ..............................   4 
3-2. Installation ......................................................   4 
3-3. Lubrication (-40[], 43[] specifications) ............   8 
3-4. Connecting the cords .....................................   9 
3-4-1.  Opening the control box cover.............   9...

 
 
S-7200A 
1. NAMES OF MAJOR PARTS   
1
1. NAMES OF MAJOR PARTS 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
(1)   Bobbin winder  (2)   Thread wiper 
(3)   Lifting lever  (4)  Quick reverse (Actuator) 
(5)   Presser foot  (6)   Control box 
(7)    Knee lifter assembly  (8)    Power switch 
(9)    Oil gauge window (-40[], 43[] specifications) (10) Reverse lever 
(11)    Stitch length dial  (12)  Machine pulley 
(13)    Operation panel  (14)  Cotton stand...

 
 
S-7200A 
2. MACHINE SPECIFICATIONS 
2
2. MACHINE SPECIFICATIONS 
 
 
 4 
Quick reverse 
○ 
Thread wiper 
○ 
 
 
 
 
 0 3 5 
Lubrication type Minimum lubrication Semi dry  Complete dry 
 
 
 
 
 S 3 5 
Use For light-weight 
and difficult-to-sew 
materials For medium- 
weight materials For heavy-weight 
materials 
 
 
 
 -43S 
-45S -453 
 -403 
-433 -405 
Max. sewing speed  4,000 rpm  5,000 rpm*  4,500 rpm* 
Start backtacking and continuous 
backtacking speed 220–1,800 rpm 
End backtacking speed  1,800...

 
 
S-7200A 
3. INSTALLATION 
3
3. INSTALLATION 
     CAUTION 
 
 
 
 
 
 
 Machine installation should only be carried out by a 
qualified technician. 
Contact your Brother dealer or a qualified electrician 
for any electrical work that may need to be done. 
The sewing machine weighs more than 50 kg. The 
installation should be carried out by two or more 
people.  
Do not connect the power cord until installation is 
complete. The machine may operate if the treadle is 
depressed by mistake, which could...

 
 
S-7200A 
3. INSTALLATION
4
3-1. Table processing diagram 
y The top of the table should be 40 mm in thickness and should be strong enough to hold the weight and with-stand the 
vibration of the sewing machine. 
y Drill holes as indicated in the illustration below. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
3-2. Installation 
1. Control box 
(1) Control box 
(2)  Bolts [3 pcs] 
(3)  Nuts [3 pcs] 
(4)  Spring washers [3 pcs] 
(5) Washers [3 pcs] 
 
2. Connecting rod 
(6)...