Brother Hl 4150cdn User Manual

Control Panel 65
3
LEDs3
The LEDs are lights which show the machine status.
Data LED (Green)
3
Error LED (Orange)3
LED indicationMeaning
On Data is in the machine memory.
Blinking Receiving or processing data.
Off No remaining data in the memory.
LED indicationMeaning
Blinking There is a problem with the machine.
Off There is no problem with the machine.
 

Control Panel 66
3
LCD3
The LCD shows the current machine status. When you use the buttons on the control panel, the LCD will 
change.
If there are any problems, the LCD will show the error message, maintenance message, or call service 
message so you will know that you need to take action. (For more information about these messages, see 
LCD messages on page 140.)
Back light3
LCD messages3
The message on the LCD shows the current machine status during normal operation.
 
Ready
Ko Yo Mn Co
The  o and  n...

Control Panel 67
3
Machine status messages3
The following table shows the machine status messages during normal operation: 
1(HL-4570CDW(T) only) When the Wireless Network is enabled the machine does not transfer to Deep Sleep mode. If you want to disa ble the 
Wireless Network, change setting of the WLAN Enable to Off. (See  Network for HL-4570CDW(T) users on page 76.)
Machine Status MessageMeaning
Cooling Down The machine is cooling down.
Job Cancel
Job Cancel (All) Canceling the job.
Ignore Data...

Control Panel 68
3
Reprinting documents3
Reprinting the last job3
You can reprint the data from the last print job without sending it from the computer again.
Note
• The Reprint function is not available when Secure Function Lock 2.0 is On. For more information about Secure Function Lock 2.0, see the  Chapter 6 of the Network Users Guide .
• If the machine does not have enough memory to spool the print job data, it will not print the document.
• If you wait 30 seconds to continue the control panel...

Control Panel 69
3
Printing Secure data3
Secure data3
Secure documents are protected by a password and only those people who know the password will be able 
to print the document. The machine will not print the document when you send it for printing. To print the 
document, you must use the control panel of the machine (with the password). Secure data will be deleted 
after it is printed once.
When the area to spool data is full, the LCD shows Out of Memory. Press Cancel to return to the Ready 
state.
If...

Control Panel 70
3
Menu table3
There are eight menus. For more information about the selections available in each menu, see the tables 
below.
If no control panel operations are performed for 30 seconds, the LCD automatically returns to Ready.
Note
The control panel LCD names for the paper trays are as follows.• Standard paper tray:  Tray1
• Multi-purpose tray:  MP
• Optional lower tray:  Tray2
 
Machine Info.
Submenu Menu Selections Options Descriptions
Print Settings Prints the Printer Settings page....

Control Panel 71
3
Paper Tray3
Drum CountShows the current total pages printed for the drum 
unit.
Parts Life Drum Life Shows the remaining life for the drum unit.
Belt Life Shows the remaining life for the belt unit.
PF KitMP Life Shows the pages left to print with the PF kit MP.
PF Kit1 Life Shows the pages left to print with the PF kit 1.
PF Kit2 Life Shows the pages left to print with the PF kit 2.
Fuser Life Shows the pages left to print with the fuser unit.
Laser Life Shows the pages left to print...

Control Panel 72
3
General Setup3
SubmenuMenu Selections Options Descriptions
Local Language English*/Français... Changes the LCD language for your 
country.
Ecology Sleep Time 0/1 /2 /3 */4 /5 ... Min Sets the time to return to Power Save 
mode.
Toner Save Off*/On Increases the page yield of the toner 
cartridge.
Panel Control Button Repeat 0.1*/0.4/ 0.6/0.8/ 1.0/
1.4/ 1.8/2.0  Sec  Sets the time for the LCD message to 
change when holding 
+ or  - at 
intervals.
Message Scroll
Level 1*/Level 2.../Level...

Control Panel 73
3
Print Menu
SubmenuMenu Selections Options Descriptions
Emulation Auto*/HP LaserJet/
BR-Script 3  Chooses the emulation mode you 
use.
If you choose 
Auto, the machine can 
change the emulation mode 
automatically.
If you choose an option other than 
Auto, each emulation mode will be 
fixed.
Auto Continue Off*/On Chooses whether to automatically 
clear the removable error.
Output Color Auto*/Color/ Mono Sets the output color.
Media Type Plain Paper*/
Thick Paper/
Thicker Paper/
Thin...

Control Panel 74
3
HP LaserJet Font No.I000.../I059 *.../ I071
Font Pitch 0.44 /10* .../99.99
Font Point 4.00 /12* .../999.75
Symbol Set PC-8*... Sets the symbol set or the character 
set.
Table Print Prints code table. 
If Change Emulation  appears on 
the LCD, choose Auto  or 
HP LaserJet in  Emulation of 
Print Menu.
(See page 73.)
Auto LF Off*/On ON: CR i CR+LF, OFF: CR  i CR
Auto CR Off*/On ON: LF i LF+CR, FF  i FF+CR, or 
VT  i VT+CR 
OFF: LF  i LF, FF  i FF, or VT  i VT
Auto WRAP Off*/On Chooses...