Boxlight Projectowrite 2 User Manual

							68
Part Names
Power ON / OFF
Turning on the power
1.  Make sure that power cord is rmly and correctly connected to the projector.
2.  Remove the lens cover, and the POWER  indicator will light up in green.
3.  Press POWER button on the control panel or  the remote control to turn on the projector.
4. Rotate the zoom ring to adjust the screen size. 
5. Rotate the focus ring to adjust the focus.
Turning off the power
1.  Press the POWER button on the control  panel or the remote control. The “power off”  
conrmation message appears.
2.  Press the POWER button again while the  message appears.
3.  When the projector enters “Standby” mode,  the POWER indicator will light up in green.
4.  If you don’t use the projector, remove power  cord.
 WARNING
  Do not touch around the lamp cover and the  
exhaust vents during use or just after use, since it  
is too hot.
POWER indicator
AC inlet Outlet
Focus ring Zoom ring
Power off?Please press
key again to power off.
 WARNING
   A strong light is emitted when the projector’s  
power is on. Do not look into the lens of the  
projector or look inside of the projector through 
any of the projector’s openings.
 CAUTION
  Do not turn off the AC power for 60 seconds  
after the lamp is turned on. Doing so could cause  
premature lamp failure.
Back   
						

							69
Setting Up
Back
Ceiling Mounted Installation Guide 
Attach ceiling mount at four-suspension bracket xing points when suspending from a ceiling.  
Special installation is required in order to suspend the projector from the ceiling. Please ask your 
dealer for detals.
Security Anchor
The product is equipped with security  
anchor and PIN LOCK functions to help  
prevent unauthorized removal projector.
MAX M4x8 mm For Mounting.
WARNING
Do not grasp the security anchor to carry projector, since it is not designed for it. 
 The security anchor is not for comprehensive theft prevention measures. It is intended to be  used as supplemental theft prevention measure. 
						

							70
Setting Up
Back
Adjusting The Projector’s Elevation
Use the adjustable foot at the front of the projector to set the image height.
1   Holding the projector, push the foot adjust buttons to loosen the front adjustable foot.
12   Position the front side of the projector to the 
desired height.
3   Release the foot adjust buttons in order to lock the front adjustable feet.
14   After making sure that the front adjustable feet are locked, put the projector gently  
atop.
 CAUTION
*  The adjustment range of front adjustable  foot is 0 to 8.5 degrees.
*  When the foot is adjusted, it may cause the 
shape of the projected image to become  
distorted. Use the keystone correction 
function  to correct this distortion. 
						

							71
Setting Up
Back
AUDIO OUTMOUSERS-232AUDIO OUTDVI OUTVGA OUTVGA OUTRGB IN
AUDIO IN 
VIDEO OUT AUDIO OUT (L)&(R)
S-VIDEO OUTY Pb/Cb Pr/Cr
How To Connect
Laptop or desktop computer
Before starting, make sure that the projector and computer are both turned off.
Connect the computer cable.
Connect either end of the computer cable to the projector’s RGB IN.  
Connect the computer cable from the computer to the projector.
If needed, connect the MONITOR OUT to a monitor to view input from RGB IN.
Tighten the screw on all connectors. 
						

							72
Network Control Software Application
Back
  Register the projector(s) which needs to be controlled.  
“ Auto search ” can help you to seek the projector(s) source easily.  
After registering in the work group, you can start to control the projector.
  Group the projector(s) into different sections.  
You can monitor the status easily by the sort of group name function in the network.
  Monitor the status for each projector.  
a.You can manage and change the monitoring content by System Parameter Setting.  
b. The Lamp timer, lter working time or system warni
ng feedback etc. can be known 
by checking the status for projector(s).
   Control the booked projector(s).  
The status can be refreshed and acquired by monitoring functions; you can also  
operate the function easily by Network Control.
NOTE 
To  monitor  and  control  the  projector(including  stan d-by  mode),  the  following 
conditions need to be ready: 
(1) Projector should already be powered on. 
(2) Projector is connected to network.
(3)  LED  light  of  the  projector  network  port  shows  nor mal.  (Green  light  on,  Orange 
twinkle)
*  
Stand-by mode indictor: Green LED (Power) on the projector’s control panel ashes.
NOTE:  This  Network  Control  Software Application  is  an  o ptional  function  and  support 
model with RJ45 LAN port only.
LAN 
						

							73
Maintenance of Projector
Back
Air Filter 
When a warning message appears to remind you to clean the air lter,  
please replace a new one as soon as possible. Please check and clean the 
air lter periodically. 
Replacing the Air Filter 
When the use time reaches the lter counter time, the projector will  
display a message that indicates to replace a new lter. If there is no spare 
air lter available, please contact your dealer.
Turn off the projector, and unplug the power cord. Allow the projector to sufciently  
cool down.
 Remove the lter cover from the right side of projector.
 Pull out the air lter.
 Install a new air lter.
 Put the lter cover on.
 Reset lter timer after cleaning or changing air lter. (P.35) New one  
						

							74
Maintenance of Projector
Back
Lamp 
1.  If you want to replace new lamp, but the projector was just turned off, please let the projector cool down and unplug power cord at least 60  
minutes.
2.  If the projector is mounted in the ceiling, contact your dealer to replace  the lamp.
Replacing New Lamp 
1. Remove the lamp door. 
2.  Loosen 2 screws of the lamp holder. Take the handle on the top of the  lamp, pull out the lamp straight off the projector.
3. Insert new lamp, lock the lamp door rmly with 2 screws.
4. Put the lamp door on.
5. Please reset the lamp timer after replacing lamp. (P.34)  
						

							Appendix
137.4567.8
316.2 117.8
265
359.95
187.5
255
195
Back
Appearance 
						

							INTERACTIVE PROJECTOR
CMOS 
Sensor
Interactive Projector Packing List.............................................................i 
Accessories Introduction............................................................................ii
Icon Function Introduction.......................................................................iv
Installation Guide for Window OS ........................................................... 1
Installation Guide for Mac OS .................................................................. 9
Troubleshooting ........................................................................................ 14 
						

							i
Interactive Projector Packing List
Check-list of your accessories
   List below is the accessory of the interactive projector. Please check. If there is 
any item missing, contact your dealer. 
1. Accessory Bag 2. Pointer
3. Light Pen 4. Batteries (AA)
5. Batteries (AAA) 6. Hanging String