Brother Hl 4070cdw User Manual

							Rout i ne  Ma i nt e na nce
102
6
CAUTION 
We recommend that you place the toner cartridges on a clean, flat surface with a piece of disposable paper 
underneath them in case you accidentally spill or scatter toner.
  
DO NOT put a toner cartridge into a fire. It could explode, resulting in injuries.
  
Handle the toner cartridge carefully. If toner scatters on your hands or clothes, wipe or wash it off with cold 
water at once.
  
To avoid print quality problems, DO NOT touch the shaded parts shown in the illustrations.
 
Note
 Be sure to seal up the toner cartridge tightly in a suitable bag so that toner powder does not spill out of the 
cartridge.
 Discard the used toner cartridge according to local regulations, keeping it separate from domestic waste. 
If you have questions, call your local waste disposal office.
     
 
						

							Rout i ne  Ma i nt e na nce
103
6
dClean the corona wire as follows:
1Push to release the latches of the white corona wire cover (1), and then open the cover. 
2Clean the corona wire inside the drum unit by gently sliding the green tab from left to right and right 
to left several times. 
 
CAUTION 
Be sure to return the tab to the home position a (1). If you do not, printed pages may have a vertical stripe.
 
1
1
2
2
2
2
1
1
1
1
1
1
2
2
2
2
1
1
1
1
 
						

							Rout i ne  Ma i nt e na nce
104
6
3Close the corona wire cover.  
4Repeat steps 1 to 3 to clean each of three remaining corona wires.
eUnpack the new toner cartridge. Hold the cartridge with both hands and gently rock it five or six times to 
spread the toner evenly inside the cartridge.
 
fRemove the protective cover. 
1
2
2
2
2
1
1
1
1
 
						

							Rout i ne  Ma i nt e na nce
105
6
gHold the handle of the toner cartridge and slide the toner cartridge into the drum unit. Make sure that you 
match the toner cartridge color to the same color label on the drum unit, and make sure that you fold 
down the toner cartridge handle (1) once the toner cartridge is in place. Repeat this for all the toner 
cartridges.
hPut the drum unit back in the printer. 
iClose the front cover of the printer. 
jTurn on the printer power switch.
CAUTION 
DO NOT turn off the printer power switch or open the front cover until the LCD shows Ready.
    
1.C - Cyan
2.M - Magenta
3.Y - Yellow
4.K - Black
(1) (1)1
2
3
4
 
						

							Rout i ne  Ma i nt e na nce
106
6
Drum unit6
Order No. DR-110CL
A new drum unit can print approximately 17,000 A4 or Letter size single-sided pages.
Note
 There are many factors that determine the actual drum life, such as the temperature, humidity, type of 
paper, type of toner used and so on. Under ideal conditions, the average drum life is estimated at 
approximately 17,000 pages. The actual number of pages that your drum will print may be significantly 
less than this estimate. Because we have no control over the many factors that determine the actual drum 
life, we cannot guarantee a minimum number of pages that will be printed by your drum.
 For best performance, use only genuine Brother toner. The printer should be used only in a clean, dust-
free environment with adequate ventilation.
 Printing with a third-party drum unit may reduce not only the print quality but also the quality and life of the 
printer itself. Warranty coverage does not apply to problems caused by the use of a third-party drum unit.
 
Drum End Soon message6
 
Drum End Soon
If the LCD shows Drum End Soon, it means the drum unit is near the end of its life. We recommend that 
you replace the drum unit with a new one before there is a noticeable deterioration in the print quality.
Replacing the drum unit6
CAUTION 
While removing the drum unit, handle it carefully because it may contain toner.
  
Every time you replace the drum unit, clean the inside of the printer. (See Cleaningon page 123.)
 
aTurn off the printer power switch. Press the front cover release button and then open the front cover. 
 
						

							Rout i ne  Ma i nt e na nce
107
6
bHold the green handle of the drum unit. Lift the drum unit up and then pull it out until it stops. 
cRelease the gray lock lever (1) that is on the left side of the printer. Pull the drum unit completely out of 
the printer using the green handles on the drum unit.
 
CAUTION 
Hold the green handles of the drum unit when you carry it. DO NOT hold the sides of the drum unit.
 
 
 
We recommend that you place the drum unit on a clean, flat surface with a piece of disposable paper 
underneath it in case you accidentally spill or scatter toner.
  
Handle the toner cartridges carefully. If toner scatters on your hands or clothes, wipe or wash it off with cold 
water at once.
 
1
 
						

							Rout i ne  Ma i nt e na nce
108
6
dHold the handle of the toner cartridge and pull it out of the drum unit. Repeat this for all the toner 
cartridges.
 
CAUTION 
To prevent damage to the printer from static electricity, DO NOT touch the electrodes shown in the 
illustration.
 
 
 
To avoid print quality problems, DO NOT touch the shaded parts shown in the illustrations.
     
 
						

							Rout i ne  Ma i nt e na nce
109
6
eUnpack the new drum unit and remove the protective cover. 
CAUTION 
Wait to unpack a drum unit until immediately before you put it in the printer. Exposure to direct sunlight or 
room light may damage the drum unit.
 
fHold the handle of the toner cartridge and slide the toner cartridge into the drum unit. Make sure that you 
match the toner cartridge color to the same color label on the drum unit, and make sure that you fold 
down the toner cartridge handle (1) once the toner cartridge is in place. Repeat this for all the toner 
cartridges.
  1.C - Cyan
2.M - Magenta
3.Y - Yellow
4.K - Black
2
1
(1)
1
2
3
4
 
						

							Rout i ne  Ma i nt e na nce
110
6
gPut the drum unit back in the printer as follows.
1Make sure that the gray lock lever (1) is in the up position and put the drum unit in the printer. Push 
down the gray lock lever (1).
 
Note
When you put the drum unit in the printer, match the green guides (1) of the drum unit handle to the green 
arrows (2) on both sides of the machine.
 
 
2Push the drum unit in until it stops. 
hClose the front cover.
11
2
1
2
1
 
						

							Rout i ne  Ma i nt e na nce
111
6
When you replace the drum unit with a new one, you need to reset the drum counter by completing the 
following steps:
aTurn the printer power switch back on.
bPress the + or - key to choose Machine Info..
cPress OK to proceed to the next menu level, and then press the + or - key to choose 
Reset Parts Life.
dPress OK, and then press the + key to choose Drum Unit.
ePress OK two times.