Boxlight Bl X25nu/x25nu User Manual

							29
MENU
NOTE	 ►To	capture	an	image	is	available	only	in	computer	mode.
	 ►The	area	that	can	be	captured	is	512	x	384	dots.
Advanced Menu
Logo Capture
How to use this function?
		 Select Logo Capture item in the logo 
setting	menu,	and	press	►	button.
		 You can see the red frame to select 
captured area.
		 Use 4 direction buttons to adjust the 
position of the frame.
		 Press “MENU” to start capturing and 
display a dialog. 
Image

Logo Capture In Progress. 
						

							30
MENU
Presentation Menu
Step:
1.	Use	the	▲	/▼buttons	
to select an item.
2.	 Use	the	◄	/	►	buttons	
to select an item or 
adjust the value.
Item Selection Description
AUTO CEILING OFF / ONAutomatically invert the image when the projector is turned 
upside down, i.e. when the projector is mounted on the 
ceiling.
FRONT EXECUTE Normal projection mode.
CEILING EXECUTE Mirror the image vertically, only for the projector mounted 
upside down.
REAR EXECUTEMirror the image horizontally, only for projecting onto rear 
projection screen.
CEILING AND 
REAR EXECUTEMirror the image horizontally and vertically. Projecting onto 
a rear projection screen while projector is upside down.
LAMP MODE NORMAL / 
ECONOMICSwitch lamp mode between normal or ECO mode.
LAMP Show lamp use time.
RESET LAMP 
TIMER EXECUTEAfter changing a new lamp, execute this function to reset 
the lamp timer. 
						

							31
MENU
NOTE
►		The	replacement	warning	message	is	set	to	appear	after	about	2000	hours	of	lamp	use	in	order	
to maintain the initial brightness. When replacement message appears, replace the lamp with a 
new one as soon as possible, even if the lamp is still workable.
Presentation Menu
Reset Lamp Timer
The lamp timer is the time counted after the last resetting. The usage time of the lamp 
is	shown	in	the	PRESENTATION	Menu.	Pressing	the	RESET 	button	or	the	►	button	
displays a dialog.
To	reset	the	lamp	time,	select	the	RESET 	using	the	►	button. 
						

							32
MENU
Security Menu
Step:
1.	Use	the	▲	/▼buttons	to	
select an item.
2.	 Use	the	◄	/	►	buttons	
to select an item or adjust 
the value.
Item Selection Description
PIN LOCK 
PROTECTIONOFF
ON 1
ON 2OFF: Turn off PIN lock protection.
ON 1: 
  After plugging in AC power, you need to key in PIN 
code	at	the	first	time	of	use.	If	the	 AC	power	stays	
unplugged, you do not need to key in PIN code next 
time when you use the projector.
ON 2:    You need to key in PIN code every time when you 
turn on the projector.
 CAUTION:
Once the PIN code had been set, the projector cannot be 
used unless you enter the correct PIN code.
 
MODIFY PIN EXECUTE 1. Press “ MENU ” on the projector or remote control.
2.		
Use	the	►	button	to	select	the	MODIFY 	PIN	item	of	the	
SECURITY category.
3.		 Press 	the 	► 	button 	to 	change 	PIN 	LOCK 	PROTECTION 	
mode.
4. Please enter the original PIN code.
    (a)   If the PIN is correct, system will allow you to change 
a new PIN code.
    (b)   If the PIN is incorrect, a “ Code Error ” message will appear.
5.	Please 	enter 	a 	new 	PIN 	code. 	And 	then 	enter 	again 	to 	confirm.
NOTE:
(1)    To change the PIN lock protection state, you must 
enter	the	PIN	code	first.
(2)	Please	enter:	0000	for	first-time	use.
(3)    To avoid unnecessary trouble, if you activate the [PIN 
Lock Protection], it is highly recommended that you 
write down the PIN code and store it in a safe place. 
						

							33
MENU
Security Menu
Step:
1.	Use	the	▲	/▼buttons	to	
select an item.
2.	 Use	the	◄	/	►	buttons	to	
select an item or adjust the 
value.
Item Selection Description
FILTER TIMERShow	the	filter	use	hour.
RESET FILTER
TIMER EXECUTE
Reset	the	filter	timer	after	cleaning	/	changing	filter.
FILTER COUNTER 500 hours
800 hours
1000 hoursSelect (500 / 800 / 1000 hours) depending on the 
environment.(default : 500 hours). Please see as below.
MAC ADDR. If purchasing LAN control module, "MAC ADDR." will be 
shown in "Security" Menu. 
MAC address stands for unique Media Access Control 
address of LAN control module and displays with six 
groups of two hexadecimal digits.
CLOSED CAPTION OFF(Default)
C.C1
C.C2
C.C3
C.C4
T1
T2
T3
T4The Closed Caption function intimates the sound effects, 
dialogue, and narration in the content of the television 
program or video source.
Caption (C.C1~C.C4) : Display closed caption Text 
(T1~T4) : Display text data, which is for additional 
information such as news reports or a TV program guide.
NOTE : 
  This function is available only in video / S-Video 
source.
LAN MODULE OFF
ONIf purchasing LAN control module, "LAN MODULE" will 
be shown in "Security" Menu.
Select ON/OFF to turn on/off LAN control feature. 
						

							34
MENU
NOTE
►	Please	reset	the	Filter	time	only	when	you	replace	the	filter.
Auto Filter Alert
Auto	Filter	Alert	is	in	SECURITY 	category	to	show	the	air	filter	use	time	and	alert	user	
to	change	filter.	Pressing	►	cursor	button	will	display	a	dialog.	 When	the	operating	time	
reaches	the	set	time,	a	warning	message	will	appear	on	the	screen	to	remind	user	of	filter	
cleaning / replacing.
Filter Replace...
Filter has been used for more than 500 hours. 
						

