Boxlight Projector P12 User Manual

							InstallationConnecting the Projector
Connect a Desktop/Laptop Computer
E62405SPR
MOLEX
1
2
4
5
6
3
7
8
9
10
Due to applica-
tion discrepan-
cies in differentcountries/regions,
certain regions
may include differ-
ent accessories

Remote keys vary
with projector
types.
1................................................................................................. RS232 Cable 
2..................................................................................................... USB Cable 
3..................................................................................................... VGA Cable 
4................................................................................................... HDMI Cable 
5.......................................................................................... Audio Input Cable 
6.................................................................................................. Power Cable
7....................................................................................... Audio Output Cable 
8.......................................................................................... Audio Input Cable 
9.................................................................................................... RJ45 Cable 
10....................................................................................... VGA Output Cable
Router / Network Switch Microphone
Audio Output
External 
Display 
						

							E62405SP
R
1
5
6
4
7
3
8
2
Connect to Video Sources
Due to
application
discrepancies  
in
different
countries/
regions, certain
regions may
include different
accessories .
Remote keys vary
with projector
types.
1................................................. 15-Pin to 3 RCA Component/HDTV Adapter2................................................................................................... HDMI Cable
3...........................................................................................Audio Cable/RCA
4................................................................................................... Audio Cable
5.................................................................................................. Power Cable
6................................................................................. Composite Video Cable
7...........................................................................................Audio Cable/RCA
8.......................................................................................... Audio Input Cable
Composite Video Output DVD player, STB (Set-top 
Box), HDTV receiver
Microphone Audio Output 
						

							Powering the Projector On / Off
Turn on the
projector first and
then select the
signal sources.
Powering On the Projector 1.
Securely connect the power cord and signal cable. When
connected, the POWER/STANDBY LED will turn Red.
2. Turn the lamp on by pressing  “ ” button either on the projec-
tor or on the remote. Once pressed, the POWER/STANDBY
LED will now turn Blue. 
3. Turn on and connect the source that you want to display  on
the screen (computer, notebook, video player, etc).
The projector will detect the source automatically. If not,
press menu button and go to “OPTIONS” to make sure “Auto
Source” is enabled.
 If you connect multiple sources at the same time, press the
“INPUT” button on the control panel or direct source keys on
the remote control to switch between inputs.
	When the projector
is in standby mode
(
						

							Contact the
nearest service
center if the
projector displays
these symptoms.
When the warning indicators (see below) come on, 
the projector will automatically shutdown: 
“LAMP” LED indicator lights  up in solid Red.
 “TEMP” LED flashes Red. This indicates the projector  
has
overheated. Under normal conditions, the projector can  
be
switched back on. Unplug the power cord from the projector, wait for 30 seconds 
and try again. If the warning indicator light
s up again, please 
contact your nearest service center for assistance. 
Powering Off the Projector
1.Press the “” button on the remote control or on the control panel to turn the projector
 off.
The following message will be displayed on the screen. Press the “ 
” button again to confirm; otherwise the 
message will disappear after 15 seconds. When you 
press the “  ” button for the second time, the fan will 
start cooling the system and the projector will shut down. 2.
The cooling fans continue  the cooling  cycle for about 35
seconds  and subsequently the  POWER/STANDBY LED will
Flash Blue. When the POWER/ST ANDBY LED lights  up
solid  Red, the projector has entered standby mode.
If you wish to turn the projector back on, you must wait  until
the projector has completed the cooling cycle and  has
entered standby mode. Once in standby mode, simply
press “  ” button to restart the projector.
3. Disconnect the power cord from the electrical outlet and  the
projector.
4. Do not turn the projector on immediately following a power
off procedure.
Warning Indicator    
						

							Adjusting the Projected Image
Adjusting the Projector’s Height 
The projector is equipped with Adjustable feet for adjust-
ing the image height.
1.Locate the adjustable feet you wish to modify on theunderside of the projector.
2. Rotate the adjustable ring clockwise to raise the projector or counter clockwise to lower it. Repeat with the remaining
feet as needed.
Tilt-Adjustment Feet
Tilt-Adjustment Ring    
						

