Boxlight Projectowrite 2 User Manual

							38
MENU
VOL - VOL+MENU
INPUT
PIN Key In Operation
When the projector is turned on and the  
PIN LOCK PROTECTION is set to [ON], 
the image will show as on the right side. 
1.  Press the MENU button on the projector  or remote control. Enter PIN code by  
keypad or remote control.
2. How to enter a PIN code?  You can use control panel or remote 
control.
CONTROL PANEL  KEYSTONE REMOTE CONTROL
The control panel and remote control buttons to enter a sequence  
of PIN code is like the photo below.
(1) Press  button: Select the [ 1 ] 
(2) Press  button: Select the [ 2 ]
(3) Press  button: Select the [ 3 ]
(4) Press  button: Select the [ Enter ] move to next row.(4~6,7~9, 
~OK)
(5)  Press 
 (backspace) item: 
In case you enter a wrong digit, select  to delete the wrong digit you entered.
(6)  Press 
 (backspace) item: 
Once all four digits of the PIN are entered, select  to conrm.
NOTE
If the PIN is incorrect, a ‘ Enter new code ” message will be shown. Please try again. If the PIN  
code input is incorrect for three times, a warning message will show up and the  projector will shut 
itself down in 30 seconds.
If you have no idea about the PIN, please contact your dealer for help.   
						

							Network Control Software Application
39
Network Control Software Application
  Register the projector(s) which needs to be controlled.  
“ Auto search ” can help you to seek the projector(s) source easily.  
After registering in the work group, you can start to control the projector.
  
Group the projector(s) into different sections.  
You can monitor the status easily by the sort of group name function in the network.
  Monitor the status for each projector.  
a.You can manage and change the monitoring content by System Parameter Setting.  
b. The Lamp timer, lter working time or system warni
ng feedback etc. can be known 
by checking the status for projector(s).
   Control the booked projector(s).  
The status can be refreshed and acquired by monitoring functions; you can also  
operate the function easily by Network Control.
NOTE 
To  monitor  and  control  the  projector(including  stan d-by  mode),  the  following 
conditions need to be ready: 
(1) Projector should already be powered on. 
(2) Projector is connected to network.
(3)  LED  light  of  the  projector  network  port  shows  nor mal.  (Green  light  on,  Orange 
twinkle)
*  
Stand-by mode indictor: Green LED (Power) on the projector’s control panel ashes.
NOTE:  This  Network  Control  Software Application  is  an  o ptional  function  and  support 
model with RJ45 LAN port only.
LAN
(Please click here if your projector  
is with high efciency lter.) 
						

							Before Use
40
Before Use
Before To Use Network Control Software
  If the system is Windows 2000, NT 4.0 or XP, the PC should be started by the  
Administrator.
  Before starting the Network Control software, please check the following.
(1) The computer must have Network Control software installed. 
(2)  The projector should be powered on and the LAN wire is well connected to  projector.
(3)  Make sure the computer and projector can connect to network. Network Control  software needs to arrange in TCP/IP network communication and the network cable.
Open Network Control Software
   Click Network control software icon.
 
   Monitor window will show as Graph 1.
   
						

							41
Before Use 
Projector Auto Search.
  Click the  (Projector search), located projector will show on the network 
correctly. 
(Graph2)
   Click  (search again), the projector which is well connected with a PC will be 
shown. 
(Graph3)
   Click  (register projector), the projector information will show on the monitor 
window. Click 
 button (exit), it will cancel the registered item then return to 
register table.
NOTE 
When the security warning window appears while Network Control is executing,  
please select Unblock to decontrol area network linking against from System 
Administer.


 Monitor window      
						

							42
Before Use
Projector Auto Search.
  Projector Auto Search can rank group names or display names by clicking the  
monitor window title (Group Name) or (Projector Name). This will help you easily  
to understand projectors status.
  
After registering, you can click  button (Data single capture) in the tool bar or 
click 
 button (Start Auto Scan) running in this program to monitor the projector.
NOTE 
When pressing 
 About” button for help, you will see icons expla ined as in the chart. 
      
						

							43
Before Use 
Modify The Projector Setting
  If modifying the registered projector setting is needed, please move your cursor to  
the data table and click the item that you would like to modify, the detail will be  
shown on the right side table.
< Graph 5 > : Register Table.
  After setting, you can save the data by clicking  button or cancel by clicking  
button.
Item Description
Display name Show the Host name 
(16 characters at most in ASCII)
IP Address Show the IP Address
Mask Show the Mask
Gateway Show the Gateway
MAC Show up the MAC code
(The default value can not be modied)
DHCP Capture IP address from network sensor
automatically.
< Table 1 > : Setting Windows  
						

							Registering And Conguring The Projector
44
Registering And Conguring The Projector
Delete
  Select the registered projector in monitor window. 
Click mouse right key and select “ 
Delete ” to erase the registered projector data.
< Graph 6 > : Register Table.  
						

							45
Registering And Conguring The Projector
Projector Setting
  Select the registered projector in monitor window. 
Click mouse right key and select “ 
projector setting ” to modify the registered projector data. After nishing the setting,  
you can save by clicking 
 button or cancel by clicking  button.
< Graph 7 > : Register table.
< Graph 8 > :Setting table.   
						

							46
Registering And Conguring The Projector
Projector Setting
 Click  button (system setting) to modify system alert setting.
< Graph 9 >
     
						

							47
Registering And Conguring The Projector
System Setting 
Monitor
Item Description
Lamp Timer Lamp timer from projector. 
Air Filter Alert Air Filter Timer from projector. 
System Status/ 
Tempeture LevelSystem Status and Tempeture. Level from projector in Power On 
status.
Input Source Input Source from projector in Power On status.
< Table 2 >
Default Setting
Item Description
Lamp Timer Alert (Hr.) Default Setting Includes 1000/1500/2000 Hours. 
When Lamp Timer reach alert target, window will show lamp timer 
in red color to remind user to replace the lamp.
Filter Timer Alert (Hr.) Default setting includes 300/500/800/1000/1500 Hours. When Filter 
Timer reach alert target, window will show lter timer in red color to 
remind user to replace the lter.
Auto Detect Timer 
(minutes) Auto Detect setting. Default setting includes 1/3/5/10 minutes; user 
can set the optimal default listed in Table 4.
< Table 3 >
Auto Detect Optimal Setting
Projector Number (Sets) Timer Interval (Minutes)
1~25 1/3/5/10 
26~50 3/5/10
51~100 5/10 
101~255 10> *  The maximum quantity of 
projector monitored is 255.
< Table 4 >