							35
MENU
POWERLASER
MOUSE-LAUTO BLANKMOUSE-R
MUTE
MENU
INPUTLASER
INDICATOR
POWER
LASER
MOUSE-L
AUTO BLANK
MOUSE-R
MUTE
MENU
INPUTLASER
INDICA TOR
PIN Key In Operation
When the projector is turned on and the 
PIN LOCK PROTECTION is set to [ON], 
the image will show as on the right side.
1.  Press the MENU button on the projector 
or remote control. Enter PIN code by 
keypad or remote control.
2.  How to enter a PIN code? 
You can use control panel or remote 
control.
CONTROL PANEL 
KEYSTONE REMOTE CONTROL
The control panel and remote control buttons to enter a sequence 
of PIN code is like the photo below.
(1)	Press	◄	button:	Select	the	[	1	]
(2)	Press	▲	button:	Select	the	[	2	]
(3)	Press	►	button:	Select	the	[	3	]
(4)	Press	▼	button:	Select	the	[	Enter	]	move	to	next	row.(4~6,7~9,	
~OK)
(5)   Press 
 (backspace) item: 
In case you enter a wrong digit, select  to delete the wrong digit you entered.
(6)   Press 
 item: 
Once all four digits of the PIN are entered, select 	to	confirm.
NOTE
If the PIN is incorrect, a ‘ Enter new code ” message will be show\
n. Please try again. If the PIN 
code input is incorrect for three times, a warning message will show up \
and the  projector will shut 
itself down in 30 seconds.
If you have no idea about the PIN, please contact your dealer for help. 
						

							36
Network Control Software Application
	 
Register the projector(s) which needs to be controlled. 
" Auto search " can help you to seek the projector(s) source easily. 
After registering in the work group, you can start to control the projec\
tor.
		Group the projector(s) into different sections. 
You can monitor the status easily by the sort of group name function in t\
he network.
		Monitor the status for each projector. 
a.You can manage and change the monitoring content by System Parameter Sett\
ing. 
b.	
The 	Lamp 	timer, 	filter 	working 	time 	or 	system 	warning 	feedback 	etc. 	can 	be 	known 
by checking the status for projector(s).
		 Control the booked projector(s). 
The status can be refreshed and acquired by monitoring functions; you ca\
n also 
operate the function easily by Network Control.
NOTE
To  monitor  and  control  the  projector(including  stand-by  mode),  the  following 
conditions need to be ready:
(1) Projector should already be powered on.
(2) Projector is connected to network.
(3)   LED  light  of  the  projector  network  port  shows  normal.  (Green  light  on,  Orange 
twinkle)
*  
Stand-by	mode	indictor:	Green	LED	(Power)	on	the	projector’s	control	panel	flashes.
NOTE:   
This  Network  Control  Software Application  is  an  optional  function  and  support 
model with RJ45 LAN port only. LAN 
						

							37
Before Use 
Before To Use Network Control Software
		If the system is Windows 2000, NT 4.0 ,XP ,Vista or Windows 7, the PC should be 
started by the Administrator.
		
Before starting the Network Control software, please check the following\
.
(1) The computer must have Network Control software installed.
(2)    The projector should be powered on and the LAN wire is well connected to\
 
projector.
(3)The LAN module ON/OFF item in SECURITY menu of OSD should be setting ON.
(4)   Make sure the computer and projector can connect to network. Network Con\
trol 
software needs to arrange in TCP/IP network communication and the network cable.
Open Network Control Software
		 Click Network control software icon.
 
		 Monitor window will show as Graph 1.
 
						

							38
Network Control Software Application
Network Control is provided in visual interface, it can help user to mon\
itor and manage the 
projector(s) status in the local area network.
1.  Register the projector(s) which needs to be controlled. 
" Auto search " can help you to seek the projector(s) source easily. 
After registering in the work group, you can start to control the projec\
tor.
2.   Group the projector(s) into different sections. 
You can monitor the status easily by the sort of group name function in t\
he network.
3.    	 Monitor the status for each projector. 
a.You can manage and change the monitoring content by System Parameter Sett\
ing. 
b.	The	Lamp	timer,	filter	working	time	or	system	warning	feedback	etc.	can	be	known  
by checking the status for projector(s).
4.    Control the booked projector(s). 
   The status can be refreshed and acquired by monitoring functions; you can also operate the function 
easily by   Network Control.
NOTE:
To monitor and control the projector(including stand-by mode), the foll\
owing conditions need to be 
ready:
(1) Projector should already be powered on.
(2) Projector is connected to network.
(3)   LED light of the projector network port shows normal. (Green light on, \
Orange twinkle)
*		 Stand-by	mode	indictor:	Green	LED	(Power)	on	the	projector’s	control	panel	flashes.
Before To Use Network Control Software1. If the system is Windows 2000, XP or Vista, the PC should be started by the Administrator.
2.   Before starting the Network Control software, please check the following\
.
    (2-1) The computer must have Network Control software installed.
    (2-2)    The projector should be powered on and the LAN wire is well connected to\
 projector.
    (2-3) The LAN module ON/OFF item in SECURITY menu of OSD should be setting ON.
    (2-4)   Make sure the computer and projector can connect to network. Network Con\
trol software 
needs to arrange in TCP/IP network communication and the network cable.
  
   NOTE: 
         IE8 browser & 1024x768 viewing resolution is recommended.