Brother DCP 7040 User Manual

Section IV
AppendixesIV
Safety and legal34
Troubleshooting and routine maintenance43
Menu and features78
Specifications85
Glossary95
 

34
A
Choosing a locationA
Place your machine on a flat, stable surface that is free of vibration. Put the machine near a 
standard, grounded electrical socket. Choose a location where the temperature remains between 
10 ° C and 32.5 ° C and the humidity is between 20% to 80% (without condensation).
„ Make sure cables leading to the mach ine do not constitute a trip hazard.
„ Avoid placing your machine on the carpet.
„ Do not place near heaters, air conditio ners, water, chemicals or refrigerators.
„ Do...

Safety and legal35
A
Important informationA
Safety precautionsA
Please read these instructions before attempti ng any maintenance, and keep them for later 
reference. When using your equipm ent, follow basic safety precautions to reduce the risk of fire, 
electric shock or personal injury.
„ DO NOT use this product near wa ter, or in a damp environment.
„ Avoid using this product during an electrical st orm. There may be a remote risk of electric 
shock from lightning.
„ We DO NOT advise using an...

36
WARNING 
Before cleaning the inside of the machine, unplug 
the power cord from the electrical socket.
 
DO NOT handle the plug with wet hands. Doing 
this might cause an electrical shock.
 
Always make sure the plug is fully inserted.
After you have just used the machine, some 
internal parts of the machine will be extremely hot. 
When you open the front or back cover of the 
machine, DO NOT touch the shaded parts shown 
in the illustrations.
 
To prevent injuries, be  careful not to put your 
hands...

Safety and legal37
A
 
Note
The fuser unit is marked with a Caution  label. DO NOT remove or damage the label.
 
 
DO NOT use a vacuum cleaner to clean up scattered toner. Doing this might cause the toner 
dust to ignite inside the vacuum cleaner, pote ntially starting a fire. Please carefully clean the 
toner dust with a dry, lint-free cloth and di spose of it according to local regulations.
If moving your machine, use the handholds provided. First making sure to disconnect any 
cables.
DO NOT use any...

38
IEC60825-1+A2:2001 SpecificationA
This machine is a Class 1 laser product as de fined in IEC60825-1+A2:2001 specifications. The 
label shown below is attached in countries where required.
Laser Diode AA
Wave length: 780 - 800 nm
Output: 10 mW max.
Laser Class: Class 3B
WARNING 
Use of controls, adjustments or performance of  procedures other than those specified in this 
manual may result in hazardous radiation exposure.
 
Disconnect deviceA
This product must be installed near an electrical  socket...

Safety and legal39
A
LAN connection (DCP-7045N only) A
CAUTION 
DO NOT connect this product to a LAN connection that is subject to over-voltages.
 
Radio interferenceA
This product complies with EN55022 (CISPR Pu blication 22)/Class B. When connecting the 
machine to a computer, ensure that you use the following interface cables.
A USB cable which must not exceed 2.0 metres in length.
EU Directive 2002/ 96/EC and EN50419A
 
This equipment is marked with the above recycling  symbol. It means that all the...

40
International ENERGY STAR® Compliance StatementA
The purpose of the International ENERGY STAR® Program is to promote the development and 
popularization of energy-eff icient office equipment.
As an ENERGY STAR
® Partner, Brother Industries, Ltd. ha s determined that this product meets 
the ENERGY STAR
® guidelines for energy efficiency. 
Important safety instructionsA
1 Read all of these instructions.
2 Save them for later reference.
3 Follow all warnings and instru ctions marked on the product.
4...

Safety and legal41
A
12 The power cord, including extensions should be no longer than 5 metres.DO NOT share the same power circuit with other high powered appliances, such as an air 
conditioner, copier, shredder or similar devices.  If you cannot avoid using the printer with these 
appliances, we recommend that you use a high-frequency noise filter.
Use a voltage regulator if th e power source is not stable.
13 DO NOT place anything in front of the machin e that will block printed pages. DO NOT place...

42
TrademarksA
The Brother logo is a registered trademark of Brother Industries, Ltd.
Brother is a registered trademark of Brother Industries, Ltd.
Multi-Function Link is a registered trademark of Brother International Corporation.
Windows Vista is either a registered trademark or a trademark of Microsoft Corporation in the 
United States and/or other countries.
Microsoft, Windows, Windows Server and Internet Explorer are registered trademarks of Microsoft 
Corporation in the United States and/or other...