Brother Hl4570cdw Owners Manual

Troubleshooting 
145
6
Paper handling6
First, make sure that you are using paper that meets Brother recommended paper specifications. (See Type 
and size of paper on page 2.)
ProblemRecommendation
The machine does not feed 
paper.If there is paper in the paper tray, make sure it is straight. If the paper is curled, 
straighten it before printing. Sometimes it is helpful to remove the paper. Turn the 
stack over and put it back in the paper tray. If the paper continues to curl, replace 
the paper....

Troubleshooting 
146
6
Paper jams and how to clear them6
If paper jams inside the machine, the machine will stop. One of the following LCD messages will appear to 
tell you where to find the jammed paper.
 
JamMPTray (1)
Paper jam in the MP tray. (See page 147.)
JamTray1 (2)
Paper jam in the standard paper tray (Tray 1). (See page 147.)
JamTray2 (3)
Paper jam in the lower tray (Tray 2). (See page 147.)
Jam Duplex (4)
Paper jam underneath the standard paper tray (Tray 1) or in the fuser unit. (See...

Troubleshooting 
147
6
Jam MP Tray (paper jam in the MP tray)6
 
Jam MP Tray
If a paper jam occurs inside the MP tray, follow these steps:
aRemove the paper from the MP tray.
bRemove any jammed paper from in and around the MP Tray.
cFan the paper stack, and then put it back in the MP tray. 
dWhen loading paper in the MP tray, make sure that the paper stays under the maximum paper height 
guides on both sides of the tray.
ePress Go to resume printing.
Jam Tray 1 / Jam Tray 2 (Paper jam inside the paper...

Troubleshooting 
148
6
If a paper jam occurs inside the paper tray, follow these steps:
aPull the paper tray completely out of the machine. 
WARNING 
DO NOT touch the shaded parts shown in the illustration. These rollers may be rotating at high speed and 
can pinch or entrap your hand.
 
  

Troubleshooting 
149
6
bUse both hands to slowly pull out the jammed paper. 
Note
Pulling out the jammed paper downward allows you to remove the paper easier.
 
cMake sure that the paper is below the maximum paper mark (bbb). While pressing the green 
paper-guide release lever, slide the paper guides to fit the paper size. Make sure that the guides are 
firmly in the slots.
dPut the paper tray firmly back in the machine. 

Troubleshooting 
150
6
Jam Duplex (paper jam underneath the standard paper tray (tray 1) or in the 
fuser unit)6
 
Jam Duplex
If a paper jam occurs inside the duplex unit, follow these steps:
aLeave the machine turned on for 10 minutes to cool down.
bPull the paper tray completely out of the machine and check inside the machine. 
WARNING 
DO NOT touch the shaded parts shown in the illustration. These rollers may be rotating at high speed and 
can pinch or entrap your hand.
 
  

Troubleshooting 
151
6
cIf paper is not caught inside the machine, check underneath the paper tray. 
Note
Do not put the paper tray back in at this point.
 
dIf the paper is not caught in the paper tray, open the back cover. 
WARNING 
After you have just used the machine, some internal parts of the machine will be extremely hot. Wait for the 
machine to cool down before you touch the internal parts of the machine.
 
  

Troubleshooting 
152
6
ePull out the jammed paper slowly. 
fFully close the back cover.
gPut the paper tray back in the machine. 

Troubleshooting 
153
6
Jam Rear (Paper jam behind the back cover)6
 
Jam Rear
If a paper jam occurs behind the back cover, follow these steps:
aLeave the machine turned on for 10 minutes to cool down.
bOpen the back cover. 
WARNING 
After you have just used the machine, some internal parts of the machine will be extremely hot. Wait for the 
machine to cool down before you touch the internal parts of the machine.
 
  

Troubleshooting 
154
6
cPull the green tabs (2) at the left and right hand sides toward you and fold down the fuser cover (1). 
Note
If the envelope levers (3) inside the back cover are pulled down to the envelope position,  lift these levers 
to the original position before pulling the green tabs (2) down.
 
dUsing both hands, gently pull the jammed paper out of the fuser unit. 
12
3 2
3