Brother DCP 9010CN User Manual

							
23
3
3
Paper settings3
Paper Type3
Set up the machine for the type of paper you 
are using. This will give you the best print 
quality.
aPress Menu, 1, 1,  1.
bPress  a or  b to choose  Thin, Plain , 
Thick , Thicker  or 
Recycled Paper .
Press  OK.
cPress  Stop/Exit .
Paper Size3
You can use ten sizes of paper for printing 
copies: A4, Letter, Legal, Executive, A5, 
A5 L, A6, B5, B6 and Folio. 
When you change the size of paper in the 
tray, you will also need to change the setting 
for paper size at the same time so your 
machine can fit the document.
aPress Menu, 1, 1,  2.
bPress  a or  b to choose  A4, Letter , 
Legal , Executive , A5 , A5 L , A6 , B5 , 
B6  or  Folio .
Press  OK.
cPress  Stop/Exit .
Volume settings3
Beeper volume3
When the beeper is on, the machine will beep 
when you press a key or make a mistake. You 
can choose a range of volume levels, from 
High to Off .
aPress  Menu, 1, 2.
bPress  a or  b to choose  Off, Low , Med  or 
High .
Press  OK.
cPress  Stop/Exit .
General Setup3
 
						

							
Chapter 3
24
Ecology features3
Toner Save3
You can save toner using this feature. When 
you set Toner Save to  On, prints appear 
lighter. The default setting is  Off.
a Press  Menu, 1 , 3, 1.
bPress  a or  b to choose  On or  Off .
Press  OK.
cPress  Stop/Exit .
Note
We do not recommend Toner Save for 
printing Photo or Greyscale images.
 
Sleep Time3
The Sleep Time setting can reduce power 
consumption by turning off the fuser while the 
machine is idle.
You can choose how long the machine must 
be idle before it goes into sleep mode. When 
the machine receives computer data or 
makes a copy, the timer will be reset. The 
default setting is 005 minutes.
While the machine is in sleep mode the LCD 
will display  Sleep. When printing or copying 
in sleep mode, there will be a short delay 
while the fuser warms up.
aPress  Menu, 1, 3, 2 .
bEnter the length of time the machine is 
idle before entering sleep mode.
Press  OK.
cPress  Stop/Exit .
LCD Contrast3
You can change the contrast to make the 
LCD look lighter or darker.
aPress Menu, 1, 4.
bPress  a to make the LCD darker. Or, 
press  b to make the LCD lighter.
Press  OK.
cPress  Stop/Exit .
 
						

							
Section II
CopyII
Making copies26
 
						

							
26
4
How to copy4
Copy mode4
 
1 Stack/Sort
2 Copy ratio and Copy layout
3 Contrast
4 Quality
5 Number of copies
Making a single copy4
aLoad your document in the ADF or on 
the scanner glass.
bPress  Mono Start  or Colour Start .
Making multiple copies4
aLoad your document.
bUse the numeric keys to enter the 
number of copies (up to 99).
cPress Mono Start  or Colour Start .
Note
• To sort your copies, see  Sorting copies 
using the ADF  on page 29.
• If the LCD shows  Please Wait and the 
machine stops copying while you are 
making multiple copies, please wait for 30 
to 40 seconds until the machine finishes 
the colour registrations and cleaning 
process of the belt unit.
 
Stop copying4
To stop copying, press  Stop/Exit.
Making copies4
 
						

							
Making copies27
4
Copy options 
(temporary settings)
4
When you want to quickly change the copy 
settings temporarily for the next copy, use the 
temporary Copy keys. You can use different 
combinations.
 
The machine returns to its default settings 
one minute after copying.
Enlarging or reducing the 
image copied4
You can choose the following enlargement or 
reduction ratios:
* The factory setting is shown in Bold with an 
asterisk.
Custom(25-400%)  allows you to enter a 
ratio from  25% to 400% . To enlarge or reduce the next copy follow the 
instructions below:
aLoad your document.
bUse the numeric keys to enter the 
number of copies (up to 99).
cPress 
Enlarge/Reduce .
dDo one of the following:
„ Press  a or  b to choose the 
enlargement or reduction ratio you 
want.
Press  OK.
„ Press  a or  b to choose 
Custom(25-400%) .
Press  OK.
Use the numeric keys to enter an 
enlargement or reduction ratio from 
25%  to 400% . (For example, press 
53  to enter  53%.)
Press  OK.
ePress  Mono Start  or Colour Start .
Note
Page Layout Options 2 in 1(P), 2 in 1(L), 
4in1(P) or 4in1(L) are  not available with 
Enlarge/Reduce.
 
Press
 
100% *
97% LTR iA4
94% A4 iLTR
91% Full Page
85% LTR iEXE
83% LGL iA4
78% LGL iLTR
70% A4 iA5
50%
Custom(25-400%)
200%
141% A5 iA4
104% EXE iLTR
 
						

							
Chapter 4
28
Using the Options key4
Use the  Options  key to quickly set the following copy settings temporarily for the next copy.
Press
 
Menu selections Options Page
Press a or  b, then press  OK
 
Press a or  b, then press  OK
 
Stack/Sort
(appears when the document 
is in the ADF) Stack
*
Sort 29
Brightness b - onnnn + a
b  - nonnn + a
b  - nnonn + a *
b  - nnnon + a
b  - nnnno + a 30
Contrast b - onnnn + a
b  - nonnn + a
b  - nnonn + a *
b  - nnnon + a
b  - nnnno + a 30
Page Layout Off(1 in 1)*
2 in 1 (P)
2 in 1 (L)
4 in 1 (P)
4 in 1 (L) 31
The factory settings are shown in Bold with an asterisk.
 