							Adjusting the Projector’s Focus
To focus the image, slide the focus lever to left/right until the 
image is clear.  
 WXGA series: The projector will focus at distances from 
1.499 to 2.06 ft. (0.457 to 0.628 meter).
Focus Lever      
						

							17
Adjusting Projection Image Size (Diagonal)
 WXGA series: Projection Image Size from 80” to 110” (2.032 
to 2.794 meters).
Diagonal of Screen Screen Size
Projection 
Distance (D) Projection 
Distance (A) V-Offset (B)
cm
W (Width) H (Height) cm cmcm
80 172.3 107.7 45.720.512
81 174.5 109 46.2 21.112.2
82 176.6 110.4 46.821.612.4
83 178.8 111 . 7 47.4 22.212.6
84 180.9 113.1 47.922.812.8
85 183.1 114.4 48.523.313
86 185.2 115.8 49.123.913.2
B A
D D= Throw distance
B= Offset-
4.19cm
A= Throw distance –25.17cmD=Throw distance
B=Offset - 4.19cm
A=Throw distance - 25.17cm    
						

							Diagonal of Screen Screen Size
Projection 
Distance (D) Projection 
Distance (A) V-Offset (B)
cm
W (Width) H (Height) cm cmcm
87 187.4 117.1 49.724.513.4
88 189.5 118.5 50.225.113.6
89 191.7 119.8 50.825.613.8
90 193.9 121.2 51.426.214
91 196122.5 51.9 26.814.2
92 198.2 123.9 52.527.314.4
93 200.3 125.2 53.127.914.6
94 202.5 126.5 53.728.514.8
95 204.6 127.9 54.229.115
96 206.8 129.2 54.829.615.2
97 208.9 130.6 55.430.215.4
98 211.1 131.9 55.930.815.6
99 213.2 133.3 56.531.315.8
100 215.4 134.6 57.131.916
101 217.5 136 57.6 32.516.2
102 219.7 137.3 58.233.116.4
103 221.9 138.7 58.858.516.6
104 224140 59.4 59.116.8
105 226.2 141.4 59.959.717
106 228.3 142.7 60.560.317.2
107 230.5 144 61.1 60.817.4
108 232.6 145.4 61.661.417.6
109 234.8 146.7 62.26217.8
11 0 236.9 148.1 62.862.518    
						

							Control Panel
Control Panel & Remote Control
Using the Control Panel
POWERPress “Power” to turn ON/OFF the projector.
Enter  Press “Enter” to confirm your selected item.
INPUT Press “INPUT” to select signal source.
MENU Press “MENU” to launch the on-screen display 
(OSD) menu. To exit OSD, press “MENU” again.
Four Directional 
Select Keys Press 
 to select item.
LAMP LED This indicates the lamp status of the projector.
TEMP LED This indicates the lamp status of the projector.
ON/STANDBY 
LED This indicates the status of the projector.  
User Controls       
						

							Remote Control
Using the Remote Control
LEDLED Indicator.
Power   
Press Power to turn ON/OFF the 
projector.
Exit Press “Exit” to close the OSD menu.
Zoom + Zoom in the display of the projector
Reset Reset the adjustments to default set-
ting.
Zoom - Zoom out the display of the projector.
Enter Confirm your selected item.
Input Press “Source” to select an input 
signal.
Auto Automatically synchronizes the 
projector to the input source.
Four Directional 
Select Keys Use 
 to select items or make 
adjustments to your selection.
Keystone +/- Adjust image keystone by tilting the 
projector.
Volume +/- Adjust the Volume.
Aspect  Use this function to choose your de
-
sired aspect ratio.
Menu Press “Menu” to launch the on-screen 
display (OSD) menu. To exit OSD, 
press “Menu” again.
VGA1 Press “VGA1” to choose VGA IN 1 
connector.  
User Controls