Boxlight Projector P12 User Manual

							Auto Power Off (Min)Sets the countdown timer interval. The countdown timer will start 
when there is no signal being sent to the projector
. The projector 
will automatically power off when the countdown has finished (in 
minutes).
Lamp Settings
Refer to page 32.
High Altitude
On: The built-in fans run at high speed. Select this option when using the projector at altitudes above 2500 feet/762 meters or 
higher.
Off: The built-in fans automatically run at a variable speed ac -
cording to the internal temperature.
Filters Remind (Hour)
Filters Remind (Hour): Set the filter reminder time.
Cleaning Up Remind: Select “Yes” to reset the dust filter hour  counter after replacing or cleaning the dust filter.
 Information
Display the projector information for model name, SNID, source, 
resolution, software version, and aspect ratio on the screen.
 “Dynamic Black”
is available when
“Color Mode” is
set to “Movie”.
 “Dynamic Black”
is not available
when “3D” or
“Interactive” is
enabled.
 When “Dynamic
Black” is avail-
able, “Lamp
Power Mode”
selection is not
available.  
User Controls  
						

							Options |  
Lamp Settings
Lamp Hours Used (Normal)
Display the projection time of normal mode.
Lamp Hours Used (ECO)
Display the projection time of ECO mode.
Lamp Power Mode
Normal: Normal mode.
ECO: Use this function to dim the projector lamp which will 
lower power consumption and extend the lamp life.
Clear Lamp Hours
Choose “Yes” to reset the lamp hour counter.  
User Controls  
						

							3D
 3D

Auto: When an HDMI 1.4a 3D timing identification signal is de
-
tected, the 3D image is selected automatically.
Choose “On” to enable 3D function.
Choose “Off” to disable 3D function.
3D Invert If you see a discrete or overlapping image while wearing DLP 
3D 
glasses, you may need to execute “Invert” to get best match of left/
right image sequence to get the correct image.
3D Format
Use this feature to select the 3D format. Options are: “Frame 
Packing ,” “Side-by-Side (Half) ,” “Top and Bottom,” “Frame 
Sequential ,” and “Field Sequential .”
1080p@24
Use this feature to select 96 or 144Hz refresh rate as using 3D 
glasses in the1080p @ 24 frame packing. 
“Frame Sequen -
tial” is supported
by the DLP Link 3D
input signals from
VGA  /HDMI
connector.
 “Frame Sequen -
tial” / “Field Se-
quential” are sup -
ported by the
HQFS

 3D input
signals  from
Composite/ S-
Video connector
connector.
 “Frame Packing” /
“Side-by-
Side(Half)” / “Top
and Bottom” are
supported from
HDMI 1.4a 3D
input signals.
  
User Controls  
						

							Interactive
Interactive Settings
Choose “On” to enable Interactive function.
Choose “Off” to disable Interactive function.You need to unplug the Mini USB cable that connects NB/desktop 
with the projector before using the Interactive function. After you 
complete the Interactive Settings in OSD, use Mini USB cable to 
connect NB/desktop 
to the projector.
The Interac-
tive function is
available when
displaying graphic
source from HDMI/
VGA  input. Other
sources are  not
supported.
 If “3D” or “Dynam
ic
Black” function  is
enabl ed
 , “Inter-
active” feature is
disabl ed.
 Interaction function:
Please specify that
the Interaction
function is only for
USTi model. The
Interaction function
is not available in
the UST model.  
User Controls  
						

							LAN
 Status
Display the network connection status.
 DHCP
Configure the DHCP settings.

On: Choose “On” to let the projector obtain an IP 
address 
automatically from your network.
Of f: Choose  “Off” to assign I P, Subnet Mask, Gateway, and DNS 
configuration manually.
IP Address
Display an IP address.
Subnet Mask
Display the subnet mask number.
Gateway
Display the default gateway of the network connected to the pro -
jector.
 DNS
Display the DNS number.
MAC Address
Display the MAC address.  
User Controls  
						

							Group Name
Display the group name.
Projector Name
Display the projector name.
 Location
Display the projector location.
 Contact
Display the contact information.  
User Controls  
						

							How to use web browser to control your projector
1. Turn on DHCP to allow a DHCPserver to automatically assign an IP, or
manually enter the required network
information.
2. Then choose apply and press
button to complete the configuration
process.
3. Open your web browser and type in IP Address from the OSD LAN screen then
the web page will display as below: 4. Based on network web-page for the input-string in [tools] tab, the limitation
for Input-Length is in the below list
(“space” and the other punctuation
keys included):
Category
ItemInput-Length 
(characters)
Crestron Control IP Address
15
IP ID 2
Port 5
Projector Projector Name 10
Location
9
Assigned To 9
Network  
Configuration DHCP (Enabled)
(N/A)
IP Address 15
Subnet Mask 15
Default Gateway 15
DNS Server 15
User Password Enabled
(N/A)
New Password 15
Confirm 15
Admin Password Enabled
(N/A)
New Password 15
Confirm 15 
	When you use the projector IP
address, you can 't link to your
service server.  
User Controls  
						

							When making a direct connection from your computer to the projector
Step 1: Find an IP Address (192.168.0.100) from LAN function of projector.
Step 2: Select apply and press “Enter” button to submit function or press “menu” key to  exit.
Step 5: Click Use the following IP  address, and type in as below:
1) IP address: 192.168.0.100
2) Subnet mask: 255.255.255.0
3) Default gateway:192.168.0.254
Step 6: To open Internet Options, click IE web browser, click Internet Options, 
click the Connections tab and click 
“LAN Settings...”.
Step 7: The Local Area Network (LAN) Setting dialog box appears. In the 
Proxy Server area , cancel the 
Use a proxy server for your LAN  
check box, then click “OK” button 
twice.
Step 8: Open your IE and type in the IP  address of 192.168.0.100 in the 
URL then press “Enter” key.
Step 3: To open Network Connections, 
click Start, click Control Panel, 
click Network and Internet 
Connections, and then click 
Network Connections. Click the 
connection you want to configure, 
and then, under  Network Tasks 
, click Change settings of this 
connection .
Step 4: On the General tab, under  This connection uses the 
following items , click Internet 
Protocol (TCP/IP) , and then click 
“Properties.”  
User Controls          
						

							Crestron RoomView Control 
Tool
Crestron RoomView™ provides a central monitoring station for 250
+ control systems on a single Ethernet network (more are possible - 
the number depends on the combination of IP ID and IP  address). 
Crestron RoomView monitors each projector, including projector’s 
online status, system power, lamp life, network setting and hardware 
faults, plus any custom attribute as defined by the Administrator. 
The Administrator can add, delete, or edit room information, contact 
information and events, which are logged automatically by the 
software for all users. (Operation UI as following image)
1. Main Screen2. Edit Room  
User Controls  
						

							3. Edit Attribute
4. Edit Event
For further information, please visit:
http://www.crestron.com & www
.crestron.com/getroomview.  
User Controls