						

							
Making copies29
4
Improving copy quality4
You can choose from a range of quality 
settings. The default setting is  Auto.
„ Auto
Auto is the recommended mode for 
ordinary printouts. Suitable for documents 
that contain both text and photographs.
„ Photo
Suitable for copying photographs.
„ Text
Suitable for documents containing only 
text.
To  temporarily  change the quality setting, 
follow the steps below:
aLoad your document.
bUse the numeric keys to enter the 
number of copies (up to 99).
cPress  Quality .
dPress a or  b to choose  Auto, Photo  or 
Text .
Press  OK.
ePress  Mono Start  or Colour Start .
To change the  default setting, follow the 
steps below:
aPress  Menu, 2, 1.
bPress  a or  b to choose the copy quality.
Press  OK.
cPress  Stop/Exit .
Sorting copies using the ADF4
You can sort multiple copies. Pages will be 
stacked in the order 1 2 3, 1 2 3, 1 2 3, and so 
on.
aLoad your document in the ADF.
bUse the numeric keys to enter the 
number of copies (up to 99).
cPress Options . Press a or  b to choose 
Stack/Sort .
Press  OK.
dPress  a or  b to choose  Stack or Sort .
Press  OK.
ePress  Mono Start  or Colour Start .
 
						

							
Chapter 4
30
Adjusting Contrast, Colour 
and Brightness4
Contrast4
Adjust the contrast to help an image look 
sharper and more vivid.
To  temporarily  change the contrast setting, 
follow the steps below:
aLoad your document.
bUse the numeric keys to enter the 
number of copies (up to 99).
cPress  Options .
Press  a or  b to choose  Contrast.
Press  OK.
dPress  a or  b to increase or decrease the 
contrast.
Press  OK.
ePress  Mono Start  or Colour Start .
To change the  default setting follow the steps 
below:
aPress  Menu, 2, 3.
bPress  a or  b to increase or decrease the 
contrast.
Press  OK.
cPress  Stop/Exit .
Brightness4
Adjust the copy brightness to make copies 
darker or lighter.
To temporarily  change the copy brightness 
setting, follow the steps below:
aLoad your document.
bUse the numeric keys to enter the 
number of copies (up to 99).
cPress  Options .
Press  a or  b to choose  Brightness .
Press  OK.
dPress  a to make a lighter copy or press 
b  to make a darker copy.
Press  OK.
ePress  Mono Start  or Colour Start .
To change the  default setting follow the steps 
below:
aPress  Menu, 2, 2.
bPress  a to make a lighter copy or press 
b  to make a darker copy.
Press  OK.
cPress  Stop/Exit .
Colour saturation4
You can change the default setting for colour 
saturation.
To change the  default setting follow the steps 
below:
aPress  Menu, 2, 4 .
bPress  a or  b to choose  1.Red, 
2.Green , or 3.Blue .
Press  OK.
cPress  a or  b to increase or decrease the 
colour saturation.
Press  OK.
dReturn to step b to choose the next 
colour. Or press  Stop/Exit.
 
						

							
Making copies31
4
Making N in 1 copies 
(page layout)4
You can reduce the amount of paper used 
when copying by using the N in 1 copy 
feature. This allows you to copy two or four 
pages onto one page, which lets you save 
paper.
IMPORTANT
• Please make sure the paper size is set to 
A4 , Letter , Legal  or Folio .
•( P) means Portrait and ( L) means 
Landscape.
• You cannot use the Enlarge/Reduce  setting with the N in 1 feature.
 
aLoad your document.
bUse the numeric keys to enter the 
number of copies (up to 99).
cPress  Options . Press a or  b to choose 
Page Layout . Press OK.
dPress  a or  b to choose  2in1(P) , 
2in1(L) , 4in1(P) , 
4in1(L)  or Off(1 in 1) .
Press  OK.
ePress  Mono Start  or Colour Start  to 
scan the page.
If you placed the document in the ADF, 
the machine scans the pages and starts 
printing.
If you are using the scanner glass, go 
to step f.
fAfter the machine scans the page, press 
1 to scan the next page.
 
Next Page?
1.Yes 2.No
gPut the next page on the scanner glass.
Press  OK.
Repeat steps f and  g for each page of 
the layout.
hAfter all the pages have been scanned, 
press  2 in step f to finish.
If you are copying from the ADF:4
Insert your document face up in the direction 
shown below:
„ 2 in 1 (P)
 
„2 in 1 (L)
 
„4 in 1 (P)
 
„4 in 1 (L)
 
If you are copying from the scanner 
glass:
4
Insert your document face down in the 
direction shown below:
„ 2 in 1 (P)
 
„2 in 1 (L)
 
„4 in 1 (P)
 
„4 in 1 (L)
 
 
						

							
Chapter 4
32
Out of memory 
message
4
If the memory becomes full while you are 
making copies, the LCD message will guide 
you through the next step.
If you get an  Out of Memory  message 
while scanning a subsequent page, you will 
have the option to press  Mono Start or 
Colour Start  to copy the pages scanned so 
far, or to press  Stop/Exit to cancel the 
operation.
To gain extra memory:
„ Add optional memory. (See  Memory 
board  on page 41.)