Boxlight Bl X25nu/x25nu User Manual

							49
Before Use 
		After registering, you can click  button (Data single capture) in the tool bar or 
click 
 button (Start Auto Scan) running in this program to monitor the projector.
NOTE
When pressing  "About " button for help, you will see icons explained as in the chart.\
 
Projector Auto Search. 
						

							50
Before Use
Modify The Projector Setting
		If modifying the registered projector setting is needed, please move you\
r cursor to 
the data table and click the item that you would like to modify, the detail will be 
shown on the right side table.
< Graph 5 > : Register Table
		After setting, you can save the data by clicking  button or cancel by clicking  
button.
Item Description
Display nameShow the Host name
(16 characters at most in ASCII)
IP Address Show the IP Address
Mask Show the Mask
Gateway Show the Gateway
MAC Show up the MAC code
(The	default	value	can	not	be	modified)
DHCP Capture IP address from network sensor
automatically.
< Table 1 > : Setting Windows 
						

							51
Registering And Configuring The Projector
Delete
		Select the registered projector in monitor window. Click mouse right key and select 
" Delete " to erase the registered projector data.
< Graph 6 > : Register Table. 
						

							52
Registering And Configuring The Projector
Projector Setting
		Select the registered projector in monitor window. Click mouse right key and select 
"projector	setting"	to	modify	the	registered	projector	data.	
After	finishing	the	setting,	
you can save by clicking 
 button or cancel by clicking  button.
< Graph 7 > : Register table.
< Graph 8 > :Setting table. 
						

							53
Registering And Configuring The Projector
Projector Setting
	Click  button (system setting) to modify system alert setting.
< Graph 9 >
  
						

							54
Registering And Configuring The Projector
System Setting
Monitor
ItemDescription
Lamp TimerLamp timer from projector.
Air Filter Alert Air Filter Timer from projector.
System Status/
Tempeture Level System Status and Tempeture. Level from projector in Power On 
status.
Input Source Input Source from projector in Power On status.
< Table 2 >
Default Setting
Item Description
Lamp Timer Alert (Hr.)Default Setting Includes 1000/1500/2000 Hours.
When Lamp Timer reach alert target, window will show lamp timer 
in red color to remind user to replace the lamp.
Filter Timer Alert (Hr.) Default setting includes 300/500/800/1000/1500 Hours. When Filter 
Timer	reach	alert	target,	window	will	show	filter	timer	in	red	color	
to	remind	user	to	replace	the	filter.
Auto Detect Timer 
(minutes) Auto Detect setting. Default setting includes 1/3/5/10 minutes; user 
can set the optimal default listed in Table 4.
< Table 3 >
Auto Detect Optimal Setting
Projector Number (Sets) Timer Interval (Minutes)
1~25 1/3/5/10
26~50 3/5/10
51~100 5/10
101~255 10< * 
 
The maximum quantity of 
projector monitored is 255.
                          < Table 4 > 
						

							55
Registering And Configuring The Projector
Link
		Select the registered projector in monitor window. Click mouse right key and select 
" Link " to show up the control panel table and the projector connected \
status.
< Graph 12 > : The control panel table 
						

							56
Control Panel Window Introduction
		Power Control
Icon Name
Power on
Power off
		
Input Source
Icon Name
Video
S-Video
Y,Pb,Pr
DVI-I
RGB 1
Change Input Source
		Function Key
Icon Name
Icon Name
UpFreeze
DownBlank
LeftKeystone Correction +
RightKeystone Correction -
MenuIncrease Brightness
Auto SyncDecrease Brightness
MuteHigher Contrast 
						

							57
Control Panel Window Introduction
	Function Key
Icon Name
Lower Contrast
Zoom In
Zoom Out
Volume Up
Volume Down
	
Projector Status
Icon Name
System Status
Input Source Status
Lamp Timer
Air Filter Timer   
						

							58
Control Panel Window Introduction
	Network Control Window introduction
Icon
Name Description
Scan allCapture the all registered projectors’ information one 
time only.
Start Auto ScanAccording to the system setting, get the projector 
information automatically.
Stop Auto Capture Stop scanning the projector information.
Auto SearchSearch the projector in the same network to register and 
modify the setting.
Open Project File
Open	project	file	which	was	saved.
Save Project File Save the registered projector in this project.
System Setting Setting the projector system reminder message.
AboutIcon content description.
ExitExit the Network software.
Register projector Register projector’s information.
ExitCancel registered information.